• Journal of Food Hygiene and Safety
• /
• v.33 no.4
• /
• pp.272-279
• /
• 2018

The high pressure processing (HPP) is a technology which can preserve the quality of foods, such as the fresh taste, incense, texture, vitamin content, and so on, by minimizing the heating process. It does so by applying an instantaneous and uniform pressure that is the same as the water pressure that is 60 km deep in the sea. HPP is a technology that can inhibit food poisoning and spoilage caused by microorganisms and is currently an actively studied area. In this study, we investigated the effects of a high pressure treatment (0, 4, 6 min) on sliced ham, which is a typical meat product, at 600 MP a were tested for their effect on freshness. Moisture contents varied from 48 to 69%, salinity varied from 1.07 to 1.11%, and the pH decreased from 6.4~6.5 to 6.1~5.15. However, there was no difference between the control and treatment groups. General bacteria stored at $20^{\circ}C$ after hyper-pressure treatment were found to have no significant microorganisms in all groups until 4 weeks. but exceeded $10^5$ in control group and HPP 6 min treatment group from 5 weeks, At week 7, it was found to exceed $10^6$. The results indicate it was not possible to ingest food in the 4-and 6 minute treatment groups. Coliform was not observed in all groups despite observing for a total of 7 weeks at $20^{\circ}C$ weight test. VBN, a method used to determine the protein freshness of meat, showed a VBN value of less than 1 mg% until the fourth week and a value of 1 to 2 mg% after 5 weeks. The TBA was used as an index of the degree of fat acidosis in the meat tissues. The results showed it was below 0.18 mgMA / kg until the end of 7 weeks; this value was within the range for fresh meat, and there was no difference in treatment group. In this experiment, deformation of the packaging material did not occur and no swelling occurred due to the generation of gas. It is believed that the basic preservation effect was achieved only by blocking with the air due to the close contact of the packaging material.

• The korean journal of orthodontics
• /
• v.33 no.2 s.97
• /
• pp.131-140
• /
• 2003

The purpose of this study was to evaluate clinical applications of electroplating method through investigation of the physical properties of orthodontic rectangular wires according to varying their cross section. For the study, it was accomplished to electroplate the 0.016-inched orthodontic rectangular stainless steel wire. The cross section of stainless steel orthodontic rectangular wire increased from $0.016{\times}0.016inch\;to\;0.017{times}0.017inch$ by electroplating. The wire was heat treated to improve an adhesion between the wire and electroplated metal. h three-point bending test and torsion test were conducted in order to compare physical properties among three wire groups; $0.016{\times}0.016wires(group 016),\; electroplated\;0.016{\times}0.016wires(group\;016P)\;and\;0.017{\times}0.017$ wires (group 017). Through the investigations of each wire group, following results were obtained 1. At three-point bending test, the group Ol6P showed higher tendency in the degree of stiffness, yield strength and ultimate tensile strength than the group 016. Stiffness and ultimate tensile strength showed statistically significant differences between two groups at three-point bending test (p<0.05). 2. Stiffness, yield strength, and ultimate tensile strength of the group 016P showed lower tendency than those of the group 017 Stiffness showed statistically significant differences between two groups at three-point bending test (p<0.05). 3. Torque/twist rate, yield torsional moment, and ultimate torsional moment of the group 016P showed higher tendency than those of the group 016. All measurements showed statistically significant differences between two groups alter torsion test (p<0.05). 4. Torque/twist rate, yield torsional moment, and ultimate torsional moment of the group 0166P showed lower tendency than those of the group 017. Yield torsional moment, and ultimate torsional moment showed statistically significant differences between two groups after torsion test (p<0.05).

• The korean journal of orthodontics
• /
• v.33 no.2 s.97
• /
• pp.121-130
• /
• 2003

