• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.128-136
• /
• 2007

It is well known that two representative methods satisfy EURO-IV regulation from EURO-III. The first method is to achieve the regulation through the reduction of NOx in an engine by utilizing relatively high EGR rate and the elimination of subsequently increased PM by DPF. However, it results in the deterioration of fuel economy due to relatively high EGR rate. The second is to use the high combustion strategy to reduce PM emission by high oxidation rate and trap the high NOx emissions with DeNOx catalysts such as Urea-SCR. While it has good fuel economy relative to the first method mentioned above, its infrastructure is demanded. In this paper, the number distribution of nano PM has been evaluated by Electrical Low Pressure Impactor(ELPI) and CPC in case of Urea-SCR system in second method. From the results, the particle number was increased slightly in proportion to the amount of urea injection on Fine Particle Region, whether AOC is used or not. Especially, in case of different urea injection pressure, the trends of increasing was distinguished from low and high injection pressure. As low injection pressure, the particle number was increased largely in accordance with the amount of injected urea solution on Fine Particle Region. But Nano Particle Region was not. The other side, in case of high pressure, increasing rate of particle number was larger than low pressure injection on Nano Particle Region. From the results, the reason of particle number increase due to urea injection is supposed that new products are composited from HCNO, sulfate, NH3 on urea decomposition process.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.8
• /
• pp.907-914
• /
• 2015

Due to the global warming, the restriction for emitting the green-house gas is strengthened and a main ingredient of the green-house gas is carbon dioxide ($CO_2$). In order to reduce the amount of $CO_2$, the low-carbon and long-life of the construction and the construction materials management system based on the radio frequency identification (RFID) technique have been actively studied in the construction field. The conventional construction management system based on RFID only focuses on the study and experiment for managing the used amount and location of the construction materials in the construction stage, but it does not consider the study for the status management system for the recycling materials in the construction stage or the building deactivation. In this paper, we propose the effective RFID system for managing the status of the construction materials during the construction stage or the building deactivation. Employing RFID with the frequency of 900MHz, the proposed system consists of the reader unit, communication unit, and memory unit, and its tags are attached in the surface or inside of the construction materials.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2012.06a
• /
• pp.273-274
• /
• 2012

Companies are facing challenges to have high competitiveness because of continuous oil price rising and CO2 emissions regulations. Thus, companies are trying hard to construct effective logistics and operation system to achieve high customer service quality and saving cost. Also the ec-friendly idustrial complex is needed. Busan is in process to construct GILC(Global Industry Logistics City) in west Busan province to achieve high competitiveness and support lack of industrial complex. To construct this kind of logistics industrial complex, it needs logistics system through proper policy and freight transportation co-operation. Especially, efficient management through logistics hierarchy construction in industrial complex is very important for low cost and eco-friendly point of view. Therefore, this paper aims to analyze logistics system and suggest operation model to present logistics complex construction base data.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2014.06a
• /
• pp.221-222
• /
• 2014

Companies are facing challenges to have high competitiveness because of continuous oil price rising and CO2 emissions regulations. Thus, companies are trying hard to construct effective logistics and operation system to achieve high customer service quality and saving cost. Also the ec-friendly idustrial complex is needed. Busan is in process to construct GILC(Global Industry Logistics City) in west Busan province to achieve high competitiveness and support lack of industrial complex. To construct this kind of logistics industrial complex, it needs logistics system through proper policy and freight transportation co-operation. Especially, efficient management through logistics hierarchy construction in industrial complex is very important for low cost and eco-friendly point of view. Therefore, this paper aims to analyze logistics system and suggest operation model to present logistics complex construction base data.

• Journal of Power System Engineering
• /
• v.21 no.6
• /
• pp.68-78
• /
• 2017

Major countries have tighten their NOx regulation of diesel passenger cars. In the case of the EU, the regulation has been toughen up to 6.25 times since 2000. Despite the regulation the NOx concentration of the ambient has not been reduced proportionally. Futhermore, some manufacturers were disclosed using a defeat device for meeting the regulation illegally. As these issues, to reduce NOx emission practically, Korea and the EU introduced the real-world driving emission(RDE) regulation and the test method that will be applied after 2017. Also, the US has used the test equipment(PEMS) to detect a defeat device. In this paper, for the regulation to make a soft landing in Korea, 4 diesel passenger cars which met Euro 6a~6b regulation and were equipped with LNT/SCR were tested at a chassis dynamometer with environmental chamber applying the off-cycles(FTP, US06, SC03, HWFET and CADC) and several ambient condition(-7 and $14^{\circ}C$) as well as certification mode(NEDC, WLTC@ $23^{\circ}C$). The result of the test showed that the ambient temp. and the engine load as a test mode impacted the NOx emission of the cars while the vehicles with SCR emitted NOx lower than with LNT. Additionally, to propose an effective RDE test method, the above result was compared with the results of the other papers which tested RDE using the same cars.

