• Proceedings of the SAREK Conference
• /
• 2007.06a
• /
• pp.6-6
• /
• 2007

• Proceeding of EDISON Challenge
• /
• 2013.04a
• /
• pp.343-348
• /
• 2013

초임계 익형은 천음속 영역에서 비행하는 상업용 민간 항공기와 전투기 날개의 공력성능을 향상시키기 위해 Whitcomb R. T.가 제안 하였다. 초임계 익형은 상부표면을 평평하게 디자인하여 임계마하수보다 큰 마하수에서 나타나는 익형 주위의 충격파 출현을 지연시킴으로써 항력을 줄일 수 있고, 상부 표면의 평면 설계로 인한 양력 감소를 보정하기 위하여 하부 표면의 꼬리부분에 캠버가 있는 형상을 하고 있다. 본 연구에서는 EDISON CFD를 이용하여, 초임계 익형의 공력특성을 해석하고 Xfoil의 data와 비교 분석하였다. 또한, 초임계 익형의 형상을 변경하여 두께와 뒷전 캠버가 다른 초임계 익형을 설계하였다. 새로운 초임계 익형의 형상은 상용 프로그램 Maple12을 이용하여 Whitcomb Integral Supercritical Airfoil의 형상을 수정하여 구할 수 있다. 초임계 익형 주위의 유동을 2D압축성 유동으로 가정하고 EDISON CFD의 2D_Comp-2.0 솔버를 사용하여 수치해석을 수행하였다.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.554-559
• /
• 2016

본 논문은 EDISON CFD를 사용하여 스포일러가 장착된 무미익 BWB UCAV에 대하여 이차원 유동해석을 수행하였다. 무미익 형상은 일반적인 항공기보다 롤과 요 방향의 안정성과 조성성에 있어 불리한 특징을 갖는데 특히 이 착륙 시 고 받음각의 영역에서 발생하는 Pitch-up 현상이 항공기 안정성에 문제를 야기한다. 수직 미익 부재와 pitch-up 현상으로 인한 BWB형상의 UCAV가 지니는 단점을 보완하기 위해서 스포일러가 장착된 형상이 적용되기도 한다 본 연구에서는 윗면과 아랫면에 스포일러가 장착된 경우에 대해 전산유동해석을 수행하였다. 해석결과 윗면의 스포일러는 양력의 감소와 항력의 증가를 야기했으며, 아랫면의 스포일러는 양력과 항력을 모두 증가시켰다. 피칭모멘트의 경우 아랫면의 스포일러가 저받음각에서 안정성을 증가시켰다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.2
• /
• pp.165-170
• /
• 2007

During the conceptual design phase of a wing-body-canard type fighter class aircraft, as a method of maneuverability enhancement for an aircraft, effects of canard-leading edge flap scheduling have been studied. In this study, corrected supersonic panel method has been used to predict the drag polar characteristics due to canard-leading edge flap deflections in the high speed regime. Utilizing the predicted drag polar curves, the canard-leading edge flap scheduling laws have been established. These scheduling laws are the relation of canard-leading edge flap deflections and the flight conditions to maximize the lift-drag ratio. Based on the results obtained from the canard-leading edge flap scheduling, the present method has shown to be useful to enhance the maneuverability of wing-body-canard type fighter class aircraft.

• Journal of Advanced Navigation Technology
• /
• v.14 no.5
• /
• pp.697-709
• /
• 2010

The patrol robot is a typical extreme robot for the military use. It helps soldiers by detecting and informing a potential risk instead, and warning earlier. Also, these kinds of extreme robots need good ability to conquest rough road. In this paper, we studied new mechanism through which we can get high speed on the flat road with round shape wheels, and simultaneously can get good ability to overcome rough road with blade-shape wheels. The shape of the wheels is being self-adaptively changed automatically according to the condition of the road without using additional actuator.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.6
• /
• pp.530-536
• /
• 2010

