• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.3
• /
• pp.51-57
• /
• 2010

A dual-mode direct conversion receiver is developed in $0.13\;{\mu}m$ RF CMOS process for IEEE 802.11n based wireless LAN and IEEE 802.16e based mobile WiMAX application. The RF receiver covers the frequency band between 2.3 and 2.7 GHz. Three-step gain control is realized in LNA by using current steering technique. Current bleeding technique is applied to the down-conversion mixer in order to lower the flicker noise. A frequency divide-by-2 circuit is included in the receiver for LO I/Q differential signal generation. The receiver consumes 56 mA at 1.4 V supply voltage including all LO buffers. Measured results show a power gain of 32 dB, a noise figure of 4.8 dB, a output $P_{1dB}$ of +6 dBm over the entire band.

• Journal of Environmental Impact Assessment
• /
• v.29 no.3
• /
• pp.182-197
• /
• 2020

This study investigated the home range and characteristics of activities to contribute to the improvement of management techniques and the successful promotion of management policies of invasive nutria, which is a representative invasive species of South Korea. Six individuals were captivated for the study. Remote radio tracking on three of them was carried out followed by the analysis of the results. The average home range of the follow-up individuals were confirmed to be 0.043 ㎢ at MCP 95%, 0.085 ㎢ at K 95%. It was 0.018 ㎢ at K 50%, which is the core space. In 95% MCP, males exhibited the home range with 0.058 ㎢, showed wider home range 0.046 ㎢ than females who showed 0.012 ㎢, and showed a wider home range 0.015 ㎢ more at night than during the day. As a result of comparing the results of this study with the case studies of overseas studies, it is determined that the magnitude of the derived home range is the result of a stable habitat in which the procurement of food resources is smooth and human interference is limited. The daily moved distance of males was larger than that of females, with a maximum moved distance of 1,278 m per day. Activity at the study site is high from around sunset to around 6 A.M., 10 P.M., 7 P.M., 1 A.M., and 5 A.M., and high around sunrise and low during the daytime such as 2 P.M., which reflected the propensity of nocturnal animals to act. The results of this study on the home range and activity in nutria can be used as useful data forimproving the management of invasive alien species for the installation and operation of traps, the spatial setting of controlled areas, and the calculation of the amount ofresources together with a basic understanding of nutria's behaviors in South Korea.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.1
• /
• pp.19-25
• /
• 2008

In this paper, the front end module (FEM) was proposed for 2.4GHz WLAN band by LTCC multilayer application. The FEM was composed of power amplifier IC, switch IC, and LTCC module. LTCC module consists of output matching circuit and lowpass filter as Tx part, bandpass filter as Rx part. Design of output matching circuit for LTCC was used matching parameter from output matching circuit based on lumped circuit on the PCB board. The dielectric constant of LTCC substrate is 9. The substrate was composed of total 26 layers with each 30um thickness. Ag paste was used for the internal pattern as the conductor material. The size of the module is $4.5mm{\times}3.2mm{\times}1.4mm$. The fabricated FEM showed the gain of 21dB, ACPR of less than -31dBc first side lobe and Less than -59dBc second side lobe and the output power of 23Bm at P1dB.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.6A
• /
• pp.634-639
• /
• 2006

In this paper an MMIC 2-stage power amplifier is designed and fabricated for 5GHz wireless LAN applications using $0.5{\mu}m$ gate length PHEMT transistors. The PHEMT gate width is optimized in order to meet the linearity and efficiency of the MMIC power amplifier. The $0.5{\mu}m\times600{\mu}m$ PHEMT for the drive stage and $0.5{\mu}m\times3000{\mu}m$ PHEMT for the amplification stage are the optimized sizes to achieve more than 25dBc of third order IMD at the power level of 3dB back-off from the input P1dB and more than 22dBm output power under a supply voltage of 3.3V. The two-stage MMIC power amplifier is designed to be used for the both of HIPERLAN/2 and IEEE 802.11a because of its broadband characteristics. The fabricated PHEMT MMIC power amplifier exhibits a 20.1dB linear power gain, a maximum 22dBm output power, a 24% power added efficiency under 3.3V supply voltage. The input and output on-chip matching circuits are included on a chip of $1400\times1200{\mu}m^2$.