• Journal of the Korean Institute of Gas
• /
• v.13 no.4
• /
• pp.46-52
• /
• 2009

Hydrogen can extend the lean misfire limit to a large extent when it is mixed with conventional fuels for an internal combustion engine. This study is about fuel reforming to produce hydrogen enriched gas as a fuel for engine. Especially gasoline, which consists of numerous hydrocarbon fuels, considered as source of reformed gas. Various hydrocarbons, including commercial fuel were reformed and potentialities of reformed gas on vehicles were accessed. The reforming efficiency and hydrogen yield were observed. Maximum hydrogen yield were found with different gas hourly space velocity(GHSV) and O2/C ratio of reforming conditions.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2012.03a
• /
• pp.18-18
• /
• 2012

전 세계적으로 이산화탄소 배출량 저잠을 위해 모든 산업분야에서 연구개발의 중점을 두고 있다. 그의 일환으로 자동차 산업에서는 EU규제에 따라 리사이클이 가능한 소재 개발이 요구되고 있으며, 그중 많은 양이 사용되고 있는 PU Foam의 대체 재료 개발이 시급한 실정이다. 기존 자동차의 흡음재로 주로 사용되고 있는 PU Foam 소재는 통기성이 부족할 뿐만 아니라 연소 시 인체에 유해한 HCN Gas를 발생시키고, 한번 성형된 부품은 Recycle 및 Re-Use가 불가능하다는 단점이 있다. 또한 장시간 사용시 황변 발생과 악취가 발생하는 등으로 최근 대두되고 있는 자동차 내장재 감성품질 향상 측면에 한계를 나타내고 있다. 이러한 Low Melting 성능을 가지는 PET 부직포 소재의 한계를 극복하기 위하여 저융점 성능의 Elastic Fiber의 개발과 함께 고탄성 복합부직포 소재의 개발을 통해 높은 변형률과 우수한 복원력을 나타내는 환경친화형 열가소성 탄성체(Thermoplastic Elastomer) 개발을 추진하고 있다. 고탄성 복합부직포는 자동차 내장재 성형 시 열을 가하더라도 Elastomer 자체의 탄성 발현을 통해 초기의 Bulky성을 유지할 수 있으며, Recycle 및 Re-use가 가능하여 환경 친화적인 측면에서도 큰 장점을 갖고 있다. 자동차용 흡음 내장재뿐만 아니라 각종 수송용 차량의 경량화 및 쾌적성 향상을 위한 용도로써 자동차 내장용 PU Foam의 57% 이상을 차지하고 있는 Seat Cushion재 등의 대체가 가능하며, 다양한 산업분야에서 사용되고 있는 PU Foam의 대체로 다양한 용도 전개가 가능할 것으로 예상된다. 본 연구에서는 PU Foam의 대체 재료로 각광받고 있는 Elastic PET를 개발하여 자동차 내장재로의 적용 가능성을 검토하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.3
• /
• pp.1677-1683
• /
• 2015

To cope with exhaust gas regulation, Diesel engine applied to electronic control system. As it accurately regulated the injected fuel mass and the fuel efficiency and the output are increased but the noise and the vibration are decreased. In order to keep the performance of Electronic Diesel Control System, it is important to accurately control the fuel pressure. However, when the regulator of fuel pressure is not controlled properly, the failure phenomenons(starting failure, staring delay, accelerated failure, engine mismatch et al.) occur because the fuel pressure is not stabilize. In this study, effects on a fuel pressure, engine rotating speed according to the control rate of fuel-pressure regulator are investigated in order to analyzed the performance variation with failure of fuel-pressure regulator. As a result, when the control rate of a fuel-pressure regulator is 4%~6% lower than that of standard condition, the variation of engine's rpm and return fuel flow is increased, and the abnormal condition was occurred. Besides, it is possible to diagnose the failures on fuel-pressure regulator under these conditions.

• Journal of the Economic Geographical Society of Korea
• /
• v.7 no.2
• /
• pp.157-170
• /
• 2004

The Boundary Region in Gyeonggi Province has environmental vulnerability due to the increasing development pressure although usually regarded as an ecologically well-preserved region. This paper is aimed to analyze the status of environmental loading on natural resources of the Boundary Region in Gyeonggi Province through investigating land-use conversion pattern during the past 15 years(1985-2000), the attitude of the local community towards conservation policy, and the status of environmental treatment facilities for water quality management. The results are as follows. Firstly, the development pressure has been focused upon the southwestern part of the Boundary Region in Gyeonggi Province such as Gimpo, Paju, Dongduocheon, and Yangju since 1995. Secondly, local residents' strong aversion exists towards the conservation policy led by the government because of their underdevelopment. Finally, the risk of environmental degradation is high because the region is not equipped with adequate environmental treatment facilities for water quality management. The status of environmental loading in the Boundary Region suggests the necessity to establish a well-designed management plan for natural resources in this area.

• Journal of Navigation and Port Research
• /
• v.38 no.2
• /
• pp.171-176
• /
• 2014

Companies are facing challenges to have high competitiveness because of continuous oil price rising and CO2 emissions regulations. Thus, companies are trying hard to construct effective logistics and operation system to achieve high customer service quality and saving cost. Also the ec-friendly idustrial complex is needed. Busan is in process to construct GILC(Global Industry Logistics City) in west Busan province to achieve high competitiveness and support lack of industrial complex. To construct this kind of logistics industrial complex, it needs logistics system through proper policy and freight transportation co-operation. Especially, efficient management through logistics hierarchy construction in industrial complex is very important for low cost and eco-friendly point of view. Therefore, this paper aims to analyze logistics system and suggest operation model to present logistics complex construction base data.