• Explosives and Blasting
• /
• v.37 no.2
• /
• pp.1-13
• /
• 2019

In this study, Rock deformation on the splitting surface was investigated by using the finite element code relating to the blasting in urban area. The maximum principal strain according to the blasting detonation pattern was analyzed by the modeled blast section, and deformation of the splitting surface formed by the numerical analysis and the real blasting were compared. As a result, it was found that the maximum principal strain was observed a difference according to the blasting detonation pattern on the splitting surface, and the splitting surface was showed a similar waveform both the numerical analysis and the real blasting.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.11 no.4
• /
• pp.17-26
• /
• 1991

Numerical methods are developed to obtain the critical loads and to analyze the post-buckling behaviour of the linearly varying tapered columns. The non-dimensional differential equations governing the elastica of post buckled column are derived by third order and solved numerically using the Runge-Kutta method and Regula-Falsi method. Three kinds of cross-sectional shape with simply supported end constraint are applied in unmerical examples. As the numerical results, the equlibrium paths. the typical elastica of post buckled columns and the critical load vs. section ratio curves are presented in figures. Also, the effects of cross-sectional shape factor on critical loads and postbuckling behaviour are presented in tables.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.10
• /
• pp.845-855
• /
• 2018

Cross section design of a prop-blade is carried out for VTOL(Vertical Takeoff and Landing) Quad Tilt Prop-rotor UAV with a maximum takeoff weight of 55 kg and a maximum cruising speed of 180 km/h. Design procedure for cross section design is established and design requirements for prop-blade are identified. Through the procedure, cross section design is carried out to meet the identified requirements. Main design factors including stiffness, weight per unit length, and elastic axis are obtained by using a finite element section analysis program, and the design weight of the prop-blade is predicted. The obtained design factors are used along with the rotor system analysis program CAMRAD II to evaluate the dynamic stability of prop-blade in operating environment. In addition, the prop-blade load is obtained by CAMRAD II software, and it is used to verify the safety of the prop-blade structure. If the design results are not satisfactory, design changes are made in an iterative manner until the results satisfy the design requirements.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.3 no.3 s.10
• /
• pp.125-132
• /
• 2003

In this study, safety analysis of river in flash flood due to local extraordinary rainfall was conducted for the Hong-Je river, which was selected as a representative sample basin because it is one of the most urbanized rivers in Seoul. The rainfall data of precipitation 310.1 mm and probable maximum precipitation (PMP) 740.0 mm in July $14{\sim}15$, 2001 was used to perform safety analysis. Resulting of safety analysis of the flood control in Hong-Je river, case of the 50 year of design frequency, safety section, management section, and danger section were represented to be 85%, 15%, and 0% respectively. For the 200 year of design frequency, safety section decreased by 6% and management section and danger section increment by 4% and 2%, respectively, The variation of management section was not observed with respect to 200 year of frequency. Little variation of safety value for management section for 300 and 500 of frequency increased by 8% and 12% relative to 50 year of frequency, respectively. management section and danger section for 1000 year of frequency increased by 19% and 13% relative to 50 year of frequency.

• Journal of Korea Water Resources Association
• /
• v.43 no.11
• /
• pp.945-956
• /
• 2010

Practically, the composite roughness coefficient, which is the equivalent roughness coefficient of a cross-section where the wall roughness is not constant along the wetted perimeter, is used to describe the flow conditions in open channels. In this study, it was conducted that the previous formulae was classified according to a weighting factor of the local resistance. The new subsection division method was also developed based on the force-balance concept in each subsection. The accuracy of the proposed method was examined and the applicability and limitation of the 13 existing formulae were analyzed by comparing the calculated with the experimental measured data from Djajadi (2009) and Knight and Macdonald (1979). It was found that Horton's method might underestimate the total conveyance of a composite channel and Lotter's method showed a good agreement between calculated and measured data. However, the proper division method, such as the proposed method based on the Z-method, is required for the application of Lotter's method.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.617-620
• /
• 2008

