• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.262-262
• /
• 2009

최근 리튬이차전지가 전지자동차, hybrid car, PHEV, Ev, UPS 저장장치로 사용되기 시작함에 따라 고용량화, 고출력화가 요구되고 있다. 현재까지 주로 사용 되어왔던 carbon으로는 작동전압이 낮고, 고용량화, 고출력화가 어려워 금속산화물, 금속 비정질 금속 및 금속산화물을 carbon과 혼합 사용 함으로써 차세대 전지로서 특성을 달성하고 있다. 따라서 본 연구에서는 음극 소재로서 안정성이 뛰어난 금속산화물로 $Li_4Ti_5O_{12}$를 합성할 때 저가의 $TiCl_4$를 이용 $Li_4Ti_5O_{12}$가 고밀도를 갖게끔 $TiCl_4$를 이용 구형의 Ti-precursor(전구체)를 합성한 후 구형의 $Li_4Ti_5O_{12}$를 합성하였다. Ti전구체는 $TiCl_4$로부터 합성하였는데 이때 구형을 제조하고자 Hydroxypropyl cellulose(이하 HPC)를 사용하여 반응을 진행하였다. 이때 반응 조건 및 HPC의 몰수 변화에 따른 입자 형상의 변화에 관하여 관찰한 결과, $TiOCl_2$ 0.4mol, 반응온도 $10^{\circ}C$, 유지시간 6시간, HPC양 0.02mol일 때 $0.6{\mu}m$ 정도의 구형 Ti-전구체를 합성하였다. 합성된 Ti-전구체와 리튬수화물을 사용하여 $Li_4Ti_5O_{12}$를 합성 하였고, 상기 물질로 전지특성을 평가하였다.

• Journal of the Korean Electrochemical Society
• /
• v.25 no.1
• /
• pp.1-12
• /
• 2022

Lithium metal is the most promising anode for next-generation lithium-ion batteries due to its lowest reduction potential (-3.04 V vs. SHE) and high specific capacity (3860 mAh/g). However, the dendritic formation under high charging current density remains one of main technical barriers to be used for commercial rechargeable batteries. To address these issues, tremendous research to suppress lithium dendrite formation have been conducted through new electrolyte formulation, robust protection layer, shape-controlled lithium metal, separator modification, etc. However, Li/Li symmetric cell test is always a starting or essential step to demonstrate better lithium dendrite formation behavior with lower overpotential and longer cycle life without careful analysis. Thus, this review summarizes overpotential behaviors of Li/Li symmetric cells along with theoretical explanations like initial peaking or later arcing. Also, we categorize various overpotential data depending on research approaches and discuss them based on peaking and arcing behaviors. Thus, this review will be very helpful for researchers in lithium metal to analyze their overpotential behaviors.

• Proceedings of the KAIS Fall Conference
• /
• 2007.11a
• /
• pp.353-355
• /
• 2007

본 논문에서는 리튬금속을 음극으로 하는 반전지에 여러 농도의 전해질을 사용하여 그에 따른 충/방전 효율과, 음극 표면을 관찰하는 것에 의해 전해질 농도가 음극/전해질 계면반응에 어떠한 영향을 끼치는지 알아보았다. 또한 X-ray Photoelectron Spectroscopy(XPS)를 사용하여 표면에 생성되는 물질의 조성과 구조를 해석하였다.

• Analytical Science and Technology
• /
• v.5 no.1
• /
• pp.33-39
• /
• 1992

THF-based crown-4 of 16-membered rings having tetrahydrofuran unit was synthesized by an acid-catalyzed condensation of furan and acetone followed by hydrogenation in an effort to obtain highly elective ionophores for lithium ions. The new ionophore was compared with previously reported ionophores under similar measurement conditions with the same plasticizer, tris(2-ethylhexyl) phosphate in poly(vinyl chloride)(PVC) membrane electrodes. Separate solution method was used to determine relative selectivity coefficients for the electrode. The selectivity coefficients($K_{LiM}^{POT}$) of lithium over ammonium, alkali and alkaline earth metal ions go from about $2.4{\times}10^{-1}$ to $2.3{\times}10^{-4}$ to working range and pH dependence have also been studied.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.192.2-192.2
• /
• 2016

최근 차세대 휴대용 전자기기나 전기자동차의 상용화 연구가 활발히 이루어짐에 따라 리튬이온 배터리가 주력 에너지 저장장치로써 활발히 개발되고 있다. 이러한 리튬이온 배터리의 음극 물질로써 주로 탄소재료가 많이 사용되어 왔지만 낮은 이론용량 (372 mAh/g)으로 인하여 좀더 높은 용량을 가지는 금속이나 합금 등이 주목을 받게 되었다. 그 중에서도 주석이 탄소재료에 비해 3배 정도 높은 이론 용량 (993 mAh/g)을 가지고 있어 많은 연구가 진행되고 있다. 하지만 주석의 경우 리튬이온 배터리의 충방전 과정 중에 급격한 부피 변화가 발생하여 음극이 손상되고 이에 따라 용량이 급격하게 감소하는 한계점이 있다. 이 한계를 극복하기 위한 많은 방법들 중 하나가 구리-주석 합금을 음극으로 사용하는 것이다. 구리는 비활성 금속으로 충방전 중의 부피 변화에 완충제 역할을 하고, 연성과 전기전도성이 있어서 배터리의 전기화학적 성능 또한 향상시켜 준다. 이에 따라, 본 연구에서는 주석이 풍부한 구리-주석 합금 도금을 통하여 구조적으로 튼튼한 리튬이온 배터리의 음극을 만들었고 그 성능을 확인하기 위하여 반쪽전지 실험을 통하여 500회 충방전 동안의 싸이클 특성 및 효율을 확인하였고 순환전압전류 실험 또한 진행하였다.

