• Journal of Navigation and Port Research
• /
• v.37 no.2
• /
• pp.173-179
• /
• 2013

The interaction among wave, seabed and marine structure is an important issue in coastal engineering as well as geotechnical engineering. Understanding variations of stresses and pore water pressures generated in seabed induced by waves is important for civil engineers who have to design the foundation for various marine structures and verify the instability of seabed. In the matters on seabed instability, particularly, in the case of wave-induced liquefaction of seabed, it is turned out there are two different mechanisms through previous studies. These are caused by the transient or oscillatory nature and the residual or progressive nature of excess pore water pressure generated in seabed, respectively. In this study, it is analyzed dynamic characteristics of soils sampled in seabed around the port of Kochi, Japan, through the dynamic triaxial tests and the residual excess pore water pressure in the seabed induced by seepage force of wave. In addition, the calculated residual excess pore water pressures were compared with the field data observed in the port of Kochi.

• Journal of the Korean Institute of Gas
• /
• v.6 no.1 s.17
• /
• pp.1-9
• /
• 2002

This paper presents simple models for flow and the PIG dynamics when it passes through a $90^{\circ}$ curved section of pipeline. The simulation has been done with two different operational boundary conditions. The solution fur non-linear hyperbolic partial equations for flow is given by using MOC. The Runge-Kuta method is used to solve the initial condition equation fur flow and the PIG dynamics equation. The simulation results show that the proposed model and solution can be used fur estimating the PIG dynamics when the pig runs in the pipeline including curved section. In this paper, dynamic modeling and its analysis for the PIG flow through $90^{\circ}$ curved pipe with compressible and unsteady flow are studied. The PIG dynamics model is derived by using Lagrange equation under assumption that it passes through 3 different sections in the curved pipeline such that it moves into, inside and out of the curved section. The downstream and up stream flow dynamics including the curved sections are solved using MOC. The effectiveness of the derived mathematical models is estimated by simulation results fur a low pressure natural gas pipeline including downward and upward curved sections. The simulation results show that the proposed model and solution can be used for estimating the PIG dynamics when we pig the pipeline including curved section.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.7 no.4
• /
• pp.31-37
• /
• 2003

This paper presents the methodologies for seismic retrofitting of cabinet equipment which can be employed to resolve the USI A-46 problem related to seismic qualification of old nuclear power plant. To obtain accurate dynamic characteristics of a cabinet structure, three types of structural modeling are introduced and the their free vibration modes are compared. Three types of seismic retrofitting scenarios, such as 1) the installation of bracing, 2) installation of damper, 3) installation of tuned mass damper(TMD), are established and evaluated for the decrease of ICRS(In Cabinet Reponse Spectrum). In the cases of 1) ＆ 2), since the retrofitted structures show larger ICRS than that of the original structure, the careful considerations are need in the application of these methods. Though the installation of TMD shows the best retrofitting result, the construction of analysis model that indicate the accurate vibration modes of real structure is estimated the essential step of this retrofitting method.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.433-437
• /
• 2015

XP-SWMM은 유한차분방법에 의한 천수방정식을 기반으로 하는 TUFLOW 엔진을 탑재하여 1차원 솔루션 엔진과 동적으로 연결하여 범람원에서의 흐름거동을 2차원으로 해석할 수 있다. 유역에서 발생한 모든 유출량은 해당 소유역의 노드(맨홀)로 유입되며 2차원 침수양상은 관로상태에 따라 노드를 통해 역류한 유출수에 의해서 폰딩(Ponding)되는 조건으로 모의한다. XP-SWMM의 침수범람 모의는 침수범람 상황을 가시적으로 보여주는데 상당한 강점을 가지고 있으나 실제 지형여건에 따른 자연현상을 엄밀하게 모델링하는데 일정부분 한계가 있다. 모형의 한계는 담수된 노드의 수위로 인한 에너지 영향(오리피스 흐름)으로 인접관로의 침수가 부가적으로 유발할 수 있다는 점이며 실제 대부분의 경사지에서의 침수상황은 노드에 유출수가 담수되지 않고 하류로 지면을 따라서 확산(Diffusion)되어 담수영향으로 인한 인접관로 침수가 추가적으로 유발되지 않을 가능성이 매우 높다. 즉, XP-SWMM의 담수허용조건, 지반고 2D연결 옵션은 유역에서의 침수발생량을 과대평가 할수 있으며 특정 유역에서는 실제 침수발생 상황과 차이가 발생 할 수 있는 것이다. 본 연구에서는 서울시 광화문 일대의 효자배수분구 우수관로를 SWMM으로 구성하고 강우조건 95mm/hr에서 노드조건을 담수허용, 2D연결, 담수없음 조건으로 모형을 수행하여 침수모의 결과를 비교, 검토하였다. 전체관로 노드조건을 담수허용, 2D연결로 설정하게 되면 담수없음 조건과 비교하여 1.2-2.8배의 침수발생량이 추가로 발생하는 것으로 검토되었다. 즉, 담수없음 조건의 경우 침수발생시 노면 수위상승 인한 동수경사 영향이 반영된 압력관로 영향이 반영되지 않아 노드간 침수발생량이 중복되지 않는다. 반면, 담수허용이나 2D연결로 모형을 수행할 경우 지면의 경사가 충분히 있는 지역에 침수가 발생하더라도 일정 수심이상의 수두(동수경사선)가 형성되어 침수를 추가로 유발하는 것으로 보인다.

