• Fire Science and Engineering
• /
• v.24 no.5
• /
• pp.50-59
• /
• 2010

Four fire scenarios, as the cases of fire sizes of 2 MW and 5 MW, and no installation and activation of atrium fire shutter for dormitory building of Daegu 'D college', were developed and fire simulations were run using FDS (ver. 5.5.0) and Pathfinder 2009 programs. By assessing fire and evacuation, the effects of atrium fire shutter and vents on the smoke control of atrium were evaluated and this study also analyzed fire hazard and egress safety for occupants in the dormitory. Fire shutter's preventing smoke transport around atrium was much effective, but smoke layer descended down the design limit of smoke height and kept about 2 m height from the atrium floor in all cases because flow rate through vents was not enough. For the case of 5 MW fire and no fire shutter, fire hazard was higher due to visibility than temperature and allowable egress time to stairwell was short less than 5 seconds for the occupants on the floors of 4F to 7F. For total occupants, egress time out of main doorway was calculated about 136 seconds. It is sure that additional systems improving the performance of smoke control need to be installed for more safe evacuation.

• Fire Science and Engineering
• /
• v.34 no.1
• /
• pp.135-141
• /
• 2020

The first case of Middle East Respiratory Syndrome (MERS) was reported in Korea in 2015, after a Korean man from Bahrain tested positive for the infection. After first eruption, there were numbers of secondary infectees and whole country were frightened. At the time, isolated ambulances were available but few, and there was no specific way to prevent contamination during transfer. Therefore, Seoul National University Hospital and the University of Seoul developed isolation units and air filters. Four years after the MERS outbreak, this study measured the differential pressure inside and outside the small isolation units based on the differential pressure and air flow derived from simulation and testing, and proposed minimum values for virus leakage and internal sealing. A performance evaluation and testing method for the transfer equipment is proposed. The critical function of the small isolated transport equipment was defined and selected as an evaluation item; performance evaluation was carried out by simulating a real-world case. The results provide the proper pressure configuration of positive and negative pressure inside the segregation feeder; the clear criteria for the HEPA filter; and the performance criteria for the segregation feeder and air purifier.

• The Journal of Society for e-Business Studies
• /
• v.15 no.3
• /
• pp.163-181
• /
• 2010

As a part of efforts to reduce the global emissions of greenhouse gases, the Kyoto Protocol was signed by major developed countries ("Annex I" countries). According to the Kyoto protocol, the Emission Trading Scheme that derives a trading market of the $CO_2$ emission rights is appeared. It causes that business institutions give lots of efforts to reduce $CO_2$ by using new environmentally sound technologies or increasing efficiency in production. On the while there have been several studies trying to develop a methodology to measure the effect of $CO_2$ reduction and its monetary value. In this research we suggest ECRE (Evaluation of $CO_2$ Reduction in E-transformation) model which can measure the $CO_2$ reduction effect through the introduction of G2B system. ECRC model was developed based on the IPCC methodology. ECRC model measures the two major effects of the $CO_2$ reduction which are '$CO_2$ reduction effect from transportation' and '$CO_2$ reduction effect from the decrease of paper use'. In this paper, we calculate the economic effect of $CO_2$ reduction with the case of the G2B system in Korea. This research suggests a basic methodology to measure the $CO_2$ reduction performance for the e-transformed institution.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.12
• /
• pp.80-87
• /
• 2013

A novel instrumentation amplifier(IA) using positive polarity current-conveyor(CCII+) for electronic measurement systems with low cost, wideband, and gain control with wide range is designed. The IA consists of two CCII+, three resistor, and an operational amplifier(op-amp). The principal of the operating is that the difference of two input voltages applied into two CCII+ used voltage and current follower converts into same currents, and then these current drive resistor of (+) terminal and feedback resistor of op-amp to obtain output voltage. To verify operating principal of the IA, we designed the CCII+ and used commercial op-amp LF356. Simulation results show that voltage follower used CCII+ has offset voltage of 0.21mV at linear range of ${\pm}$4V. The IA had wide gain range from -20dB to 60dB by variation of only one resistor and -3dB frequency for the gain of 60dB was 400kHz. The IA also has merits without matching of external resistor and controllable offset voltage using the other resistor. The power dissipation of the IA is 130mW at supply voltage of ${\pm}$5V.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.2
• /
• pp.185-195
• /
• 2018

As machines have been automated in the field of industries in recent years, it is a paramount importance to manage and maintain the automation machines. When a fault occurs in sensors attached to the machine, the machine may malfunction and further, a huge damage will be caused in the process line. To prevent the situation, the fault of sensors should be monitored, diagnosed and classified in a proper way. In the paper, we propose a sensor fault detection scheme based on SVM and CNN to detect and classify typical sensor errors such as erratic, drift, hard-over, spike, and stuck faults. Time-domain statistical features are utilized for the learning and testing in the proposed scheme, and the genetic algorithm is utilized to select the subset of optimal features. To classify multiple sensor faults, a multi-layer SVM is utilized, and ensemble technique is used for CNN. As a result, the SVM that utilizes a subset of features selected by the genetic algorithm provides better performance than the SVM that utilizes all the features. However, the performance of CNN is superior to that of the SVM.