• The KIPS Transactions:PartC
• /
• v.9C no.2
• /
• pp.293-296
• /
• 2002

UP Link is One of the commercial product which converts HTML to HDML convertor in order to show the internet www contents in the mobile environments. When UP browser accesses HTML pages, the agent in the UP Link controls the converter to change the HTML to the HDML, I-Mode, which is developed by NTT-Docomo of Japan, has many contents through the long and stable commercial service. Micro Explorer, which is developed by Stinger project, also has many additional function. In this paper, we designed and implemented WAP convertor which can accept C-HTML contents and mHTML contents. C-HTML format by I-Mode is a subset of HTML format, mHTML format by ME is similar to C-HTML, So the content provides can easily develop C-HTML contents compared with WAP and the other case. Since C-HTML, mHTML and WML are used under the mobile environment, the limited transmission capacity of one page is also similar. In order to make a match table. After that, we apply conversion algorithm on it. If we can not find matched element, we arrange some tags which only can be supported by WML to display in the best shape. By the result, we can convert over 90% contents.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.5
• /
• pp.49-54
• /
• 2009

This paper describes implementation of the 1.9GHz RF frequency synthesizer with $0.18{\mu}m$ silicon CMOS technology being used as an application of the USN sensor node transceiver modules. To get good performance of speed and noise, design of the each module like VCO, prescaler, 1/N divider, fractional divider with ${\Sigma }-{\Delta}$ modulator, and common circuits of the PLL has been optimized. Especially to get good performance of speed, power consumption, and wide tuning range, N-P MOS core structure has been used in design of the VCO. The chip area including pads for testing is $1.2{\times}0.7mm^2$, and the chip area only core for IP in SoC is $1.1{\times}0.4mm^2$. The test results show that there is no special spurs except -63.06dB of the 6MHz reference spurs in the PLL circuitry. There is good phase noise performance like -116.17dBc/Hz in 1MHz offset frequency.

• 한국공간정보시스템학회:학술대회논문집
• /
• 2002.03a
• /
• pp.83-88
• /
• 2002

최근 들어 무선인터넷 및 모바일 컴퓨팅 기술의 급속한 발전과 함께 향후 그 수요가 증대될 것으로 예상되는 분야가 위치기반 서비스(LBS: Location Based Service) 기술이다. 위치기반 서비스는 이동 통신을 통하여 사람 및 사물의 위치를 파악하고 이를 활용한 부가 응용 서비스로 국가 정보기술 인프라의 주요 영역을 점유하고 있는 GIS의 차세대 핵심 기술로 발전이 예상되는 분야이다[3][4]. 현재 3GPP나 3GPP2, OGC, LIF와 같은 여러 표준화 기구 및 산업체에서 위치기반 서비스와 이를 위한 시스템에 대한 연구가 진행중이며 위치기반 서비스를 위한 데이터 모델 표준화 연구는 거의 이루어지지 않고 있는 상황이다. 위치기반 서비스를 위한 데이터 표준화 모델은 이미 구축된 공간 데이터베이스의 재사용과 위치기반 서비스들간의 상호 운용성을 지원할 수 있어야 한다. 본 연구에서는 위치기반 서비스들 간의 상호 호환 및 통합을 가능하게 하고, 기존 공간데이터베이스와 연계하여 이 데이터를 위치기반 서비스에 활용하기 위한 공간 데이터 표준화 모델을 제안하고자 한다. 이를 위해 위치기반 서비스 표준화 사례를 조사하고, 위치기반 서비스를 위한 공간 데이터 모델을 제시하였다. 본 연구에서는 OpenLS의 위치기반 서비스를 기본서비스로 하고, OpenGIS의 공간 데이터 모델을 기반으로 네 가지 기본 위치 데이터 타입과 모델의 요구 사항을 포함하는 공간 데이터 표준모델을 개발하였다. 위치기반 공간 데이터 표준 모델은 위치기반 서비스와 데이터들과의 연계를 쉽게 하고, 위치기반 서비스들 간의 상호 운용성을 높이며, 기존 사용자 시스템의 수정 없이 인터페이스만을 추가함으로써 표준을 수용할 수 있다.\pm}153.2,\;116.1{\pm}94,\;29.4{\pm}30.3,\;45.1{\pm}44$로 Mel 10군과 Mel 30군이 유의적인 감소를 보였으나(p<0.05) 이들 두 군 간의 차이는 나타나지 않았다. 이상의 결과로, 랫트에서 복강수술 후 melatonin 10mg/kg투여가 복강 내 유착 방지에 효과적이라고 생각된다.-1}{\cdot}yr^{-1}$로서 두 생태계에 축적되었다.여한 3,5,7군에서 PUFA 함량이 증가한 반면, SFA 함량은 감소하여 P/S 비율, n-3P/n-6P 비율은 증가하는 경향이었으며 이는 간장의 인지질, 콜레스테롤 에스테르, 총 지질의 지방산조성에서도 같은 경향을 볼 수 있었다.X>$(C_{18:2})$와 n-3계 linolenic acid$(C_{18:3})$가 대부분을 차지하였다. 야생 돌복숭아 과육 중의 지방산 조성은 포화지방산이 16.74%, 단불포화지방산 17.51% 및 다불포화지방산이 65.73%의 함유 비율을 보였는데, 이 중 다불포화지방산인 n-6계 linoleic acid$(C_{18:2})$와 n-3계 linolenic acid$(C_{18:3})$가 지질 구성 총 지방산의 대부분을 차지하는 함유 비율을 나타내었다.했다. 하강하는 약 4일간의 기상변화가 자발성 기흉 발생에 영향을 미친다고 추론할 수 있었다. 향후 본 연구에서 추론된 기상변화와 기흉 발생과의 인과관계를 확인하고 좀 더 구체화하기 위한 연구가 필요할 것이다.게 이루어질 수 있을 것으로 기대된다.는 초과수익률이 상승하지만, 이후로는 감소하므로, 반전거래전략을 활용하는 경우 주식투자기간은 24개월

