• Fire Science and Engineering
• /
• v.33 no.4
• /
• pp.70-76
• /
• 2019

This paper reports development of a low-power standalone heat detector using a Critical-Temperature Switch. The Critical-Temperature Switch, which is a thermally sensitive and passive component whose resistance decreases significantly at 70 ℃ due to a metal-insulator transition, provides reliable temperature measurements. This digital-like behavior of the Critical-Temperature Switch can detect fires without a microcontroller, meaning that it can minimize the power consumption of the standalone heat detector. The experimental results showed that the standalone heat detector using the Critical-Temperature Switch complied with the Notification of the National Emergency Management Agency. Compared to conventional standalone heat detectors, only 70% of the power was consumed monitoring the fires.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.5
• /
• pp.648-658
• /
• 1998

In this paper, the effect of the gap in the ground plane on the electromagnetic interference (EMI) is analyzed quantitatively. Because of a lot of advantages compared to other numerical techniques, the FDTD (finite difference time domain) is applied to the EMI effect modeling. The analyzed model is the simplified PCB (printed circuit board) which has a microstrip and ground plane. The inductance induced by the gap is modeled and calculated by gridding the whole PCB based on the FDTD algorithm. When external cables are attached to the PCB, the common-mode current is induced along the attached cable and the resulting electric field strength is calculated and presented along with the FCC and CISPR EMI limits. The results show that the radiated field strength highly depends on the size of the ground plane gap. The numerical simulation results can be used as a reference in the practical PCB design with the ground plane gap.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.11
• /
• pp.831-835
• /
• 2013

In this study, we fabricated a micro $Pb(Zr,Ti)O_3$ (PZT) film piezoelectric cantilever with a Si proof mass and dual beams through MEMS process. The size of the beam and the integrated Si proof mass were about $4,320{\mu}m{\times}290{\mu}m{\times}12{\mu}m$ and $1,380{\mu}m{\times}880{\mu}m{\times}450{\mu}m$ each. To reduce the air damping and have the larger displacement of dual beams was used for design. After mounting micro PZT film piezoelectric cantilever on shaker, we measured the resonance frequency and a output voltage while making resonant frequency changed. The resonant frequency and the highest average power of the cantilever device were 110.2 Hz and 0.36 ${\mu}W$ each, at 0.8 g acceleration and 23.7 $k{\Omega}$ load resistance, respectively.

• Journal of IKEEE
• /
• v.17 no.2
• /
• pp.140-144
• /
• 2013

This paper presents the novel design of circular polarized Ka-band horn array antenna. The element antenna of the arrya is composed of two parts, microstrip patch and square horn, and the microstrip patch is fed by corner truncated microstrip patch for circular polarization. The patch antenna has the role of a feeder and polarizer of the horn, thus the whole size of the horn antennae can be considerably reduced. The $1{\times}8$ horn array was designed and fabricated by the spacing of $0.9{\lambda}_0$ among the element horn. The element horn has typical gain of 8dBi and axial-ratio bandwidth of 4.9% at 3dB, and the minimum gain and axial-ratio bandwithd of the array is 14dBi and 8.2%.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.5
• /
• pp.105-113
• /
• 2009

In this paper, a vehicle antenna for AM, FM, TDMB, GPS systems was designed and implemented. AM antenna loaded into small space of shark shape was designed by ferrite turn style antenna. For the FM and TDMB antenna, folded monopole antenna which helical is folded was applied. GPS antenna for achieving characteristics both bandwidth and gain improvement was designed microstrip patch that has air substrate and fractal structure. Receiving signal strengths by the measurement were presented for the AM, FM and TDMB antenna. AM signal strength was -65.7dBm, this strength is almost as same conventional pole antenna as -63.4dBm. It can be replaced conventional pole or glass antenna by the studied antenna. Signal strengths for FM and TDMB were -55.66 and -43.50dBm at center frequency, they are 5~10dB higher than conventional antenna. Measurements of bandwidth and gain for the GPS antenna showed 135 MHz under VSWR 2 : 1 and 4.31dBi, gains over GPS band were 3~5dB higher than ceramic patch antenna.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.7
• /
• pp.81-88
• /
• 2004