• Tribology and Lubricants
• /
• v.39 no.4
• /
• pp.154-166
• /
• 2023

This study establishes a numerical analysis model of the finite element overhung rotor supported by a DTRB and describes the stiffness properties of the DTRB. The vibration characteristics and contact pressure of the RBR system are predicted according to the DTRB support characteristics such as the initial axial compression and roller profile. The stiffness of the DTRB significantly varies depending on the initial axial compression and external load owing to the occurrence of rollers under the no-load condition and increase in the Hertz contact force. The increase in the initial axial compression increases the rigidity of the DTRB, thereby reducing the displacement of the RBR system and simultaneously increasing the natural frequency. However, above a certain initial axial compression, the effect becomes insignificant, and an excessive increase in the initial axial compression increases the contact pressure. The roller crowning radius, which gives a curvature in the longitudinal direction of the roller, decreases the displacement of the RBR system and increases the natural frequency as the value increases. However, an increase in the crowning radius increases the edge stress, causing a negative effect in terms of the contact pressure. These results show that the DTRB support characteristics required for reducing the vibration and contact pressure of the RBR system supported by the DTRB can be designed.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.12
• /
• pp.89-98
• /
• 2006

In this paper the behavior of saturated sand deposits where liquefaction occurred before is studied for successive earthquakes. The relationship between past pore pressure generation and reliquefaction resistance is examined by using cyclic direct simple shear tests. If the soil sample in direct simple shear produced nearly 90% of excess pore pressure during first time loading, its liquefaction resistance increased during following cyclic loading after consolidation. However, a fully liquefied soil during first time loading has a densely packed condition but shows less liquefaction resistance for the following cyclic loading. UBCSAND model that can account for pore pressure change and stiffness loss of soil during shaking is used to analyze the centrifuge test simulating reliquefaction. The pore pressure rise during first time cyclic loading controls liquefaction resistance. The measurements from reliquefaction centrifuge test are compared with numerical predictions. By considering frequent earthquakes having occurred at the Southern Korea near Japan, such effective stress approach is necessary for reliquefaction study.

• Journal of the Korea Concrete Institute
• /
• v.22 no.4
• /
• pp.535-546
• /
• 2010

Recently, the probability of collision accident between vehicles or vessels and infrastructures are increasing at alarming rate. Particularly, collision impact load can be detrimental to sub-structures such as piers and columns. The damaged pier from an impact load of a vehicle or a vessel can lead to member damages, which make the member more vulnerable to impact load due to other accidents which. In extreme case, may cause structural collapse. Therefore, in this study, the vehicle impact load on concrete compression member was considered to assess the quantitative design resistance capacity to improve, the existing design method and to setup the new damage assessment method. The case study was carried out using the LS-DYNA, an explicit finite element analysis program. The parameters for the case study were cross-section variation of pier, impact load angle, permanent axial load and axial load ratio, concrete strength, longitudinal and lateral rebar ratios, and slenderness ratio. Using the analysis results, the performance based resistance capacity evaluation method for impact load using satisfaction curve was developed using Bayesian probabilistic method, which can be applied to reinforced concrete column design for impact loads.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1993.04a
• /
• pp.86-92
• /
• 1993