• The Journal of Korean Association of Computer Education
• /
• v.8 no.4
• /
• pp.79-86
• /
• 2005

Educational objectives are the most important items because not only they must be decided first in the circulation process of curriculum but also they should be the basis for the process of curriculum. The establishment of objectives is very important because it can determine success or failure of computer education. In this paper, questionnaire research is conducted and analyzed for male students of middle schools in Chungbuk province, Korea to determine that it's reasonable for computer games to be perceived negatively. The results of the research are as follows. 48% of them are represented to play computer game almost everyday, and 8% to play it scarcely. So most of students are enjoying it regardless of their grade. If students whose grades are ranked upper level start playing games, they're tend to quit it within 1 or 2 hours. And they enjoy role-playing or simulation game. In general, they do not play action games. If their grades are ranked lower level start playing games, a lot of them continue to play longer than 3 hours like game addict. And in this level, there exist students who barely play games. In middle level, there are no apparent characteristics. According to the result of the research, there is no correlation between frequency of playing games and academic achievements. So it's no problem to relieve worries if one often play computer games, his or her grade will get down. In case that the grades of students are ranked upper level, however, there are few who continue to play games longer than 3 hours.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.6
• /
• pp.85-96
• /
• 2000

It is necessary that fully differential operational amplifier circuit should drive an external load in the VLSI design such as SCF(Switched Capacitor Filter), D/A Converter, A/D Converter, Telecommunication Circuit and etc. The conventional CMOS operational amplifier circuit has many problems according to CMOS technique. Firstly, Capacity of large loads are not able to operate well. The problem can be solve to use class AB stages. But large loads are operate a difficult, because an element of existing CMOS has a quadratic functional relation with input and output voltage versus output current. Secondly, Whole circuit of dynamic range decrease, because a range of input and output voltages go down according as increasing of intergration rate drop supply voltage. The problem can be improved by employing fully differential operational amplifier using differential output stage with wide output swing. In this paper, we proposed new current mirror has large output impedance and good current matching with input an output current and compared with characteristics for operational amplifier using cascoded current mirror. To obtain large output swing and low power consumption we suggest a fully differential operational amplifier. The circuit employs an output stage composed new current mirror and two amplifier stage. The proposed circuit is layout and circuit of capability is inspected through simulation program(SPICE3f).

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.2
• /
• pp.78-85
• /
• 1998

The design method of a temperature stable bandpass filter using dielectric coaxial resonators of with two dielectric ceramics with opposite signs of temperature coefficient of dielectric constant (${\tau}_{\epsilon}$) to compensate for each other in this method. $MgTiO_3$(${\tau}_{\epsilon}$=+99 ppm/${\circ}C$) as a positive ${\tau}_{\epsilon}$ material and Ba($Zn_{1/3}Nb_{2/3}$)$O_3$(${\tau}_{\epsilon}$=-77ppm/${\circ}C$) as a negative material were selected. The length of a SIR for the temperature stability was calculated according to the design method and the susceptance slope parameter of the SIR was obtained. A temperature stable bandpass filter using dielectric SIR's was designed, simulated and fabricated. The center frequency of this filter was 915 MHz and the pass bandwidth was 20 MHz. Temperature properties of this bandpass filter by simulations were compared with the measured results of the bandpass filter fabricated.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.6 s.324
• /
• pp.49-58
• /
• 2004

The existing route re-establishment methods which intend to extend the lifetime of the network attempt to find a new route in order not to overly consume energy of certain nodes. These methods outperforms other routing algorithms in the network lifetime aspect because that they try to consume energy evenly for the entire network. However, these algorithms involve heavy signaling overheads because they find new routes based on flooding method and route re-establishment occurs often. Because of the overhead they often can not achieve the level of performance they intend to. In this paper, we propose a new route selection algorithm which takes into account costs for the packet transmission and the route re-establishment. Since the proposed algerian considers future route re-establishment costs when it first find the route, it spends less energy to transmit given amount of data while evenly consuming energy as much as possible. Simulation results show that the proposed algorithm outperforms the existing route re-establishment methods in that after simulation it has the largest network energy which is the total summation of remaining energy of each node, the smallest energy consumed for route re-establishment, and the smallest energy needed for maintaining a session.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.4
• /
• pp.69-74
• /
• 2010

A new package substrate for dynamic random access memory(DRAM) devices has been developed using selective aluminum anodization. Unlike the conventional substrate structure commonly made by laminating epoxy-based core and copper clad, this substrate consists of bottom aluminum, middle anodic aluminum oxide and top copper. Anodization process on the aluminum substrate provides thick aluminum oxide used as a dielectric layer in the package substrate. Placing copper traces on the anodic aluminum oxide layer, the resulting two-layer metal structure is completed in the package substrate. Selective anodization process makes it possible to construct a fully filled via structure. Also, putting vias directly in the bonding pads and the ball pads in the substrate design, via in pad structure is applied in this work. These arrangement of via in pad and two-layer metal structure make routing easier and thus provide more design flexibility. In a substrate design, all signal lines are routed based on the transmission line scheme of finite-width coplanar waveguide or microstrip with a characteristic impedance of about $50{\Omega}$ for better signal transmission. The property and performance of anodic alumina based package substrate such as layer structure, design method, fabrication process and measurement characteristics are investigated in detail.