• Journal of Aerospace System Engineering
• /
• v.14 no.1
• /
• pp.1-7
• /
• 2020

This paper discusses a series of procedures and results for designing the gear part of a fuel transfer pump for an aircraft, developed as an independent technology for the first time in Korea. A gear pump type is selected because the design requirements of the fuel transfer pump are met by a gear pump with a characteristics of less leakage inside than a vane pump with superior overall performance. The gear housing is designed with suitable clearance, considering the outer diameter of the gear, which is the main factor on which the flow can be determined. Additionally, the calculation of the required hydraulic and axial force for the motor to drive the fuel transfer pump was performed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.6
• /
• pp.512-519
• /
• 2016

Auxiliary Power Unit of FA-50 which provides energy other than propulsion is an important element to maintain airworthiness on aircraft. Also Inlet Guide Vane of Auxiliary Power Unit is a device that supplies appropriate airflow into the Auxiliary Power Unit after adjusting influent airflow into the load compressor. This report, based on the problems occurred the driving gears of Inlet Guide Vane, deals with cause of occurrence, troubleshooting, design improvement and result of test flight verification for FA-50 aircraft Auxiliary Power Unit lifespan.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.2
• /
• pp.259-266
• /
• 2020

Magnetic gears have the same characteristics as mechanical gears, and each rotor does not come in contact, which is advantageous over mechanical gears in friction noise, heat generation, and maintenance. In addition, when the rotor using the coil-winding is applied, it is possible to control the output of the gear as well as to cut off its own drive in the emergency situation and to change its gear ratio. So the application of the magnetic gear is infinite. However, when the coil-winding rotor is used, cogging torque due to the attraction force between the permanent magnet and the iron core appears, which leads to an increase in the torque ripple component causing the rotor vibration. Therefore, in this paper, various shapes of the coil-winding rotor are analyzed to reduce the torque ripple of the rotor, and the optimum shape for reducing the torque ripple of the magnetic gear is presented.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.4
• /
• pp.147-153
• /
• 2000

This paper presents a design method using CAE(Computer Aided Engineering ) with the consideration of reliability for optimal gear driving system. This method considered a configuration of the intermediate shaft. There are four mounting types, such as double straddle, double overhung, output gear overhung, and input ger overhung in the intermediate shaft. The reliability and life analysis are based on the two-parameter Weigbull distribution lives of the gears and bearing . The validity and feasibility of the proposed method are verified by the application to transmission of a industry machine.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.25-30
• /
• 2002

To reduce the vibration of a gear driving system, the modification of gear tooth from the orignal involute gear profile is usually done in gear manufacturers. The quantity of tooth modification has been decided on the basis of the interference between two gear teeth during gear meshing and the elastic deformation due to loading. However, the dynamic characteristics with tooth modification has to be investigated to avoid the instability to the variation of gear meshing stiffness and the nonlinearity due to gear backlash which results in sub- or super-harmonics in its responses. This research shows the dynamic characteristics with various tooth modifications in its type and quantity.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.31-36
• /
• 2002

Even through the problem of misalignment is of great importance, not much work has been reported in the literature on the effect of misalignment on the vibrations of the gear-bearing systems. Therefore, the nonlinear dynamic characteristics of the gear drive system due to misalignment are investigated in this work. Transmission error for helical gear and bearing nonlinear stiffness is calculated. The equation of motion of the gear drive system is modelled using the time-varying gear meshing stiffness, bearing nonlinear stiffness, and bearing pre-load due to the housing deformation. Numerical analysis lot the gear drive system show the result of misalignment effect - sub-harmonic component, bearing pre-load effect, and another nonlinear phenomenon. And the numerical analysis are verified by the experimental result.