• Membrane Journal
• /
• v.34 no.3
• /
• pp.163-171
• /
• 2024

Growing demand on clean energy to control environmental pollution is growing rapidly. Rechargeable battery such as lithium ion battery is excellent source of clean energy but there is rapid depletion of lithium metal due to high demand and supply mismatch. Recovery of the precious metal from the battery waste is one of the possible solution along with the environmental pollution control. Membrane based separation method is highly successful commercial process available to recover lithium from the waste. This work will cover various methods reported recently and will be compiled in the form of a review.

• Membrane Journal
• /
• v.26 no.4
• /
• pp.310-317
• /
• 2016

Lithium ion secondary battery (LISB) is an energy conversion system operated via charging-discharging cycle based on Lithium ion migration. LISB has a lot of advantages such as high energy density, low self-discharge rate, and a relatively high lifetime. Recently, increasing demands of electric vehicles have been encouraging the development of LISB with high capacity. Unfortunately, it causes some critical safety issues. It includes dendrite formation on negative electrode, resulting in electric shortage problems and battery explosion. Also, the elevated temperatures occurred during the LISB operation induces thermal shrinkage of polyolefin (e.g., polyethylene and polypropylene) separators. Consequently, the low thermal stability leads to decay of LISB performances and the reduction of lifetime. In this study, sulfonated poly (arylene ether sulfone) (SPAES) random copolymers were used as key materials to prepare polyolefin pore-filling separator. The resulting separators were evaluated in the term of metal ion chelation capability associated with dendrite formation, $Li^+$ ion conductivity and thermal durability.

• Membrane Journal
• /
• v.30 no.1
• /
• pp.38-45
• /
• 2020

Although Lithium metal battery (LMB) has a very large theoretical capacity, it has a critical problem such as formation of dendrite which causes short circuit and short cycle life of the LMB. In this study, PDMS/GO composite with evenly dispersed graphene oxide (GO) nanosheets in poly (dimethylsiloxane) (PDMS) was synthesized and coated into a thin film, resulting in the effect that can physically suppress the formation of dendrite. However, PDMS has low ion conductivity, so that we attained improved ion conductivity of PDMS/GO thin film by etching technic using 5wt% hydrofluoric acid (HF), to facilitate the movement of lithium (Li) ions by forming the channel of Li ions. The morphology of the PDMS/GO thin film was observed to confirm using SEM. When the PDMS/GO thin film was utilized to lithium metal battery system, the columbic efficiency was maintained at 87.4% on average until the 100^th cycles. In addition, voltage profiles indicated reduced overpotential in comparison to the electrode without thin film.

• Resources Recycling
• /
• v.29 no.5
• /
• pp.73-80
• /
• 2020

In order to develop a process for the recovery of valuable metals from spent LiBs, solvent extraction experiments were performed to separate Cu(II) and/or Co(II) from synthetic hydrochloric acid solutions containing Li(I), Mn(II), and Ni(II). Commercial amines (Alamine 336 and Aliquat 336) were employed and the extraction behavior of the metals was investigated as a function of the concentration of HCl and extractants. The results indicate that HCl concentration affected remarkably the extraction efficiency of the metals. Only Cu(II) was selectively at 1 M HCl concentration, while both Co(II) and Cu(II) was extracted by the amines when HCl concentration was higher than 5 M, leaving the other metal ions in the raffinate. Therefore, it was possible to selectively extract either Cu(II) or Co(II)/Cu(II) by adjusting the HCl concentration.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05a
• /
• pp.158-160
• /
• 2011

본 연구에서는 리튬 금속을 음극소재로 사용하기 위해 수지상 리튬의 성장을 억제하기 위한 지침을 얻기 위한 목적으로 TEM(Transmission Electron Microscope)과 임피던스를 주된 분석 수단으로 이용하여 2. 15 M LiBETI/ PC, 2.04 M $LiClO_4$/ PC 전해질은 1 M LiBETI/ PC, 1 M $LiClO_4$/ PC 전해질보다 얇고 치밀한 SEI(Solid Electrolyte Interphase) 구조를 가지고, 클로로포름에 의해 SEI의 유기물이 녹아 두께가 얇아 졌다. 임피던스를 측정한 결과 두꺼운 두께를 가진 SEI는 저항이 더 크고, 클로로포름 처리 후에는 저항이 커진 것을 확인할 수 있었다.