자동차의 현가장치에 대한 능동제어연구는 국내외적으로 활발히 진행되어 왔다. 수동식현가장치는 단순히 스프링과 감쇠기로 차체의 진동을 수동 제어 하므로 성능 향상에 한계가 존재하게 된다. 수동식 현가장치가 강성계수와 감쇠계수를 조절함으로써 차체로 들어오는 진동을 억제하는 반면, 능동식제 어는 보통 유압을 이용하여 효율적으로 차체에 들어오는 진동을 억제시키게 된다. 일반적으로 자동차가 능동현가장치 설계시 요구되는 사항은 탑승자의 승차감, 조종성, 현가장치의 공간확보 문제, 경제성(제어력), 실제적으로 자동 차에 적용할 수 있는 능동제어기법인가 하는 문제이다. 자동차 능동식 현가 장치는 보통 1/4 car (2자유도계), Full-car 모델 (7자유도계) 등으로 모델링 을 하여 능동제어기를 설계한다. 1/4 car 모델의 특징은 해석이 비교적 단순 하고 현가장치의 동적거동을 이해하는데 유용하고 실험을 하거나 실제 자동 차에 적용하기 쉬운 반면에 Full-car 모델에 비해 제어력의 효율이 떨어진다 는 단점이 있다. 그 이유는 1/4 car 모델은 차체의 동역학적 특성을 고려하 여 설계하지 않았기 때문에 4개의 독립현가차축에서는 오직 그 현가축방향 으로 발생하는 수직방향의 진동만을 제어하기 때문이다. 따라서 동역학적 역 성에 기인하는 운동을 제어하는 비효율적인 제어력이 공급된다는 단점을 갖 는다. 이에 비해 full-car 모델은 주행모드(수직, 롤링, 피칭운동)간의 연성을 고려하여 제어기를 설계할 수 있기 때문에 1/4 car 모델에 비해 제어력의 효 율이 높다는 장점이 있는 반면에 모델이 수학적으로 복잡하므로 제어력을 구하는데 계산량이 많고, 실제 자동차에 적용하기에 복잡하다는 단점을 갖고 있다. 따라서 본 논문에서는 쉽게 실험할 수 있고, 실용화할 수 있는 1/4 car 모델에 대하여 능동제어기를 설계하여 실제자동차에 능동제어기를 적용할 때 참고가 될 수 있도록 하였다. 자동차는 저주파영역의 밴드통과필터 역할 을 하므로 저주파에서의 성능, 특히 탑승자가 민감하게 느끼는 0.5Hz - 10Hz 부근의 주파수성능은 승차감, 조종성에 상당히 중요하다. 이에 본 논문 에서는 0.5Hz - 10Hz 부근의 승차감, 조종성의 향상에 초점을 두고 차체의 속도를 출력변수로 한 LQG/LTR 제어기를 설계하였다. LQG/LTR 설계기법 은 안정도-강인성이 좋은 체계적인 설계기법으로서 전 상태를 측정할 필요 가 없으므로 실제 적용시 효과적이다. 또한 자동차의 제원의 변화에 대한 고 유치의 민감도해석과 새로운 개념으로 안정도-강인성(Robustness)해석을 하 여 수동시스템과 능동시스템의 강인성을 비교하였다.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.54 no.4
• /
• pp.39-46
• /
• 2017

Jack-up drilling rigs are widely used in offshore oil and gas exploration industry. It is originally designed for use in the shallow waters less than 60m of water depth; there is growing demand for their use in deeper water depth over 150m and harsher environmental conditions. In this study, global in-place analysis of jack-up rig leg for North-sea oil well is performed through numerical analysis. Firstly, environmental conditions and seabed characteristics at the North-sea are collected and investigated measurements from survey report. Based on these data, design specifications are established and the overall basic design is performed. Dynamic characteristics of the jack-up rig for North-sea are considered in the global in-place analysis both leg and hull and the basic stability against overturning moment is also analyzed. The structural integrity of the jack-up rig leg/hull is verified through the code checks and the adequate safety margin is observed. The uncertainty in jack-up behaviour is greatly influenced by the uncertainties in the soil characteristics that determine the resistance of the foundation to the forces imposed by the jack-up structure. Among the risks above mentioned, the punch-through during pre-loading is the most frequently encountered foundation problem for jack-up rigs. The objective of this paper is to clarify the detailed structure and installation engineering matters for prove the structural safety of jack-up rigs during operation. With this intention the following items are addressed; - Characteristics of structural behavior considering soil effect against environmental loads - Modes of failure and related pre-loading procedure and parameters - Typical results of structural engineering and verification by actual measurement.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.40 no.3
• /
• pp.214-224
• /
• 2004

A large cage system for the purpose of fishes farming in the open sea was influenced by various forces from the ocean environment. The deformation of the cage by these forces affects the safety of the cage itself, as well as that of the cultivated creatures. In this research, theoretical model was established to analyzing dynamic movement influenced by current for cage. Also, to increase the accuracy of calculations, the reduction ratio of flow speed acquired using the flume tank experiment. Applying the reduction ratio of flow speed to the numerical calculation, the calculation values were compared with the measured values in the flume tank experiment using cage model. The results were as follows ; 1. When the flow speed of the flume tank is fixed, the decrease of the velocity of flow which is passed the upper panel side is proportion to the increase of porosity ratio of netting. 2. When the porosity ratio is fixed, the increase of the velocity of flow which is passed the upper panel side is proportion to the increase of velocity of flow. 3. When the porosity ratio and the flow speed of the flume tank are fixed, the decrease of the velocity of flow which is passed the upper panel side is proportion to the increase of attack angle. 4. As a result of comparison between the underwater shape by simulation which is applying the reduction ratio of flow speed from the experiment using plane netting and that by model experiment, it was found out that the result of the simulation was very close to that of model gear within ${\pm}$ 5 % error range.