When the RC structure repaired by patching repair method, which method refilles with patching repair material after removes degraded area, It is necessary to determine chloride ion's permeation from outside of the RC structure repaired by patching repair material. Therefore, in this study, damage from sea environment of structure was predicted, moreover, diffusion coefficient of concrete also determined to figure out rebar's corrosion and concentration of chloride ion. RCPT(Rapid Chloride Permeability Test) was used for ditermination of patching repair material's diffusion coefficient, also connection between material thickness and effect of chloride ion's permeation was examined in analytically. Results which derived by experimental test was used in FEM(Finite Element Method) and equation suggested by JSCE to predict concentration of chloride ion in different distance from surface.

• Journal of Aerospace System Engineering
• /
• v.13 no.2
• /
• pp.51-59
• /
• 2019

Subsequently, Part I [1], which was about the single-cell model, a composite thin-walled beam with a multi-cell of chord-wise asymmetric cross-section, was selected in this study. Moreover, the theoretical dynamic characteristics of the model were analyzed. For this analysis, mathematical modeling was performed by considering the warping restraint effects, transverse shear effects, taper ratio and cross-section ratio. Similar to part I, the mass, stiffness coefficients and Eigen frequencies of the multi-cell section considered were investigated. In particular, the comparison between the multi-cell and single-cell sections and the effects of the cross-section ratio and taper ratio of the model on the Eigen frequencies were analyzed. However, the results compared when the asymmetry of the section was considered and warping function were not corrected.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.1
• /
• pp.37-49
• /
• 2012

A structural model of the SNF(spent nuclear fuel) disposal canister for the PWR(pressurized water reactor) for about 10,000 years long term deposition at a 500m deep granitic bedrock repository has been developed through various structural safety evaluations. The SNF disposal baskets of this canister model have the array type whose four square cross section baskets stand parallel to each other and symmetrically with respect to the center of the canister section. However, whether this developed structural model of the SNF disposal canister is optimal is not determinable yet. Especially, there is still a problem in weight-reduction of the canister. The cross section shape of the SNF basket should be changed to solve this problem. There are two ways in changing the cross section shape of the SNF basket; the one is to rotate the cross section itself and the other is to change the cross section shape as other shape different from the square cross section. The previous study shows that the canister with $30{\sim}35^{\circ}$ rotated basket array is structurally more stable than the canister with un-rotated parallel basket array. However, whether this canister with rotated basket array is optimal is not either determinable as yet, because it is not revealed that the canister with other cross section different from the square cross section is structurally more stable than other canisters. Therefore, the structural analysis of the SNF disposal canister with other cross section shape which is also symmetric with respect to the canister center planes is very necessary. The structural analysis of the canister with various cross section shape basket array in which each basket is arrayed symmetrically with respect to the center planes is carried out in this paper. The structural analysis result shows that the SNF disposal canister with circular cross section shape baskets located symmetrically with respect to the center of the canister section is structurally more stable than the previously developed SNF disposal canister with the parallel basket array.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.1
• /
• pp.71-81
• /
• 1994

A method is presented for the analysis of curved segmentally erected prestressed concrete box girder bridges including time-dependent effects due to load history, temperature history, creep, shrinkage, aging of concrete and relaxation of prestressing steel. The segments can be either precast or cast-in-place. Thin-walled beam theory and finite element method are combined to develop a curved nonprismatic thin-walled box beam element. The element consists of three nodes and each node has eight displacement degrees of freedom, including transverse distortion and longitudinal warping of the cross section.

• Journal of the Society of Naval Architects of Korea
• /
• v.37 no.2
• /
• pp.14-21
• /
• 2000

The cavitation noise of 2-D hydrofoils is measured a cavitation tunnel. A new experimental method was developed for the noise measurement of 2-D hydrofoil. Three hydrofoils with the span of 600mm are designed and manufactured to investigate cavitation behavior and noise characteristics. The experimental results show the noise characteristics of various cavitation patterns and the noise performance of the three foils very well. This suggests that low-noise propeller blade section can be developed using the present experimental method.