In case of mechanical down tilting, a horizontal pattern is distorted and beam width widens whenincreasing tilt angle, which causes an expansion of hand off region and burden base station equipment. In contrast, electrical down tilting has advantage that horizontal HPBW is kept constant with down tilting. In this paper, based on a phased array technology, dual polarized base station antenna with electrical down tilting was developed at 800MHz band. The antenna has down tilting range of 0$^{\circ}$ to 14$^{\circ}$, and 15㏈i gain. We use stacked microstrip patch as a radiated element and apply balanced feed technique to improve isolation between ports and discrimination of cross polarization. The effect of electrical down tilting was verified by field test.

• KSBB Journal
• /
• v.22 no.6
• /
• pp.433-437
• /
• 2007

A constant desire has been to fabricate nanopatterns for biochip and the Ultraviolet-nano imprint lithography (UV-NIL) is promising technology especially compared with thermal type in view of cost effectiveness. By using this method, nano-scale to micro-scale structures also called nanopore structures can be fabricated on large scale gold plate at normal conditions such as room temperature or low pressure which is not possible in thermal type lithography. One of the most important methods in fabricating biochips, immobilizing, was processed successfully by using this technology. That means immobilizing proteins only on the nanopore structures based on gold, not on hardened resin by UV is now possible by utilizing this method. So this selective nano-patterning process of protein can be useful method fabricating nanoscale protein chip.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.1
• /
• pp.25-33
• /
• 1998

In this paper, we describe a single-gate MESFET mixer at PCS(Personal Communication Service) frequency band. The PCS frequency band is 1965~2025 MHz in FR and 140 MHz in IF irrespectly. The design of the mixer was executed by microwave simulator, EEsof Libra. The matching network is consisted of rectangular inductor, MIM capacitor and open stub. The ma- nufacture work was accomplished by the micro-pen and wedge-bonder. The mixer showed $6.69\pm0.65$ dB of conversion gain, $-14.9\pm3.5$dB of RF reflection coefficient and 57.83 dB of LO/IF isolation at 10 dBm of LO power when LO frequency is 1855 MHz. When this mixer is used at PCS terminal, IF-amplifier which compensates the conversion loss of diode mixer may be omitted.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.8
• /
• pp.45-51
• /
• 2008

HID(High Intensity Discharge) search lamp for shipment requires a high open circuit and output current compare than vehicle. This paper presents a soft-start open circuit voltage and constant current sequence control method for 2.5[kW] HID search lamp. The proposed method controls the opal circuit voltage and discharge current of HID lamp according to ignition signal with a simple 8-bit micro-processor and PWM device. For the stable control of lamp, micro-processor checks the output voltage and current. And the checked signals are compared with ignition signal and changes the control mode for stable operation. An ignition signal and micro-processor change the control mode from open circuit voltage contort to constant current control. The proposed control scheme is verified from experimental tests of 2.5[kW] HID search lamp for shipment.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.9B
• /
• pp.1668-1675
• /
• 1999

In this thesis, a narrowband bandpass filter using HTS is proposed for the multiplexer of the satellite communication subsystems. The proposed structure using HTS provides the narrower band and the lower insertion loss characteristics than the conventional parallel-coupled-line bandpass filter. The filter structure using hairpin-line only cause the spurious modes due to the surface waves. But these modes can be lessened by using the hybrid hairpin-line/parallel-coupled-line proposed in this thesis. The narrowband bandpass filters using HTS at the operation frequency of 14.25 GHz are fabricated to have the narrow bandwidth less 1% and the insertion loss less 3dB in comparison with the normal metal microstrip filter with the same three poles. The experimental results show that the filter using HTS has the characteristics of the narrower bandwidth and less insertion loss and can be fabricated with more compact size in comparison with the bandpass filter using normal metal.