The purpose of this study was to evaluate the possibile clinical application of electroplating to increase diameter of an orthodontic wire, through examining the change of physical properties. The diameter of stainless steel orthodontic wire was increased from 0.016 inch to 0.018 inch by electroplating in a bath of nickel sulfate 100g/L, nickel chloride 60g/L, boric acid 30g/L, and sodium chloride 50g/L, under the conditions of 1.7V, $25\~29^{\circ}C\;and\;3.1\~3.3pH$. During the electroplating, the rate of diameter increase was measured every minute. To investigate uniformity, the diameter was measured at three different locations of each wire specimen aster electroplating. An X-ray diffraction test was performed to analyze the nature of the electroplated metal. Following heat treatment to improve adhesion between the wire and electroplated metal, a three-point bending test was conducted to compare stiffness, field strength, and ultimate strength among four wire groups; 0.016 inch, electroplated 016, electroplated and heat-treated 016, and 0.018 inch wires. Through the comparison of each wire group, following results were obtained. 1. In the load-deflection graph, the curve of the electroplated group was Placed between that of the 0.016 inch group and the 0.018 inch group, and the owe was closer to the 0.018 inch group by heat treatment. 2. In the electroplated and heat-treated 016 wire group, the values of stiffness, yield strength and ultimate strength showed higher tendency than in the original 0.016 Inch group. Stiffness and ultimate strength showed statistically significant differences between two groups. 3. Stiffness, yield strength, and ultimate strength of electroplated wire presented lower values than those of 0.018 inch wire group. 4. Stiffness, yield strength, and ultimate strength of electroplated and heat-treated wire showed higher tendency than those of electroplated wire group, and ultimate strength showed statistically significant difference between two groups. 5. After electroplating, the difference in diameter between the three locations was within $0.1\~0.3\%$ variation, and showed no statistical significance.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.37 no.4
• /
• pp.72-85
• /
• 2009

This study attempts to examine the principles of landscape composition for a 'Suhwon(書院)' and the meaning and value of its traditional landscape architecture, in order to apply the results to the design of modern landscape architecture. A 'Suhwon' is a vital space containing the form and meaning of human activity. This study analyzes the characteristics of landscape composition in the construction of the Namgea Suhwon, located in Hamyang, by examining the form and meaning of its area and composition. The Namgea Suhwon was constructed with a suitable configuration and harmony in a good location, neither field nor mountain, and which encompasses transcendence and a return after passage through a period of birth and abundance. Its appearance means 'life existence and hidden death(生居死幽)'. Its spatial system is a reflection of the idea of Samshinoje(三神五帝: The three abilities of Providence and its five subjects) connected with Ilsangje -Samshin -Ohje. It was built based on the idea of Biryebudong(非禮不動) meaning that one should follow only good decorum and avoid discourtesy, complying with "the frame of decorum" developed by the family rites of Chu Hsi. The environmental design of the Namgea Suhwon was interrupted by the material confrontation between mountains and water and a binary code system, such as front to rear, length to breadth, and movement to stillness. The design did not adhere to stiff axes, but pursued the harmonic principles of asymmetric balance in the building and the yard, which are very naturalistic. The name 'Namgea Suhwon' is closely related with the view of placement(置) and harmony(和), which are unified with the function and meaning formed by connecting Sung Confucianism with the Pungsu-Sasinsa structure in the layout of the grounds. When examining the D/H ratio of the building and yard, it can be seen that the spaces of Ganghak, Yusang and Jehyang were built appropriately, according to the natural characteristics of each space, such as a sense of openness, enclosure, tension, relief, enhancement, and hierarchical order. The spaces also reflect human scale concepts that take advantage of auditory features. The transition process after the construction of 'Namgea Suhwon' reveals the intentions of the builder to create an ecological landscape composition based on Placement and Harmony. Placement embodies' a purposeful space in which nature and the building are connected naturally, 'incomplete open space pursuing completion', and 'potential beauty in which tension and relaxation are repeated'. Harmony embodies 'order and continuity having a sense of unity with the natural environment' and the 'sharing of daily life and memory'. 'Namgea Suhwon' contains many ideas for landscape planning, land use and the design of a campus environment.

• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.877-887
• /
• 1996

The ideal membranes for membrane-covered oxygen probes system should be selectively permeable for oxygen and chemically inert, and have good mechanical strength. Polysulfone(PSf) was selected to develop the membrane for membrane-covered oxygen electrodes system. PSf membranes have properties such as good reproducibility, good mechanical strength, chemical inertness, and high heat resistance. PSf membranes were cast from polymer solution on the glass plate at constant temperature, and casting solvents used were tetrahydrofuran(THF), methylene chloride, and N-methyl-2-pyrrolidone(NMP). Tricresyl phosphate(TCP) as plasicizer was added to PSf to increase the softness of membrane. The permeation characteristics were observed for pure oxygen and nitrogen through pure PSf membranes by variable volume method and membrane-covered electrode system. The permeability coefficients of oxygen and nitrogen measured by variable volume method were slightly decreased with increasing of upstream pressure. The permeation properties of PSf membrane using methylene choride as casting solvent were not affected by the PSf amount of polymer solution. The permeability coefficients of oxygen and nitrogen for PSf membrane containing TCP were very slightly lower than those for pure PSf membrane, but ideal separation factors were slightly higher. The flexibility of PSf membrane containing 2wt% TCP was better than that of pure PSf membrane. It was expected that this increase in flexibility would solve the difficulty of fixing the membrane to the cathode. The membrane-covered oxygen probes system was composed of anode, cathode and electrolyte. The type of the anode was Ag/AgCl half-cell, that of cathode was Ag, and the electrolyte was 4N KCl solution. The result of sampled current voltametry for PSf membrane showed the plateu region at -0.3V~-1.0V. The correlation coefficient of oxygen partial pressure versus current for PSf membrane was relatively high, 0.99949. It was concluded that PSf membrane was the good candidate for the membrane-covered oxygen probes system.