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.42 no.3
• /
• pp.464-477
• /
• 2013

There is a great need to develop a training program proven to change behavior and improve knowledge. The purpose of this study was to evaluate employee hygiene knowledge, hygiene practice, and cleanliness, before and after HACCP system implementation at one small-size restaurant. The efficiency of the system was analyzed using time-temperature control after implementation of u-HACCP$^{(R)}$. The employee hygiene knowledge and practices showed a significant improvement (p<0.05) after HACCP system implementation. In non-heating processes, such as seasoned lettuce, controlling the sanitation of the cooking facility and the chlorination of raw ingredients were identified as the significant CCP. Sanitizing was an important CCP because total bacteria were reduced 2~4 log CFU/g after implementation of HACCP. In bean sprouts, microbial levels decreased from 4.20 logCFU/g to 3.26 logCFU/g. There were significant correlations between hygiene knowledge, practice, and microbiological contamination. First, personnel hygiene had a significant correlation with 'total food hygiene knowledge' scores (p<0.05). Second, total food hygiene practice scores had a significant correlation (p<0.05) with improved microbiological qualities of lettuce salad. Third, concerning the assessment of microbiological quality after 1 month, there were significant (p<0.05) improvements in times of heating, and the washing and division process. On the other hand, after 2 months, microbiological was maintained, although only two categories (division process and kitchen floor) were improved. This study also investigated time-temperature control by using ubiquitous sensor networks (USN) consisting of an ubi reader (CCP thermometer), an ubi manager (tablet PC), and application software (HACCP monitoring system). The result of the temperature control before and after USN showed better thermal management (accuracy, efficiency, consistency of time control). Based on the results, strict time-temperature control could be an effective method to prevent foodborne illness.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.45 no.6
• /
• pp.87-93
• /
• 2008

This paper describes implementation of the 5.0GHz RF frequency synthesizer with $0.18{\mu}m$ silicon CMOS technology being used as an application of the IEEE802.15.4 USN sensor node transceiver modules. To get good performance of speed and noise, design of the each module like VCO, prescaler, 1/N divider, fractional divider with ${\Sigma}-{\Delta}$ modulator, and common circuits of the PLL has been optimized. Especially to get good performance of speed, power consumption, and wide tuning range, N-P MOS core structure has been used in design of the VCO. The chip area including pads for testing is $1.1*0.7mm^2$, and the chip area only core for IP in SoC is $1.0*0.4mm^2$. Through comparing and analysing of the designed two kind of the frequency synthesizer, we can conclude that if we improve a litter characteristics there is no problem to use their as IPs.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.4 s.346
• /
• pp.75-80
• /
• 2006

This paper has proposed a novel dual band transmitter module which can be operating either as an amplifier or as a frequency multiplier according to the input frequency. A conventional dual band transmitter consists of separate amplifiers operating at each frequency band, but the proposed dual band module operates as an amplifier for the IEEE 802.11b/g signal, and as a frequency doubler for the IEEE 802.11a signal according to input frequency and bias voltage. In this paper, we have obtained sharp stop band characteristics by using microstrip DGS(Defected Ground Structure) to suppress the fundamental frequency of the frequency doubler as well as the second harmonic of the amplifier. From measurement result, second harmonic suppression is below -59dBc in the amplifier mode, and fundamental suppression is below -35dBc in the frequency doubler mode. And the designed module has 17.8dBm output P1dB at 2.4GHz and 10.1dBm power for 5.8GHz output, and the output power in the two modes are 0.8dB and 2.8dB larger than the module with ${\lambda}g/4$ reflector, respectively.