In-flight icing is a critical technical issue for aircraft safety and, in particular, ice accretions on aircraft surfaces can drastically impair aerodynamic performances and control authority. In order to investigate icing effects on the aerodynamic characteristics of KC-100 aircraft, a state-of-the-art CFD code, FENSAP-ICE, was used. A main wing section and full configuration of KC-100 aircraft were considered for the icing analysis. Also, shapes of iced area were calculated for the design of anti-/de-icing devices. The iced areas around leading edge of main wing and horizontal tail wing were observed maximum 7.07% and 11.2% of the chord length of wing section, respectively. In case of wind shield, 16.7% of its area turned out to be covered by ice. The lift of KC-100 aircraft were decreased to 64.3%, while the drag was increased to 55.2%.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.1
• /
• pp.10-17
• /
• 2018

The size of commercial wind turbines has been increased. Generally, the pitch control is used to increase the efficiency of wind turbine. However, the pitch control has difficulty to control the local unsteady flow control which makes fatigue load and decreases the efficiency. In this research, Synthetic Jet Actuators(SJAs) are manufactured and applied into a wing section to delay flow separation and increase aerodynamic performances. The SJAs as a kind of zero-net mass-flux actuators injects and removes fluid through a small orifice with a given frequency. The SJA modules actuated by piezoelectric disks are manufactured and the aerodynamic performances are measured according to the shape of the orifice and the velocity of the jets through the wind tunnel test. It is confirmed that as the velocity of the jets are increased using rectangular shape orifice, drag force is decreased and lift force in increased.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.2
• /
• pp.200-206
• /
• 2015

In order to verify the lift enhancement of the 2D hydrofoil with trailing edge rotor and check the ability of its practical use, experimental studies were conducted in the caviation tunnel using the test model with NACA0020 section. The three-component forces acting on the model could be measured by exclusively designed sting type multi-component load cell. The trailing edge of the model has been replaced with rotor which could be controlled by DC servo motor installed at the exterior of the tunnel. A typical effect of the trailing edge rotor has been introduced among the systematic experiments on various angular deviation of the model and the rotational velocity of the trailing edge rotor. It is appeared that the circulation control effect could be easily adjusted by selecting the rotational velocity of the trailing edge rotor and the lift force was augmented more than two times. Thus the proposed lifting device could be utilized as a novel high lifting device which has adjustability of lift force.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.303-307
• /
• 2009

Secondary flow losses can be as high as $30{\sim}50%$ of the total aerodynamic losses generated in the cascade of a turbine. Therefore, these are important part for improving a turbine efficiency. As well, many studies have been performed to decrease the secondary flow losses. The present study deals with the leading edge fences on a wing-body to decrease a horseshoe vortex, one of the factors to generate the secondary flow losses, and optimizes the shape of leading-edge fence with the shape factors, such as the installed height, length, width, and thickness of the fence as the design variables. The study was investigated using $FLUENT^{TM}$ and $iSIGHT^{TM}$. Total pressure loss coefficient was improved about 7.5 % than the baseline case.

• Aerospace Engineering and Technology
• /
• v.11 no.2
• /
• pp.65-72
• /
• 2012

Numerical simulations were performed to study the stall characteristics of turboprop aircraft. Stall characteristics were qualitatively investigated using the computational results of various configurations based on the combinations of propeller and high lift device. For the analysis of stall characteristics, three-dimensional Navier-Stokes solver with Spalart-Allmaras turbulence model was used and the relative motion between propeller and wing was simulated using sliding mesh technique. For the cruise configurations, major flow separation was occurred at the fuselage/wing fairing and the separation was reduced under propeller slipstream condition. For the high lift device configuration without propeller, major flow separation was occurred at the outboard side of nacelle. With rotating propeller, early stall onset due to low relative velocity and high effective angle of attack was observed on the outboard wing section. Regarding rotating direction of propeller, inboard-down direction was preferred due to the stall delay effect of propeller slipstream.