• Journal of Sericultural and Entomological Science
• /
• v.37 no.1
• /
• pp.74-85
• /
• 1995

A study was conducted to provide some basic data for controlling the Mulberry scale insect(Pseudaulacaspis pentagona T.). Experiments were carried out with checking their field-life, and a few selected insecticides were tested when mulberry leaves were not in use. About 57% of female were survived from the overwintering attached to the bark. Over 80% of the scale were distributed within the range of 30cm from the base of each stem. One hundred percent and 96.7% of eggs were hatched under 25$^{\circ}C$ and 27$^{\circ}C$ respectively. Eighty percent of pupae emerged both under 25 and 27$^{\circ}C$. The Mulberry scale require about 33 days under 25$^{\circ}C$ and 30 days under 27$^{\circ}C$. This species had 2 generations each year in mulberry field in Suwon. Overwintered as a mated female only. Oviposited about 170 eggs under their scale starting from the late April (in 1994) through the mid May (in 1993). Phenthoate EC sprayed in the mid June against the larvae was very effect with over 96% of control value.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.13 no.3
• /
• pp.81-85
• /
• 2009

Purpose: The examination of nuclear medicine observes the change in accordance with the time elapsed in the same region purposed and there are many examinations to acquire the image during the same term. At this time, the same parameter should be applied. The hepatobiliary scan, lung scan etc, are the acquired examination in the divided time with a regular term. Pre-set time that is applied in continued next image is set in order to acquire the fixed counts. The same scan time should be applied for each image. This study will look for the rational plan and analyze the change of scan time in accordance with the time of the decision of scan time at examination that pre-set time is applied. Methods: The hapatobiliary scan that use the radio pharmaceutical $^{99m}Tc$-mebrofenin is choosed as compensation from Jan. 2009 to Mar. 2009 in the department of nuclear medicine in ASAN MEDICAL CENTER. Scan is started after 5 minutes from when 222 MBq (6 mCi) is injected to patient. We let patient stand up between both detectors, and possibly close to the front of detector. When scan time reach 10%, 25%, 50%, 75% of total scan time, we measured the expected total scan time. After finishing all of scan, we compared the total scan time and the expected total scan time, while image is acquiring. and we observed the change of scan time in accordance with radio activity by using phantom. Results: After starting scan, a difference of when scan time reach 10%, 25%, 50%, 75% of total scan time is that the biggest difference is 5 seconds on 10%. There statistically is difference between 25% (t:2.88, p<0.01) and 50% (t:2.05, p<0.01). Conclusions: When the same the scan time is applied in the examination that acquire the many frame, concluding the same scan time has a important effect on a quantitative analysis. Although method that decide the scan time after finish all of the examinations, there is a few problem to apply practical affairs. This may cause an inaccurate result on the examination that need a quantitative analysis. We think that operator should try to improve it. At least, after reach 50% of total scan time, deciding the total scan time mean that you can minimize error of a quantitative analysis caused by unmatched scan time from a gap of image.

• The Journal of the Petrological Society of Korea
• /
• v.11 no.3_4
• /
• pp.234-249
• /
• 2002

The Miwon-Boeun area in the central and northern part of Okcheon metamorphic zone, Korea, is composed of Okcheon Supergroup and Mesozoic Cheongju and Boeun granitoids which intruded it. The Okcheon Supergroup consists mainly of quartzite (Midongsan Formation), meta-calcareous rocks (Daehyangsan Formation, Hwajeonri Formation), meta-psammitic rocks (Unkyori Formation), meta-politic rocks (Munjuri Formation), meta-conglomeratic rocks (Hwanggangni Formation) in the study area, showing a zonal distribution of NE trend. Its' general trend is locally changed into NS to EW trend in and around high-angle fault of NS or NW trend. This study focused on deformation history of the Okcheon Supergroup, suggesting that the geological structure was formed at least by four phases of deformation. (1) The first phase of deformation occurred under ductile shear deformation of top-to-the southeast movement, forming sheath fold or A-type fold, asymmetric isoclinal fold, NW-SE trending stretching lineation. (2) The second phase of deformation took place under compression of NW-SE direction, forming subhorizontal, tight upright fold of M trend in the earlier phase, and formed semi-brittle thrust fault (Guryongsan Thrust Fault) of top-to-the southeast movement and associated snake-head fold in the later phase. (3) The third phase of deformation formed subhorizontal, open recumbent fold through gravitational or extensional collapses which might be generated from crustal thickening and gravitational instability. (4) The fourth phase of deformation formed moderately plunging, steeply inclined kink fold related to high-angle faulting, being closely connected with the local change of NE-trending regional foliation into NS to EW direction of strike in the vicinity of the high-angle fault.

• Journal of Chest Surgery
• /
• v.37 no.6
• /
• pp.467-473
• /
• 2004

Background: The sinus conversion rate after the maze procedure in chronic atrial fibrillation using radiofrequency energy is lower than with either conventional 'cut and saw' technique or cryothermia. The creation of incomplete transmural lesions due to poor tissue-catheter contact is thought to be the main cause. To address this problem, the current study was aimed to evaluate the effectiveness of a specially constructed compression device designed to enhance tissue catheter contact during unipolar radiofrequency catheter ablation. Material and Method: Circum-ferential right auricular epicardial lesions were created with a linear radiofrequency catheter in 10 anesthetized pigs. A device specially designed to increase contact by compression of the catheter to the atrial wall was used in 5 pigs (study group). This device was not used in the control group (5 pigs). Conduction block across the right auricular lesion was assessed by pacing, and the transmurality of the lesions were confirmed by microscopic examination. Result: Conduction block was observed in a total of 8 pigs; 5 in study group and 3 in control group. Transmural injury was confirmed microscopically by the accumulation of acute inflammatory cells and loss of elastic fibers in the endocardium. In two pigs with failed conduction block, microscopic examination of the endocardium appeared normal. Conclusion: Failed radiofrequency ablation is strongly related to non-transmural energy delivery. The specially constructed compression device in the current study was successful in creating firm tissue-catheter contact and thereby generating transmural lesions during unipolar radiofrequency ablation.

• Development and Reproduction
• /
• v.12 no.1
• /
• pp.19-30
• /
• 2008

Proper development of fertilized oocyte to blastocyst is a key step in mammalian development to implantation. During development of preimplantation embryos, the mammalian embryo needs supply the energy substrate for keep viability. Usually mammalian oocyte get substrate especially energy substrate from oviduct and uterus, because it does not store much substrate into cytoplasm during oogenesis. Carbohydrates are known as a main energy substrate for preimplantation stage embryos. Glucose, lactate and pyruvate are essential component in preimplantation embryo culture media and there are stage specific preferences to them. Glucose transporter and $H^+$-monocarboxylate cotransporter are a main mediator for carbohydrate transport and those expression levels are primarily under the control of intrinsic or extrinsic factors like insulin and glucose. Other organic substances, amino acids, lipids and nucleotides are used as energy substance and cellular regulation factor. Though since 1960s, successful development of fertilized embryo to blastocyst has been accomplished with chemically defined medium for example BWW and give rise to normal offspring in mammals, the role of metabolites and the regulation of intermediary metabolism are still poorly understood. Glucose may permit expression of metabolic enzymes and transporters in compacting morula, capable of generating the energy required for blastocyst formation. In addition, it has been suggested that the cytokines can modulate the metabolic rate of carbohydrate in embryos and regulate the preimplantation embryonic development through control the metabolic rate. Recently we showed that lactate can be used as a mediator for preimplantation embryonic development. Those observations indicate that metabolites of carbohydrate are required by the early embryo, not only as an energy source, but also as a key substrate for other regulatory and biosynthetic pathways. In addition metabolites of carbohydrate may involve in cellular activity during development of preimplantation embryos. It is suggested that through these regulation and with other regulation mechanisms, embryo and uterus can prepare the embryo implantation and further development, properly.