• JOURNAL OF ELECTRICAL WORLD
• /
• s.305
• /
• pp.69-74
• /
• 2002

최근 승강기의 현대화 사업에서는 단공기(短工期)$\cdot$저가격으로 특히 신뢰성 향상을 기대할 수 있는 제어개수(制御改修:전기기기를 일신하는 개수방법)가 주류를 이루고 있다. 그래서 미쓰비시(삼릉)전기에서는 납품한지 20년 이상 경과한 직류-기어리스(DC-GL)고속엘리베이터를 대상으로 하는 제어개수전용의 구동방식을 개발하여 동사 본사빌딩에 납품하였다. 새로운 구동방식은 현재 널리 적용되고 있는 고속엘리베이터의 인버터제어기술을 응용하여 개발한 초퍼회로방식이다. 제어회로에서는 동사의 최신 엘리베이터와 같은 마이컴시스템을 채용하여 고성능화와 부품의 공용화를 도모하였다. 또한 주회로에는 고조파대책, EMI(Eletro-magnetic Interference) 대책 및 누설전류대책을 시행하였다. 특히 직류전동기의 계자제어에서는 엘리베이터의 운전상태에 따라 계자전류를 가변하는 가변계자전류제어를 적용하였다. 이번에 개발한 제어방식은 다음의 특징을 갖고 있다. (1)고조파전류를 억제하였기 때문에 빌딩측에서의 고조파대책이 불필요하다. (2)동사 제작의 워드레오나드방식과 비교하여 약 $40\%$정도 소비전력을 감소시킬 수 있다. (3)동사 제품인 최신 엘리베이터 수준의 성능(승차감, 착상정도 등)을 실현하였다. (4)최신 엘리베이터와 동등한 풍부한 옵션에 대응할 수 있다. 당분간은 속도 $120\~$360m/min, 용량 1,600kg 이하의 고속엘리베이터에 적용하고 점차적으로 적용영역을 확대해 나갈 예정이다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1589-1592
• /
• 2003

Automatic grease lubricator of gear type was developed by mechanical design, analysis and test with products manufactured by rapid prototyping machine. The mechanism of gear driving was designed in similar to the watch mechanism and lubrication could be controlled by PCB circuit. The body of the lubricator was analyzed by stress analysis with different constructed angle. Digital mockup was analyzed and RP products were combined with PCB circuit and grease. RP products and injection moulding products were tested and compared for roughness and roundness, Finally the grease was drained out for testing the time.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1990.10a
• /
• pp.187-191
• /
• 1990

그동안 실험을 통해 측정된 울산화력 BFP 진동 Data의 분석을 통하여 문제 가 되는 과도진동원에 대한 분석이 시도되었다. BFP의 이력과 그간의 측정 자료를 근거로 진동원과 진동에너지의 전달 경로를 가정하였고 각각의 진동 원에 대한 타당성 검토를 위하여 신호처리가 수행되었으며 그 결과로부터 BFP 과도진동 현상에 의해 야기되는 F 베어링 92.5 Hz의 진동에너지는 Voith Coupling의 기어에서 발생되었던 것으로 밝혀졌다. 문제의 해결을 위 해 치차를 대체시켰으며 진동값은 치차가 교환되기 전의 193.$\mu$m이 40.$\mu$m 이하로 줄 수 있었고 따라서 BFP는 안전운행 조건을 만족시키는 동급(Fair Operation)에 들게 됨을 볼 수 있다. BFP로부터 분리된 구동축 Gear는 육안상 크게 균열은 없어 보였으나 특정방향으로 일부 마모가 있어 보였으며 이는 유체와의 회전시 Unbalance에 의한 마모결과로 보여진다. 현 재 6-2 BFP에서 사용되었던 구동측 부품인 기어, Impellar는 치차마모등 비 파괴 정밀조사와 함께 Wet Balancing등의 측정이 진행되고 있다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.9
• /
• pp.688-693
• /
• 2003

To reduce the vibration of a gear driving system. the modification of gear tooth from the orignal involute gear profile is usually done in gear manufacturers. The quantity of tooth modification has been decided on the basis of the interference between two gear teeth during gear meshing and the elastic deformation due to loading. However. the dynamic characteristics with tooth modification has to be investigated to avoid the instability to the variation of gear meshing stiffness and the nonlinearity due to gear backlash which results in sub- or super-harmonics in its responses. This research shows the dynamic characteristics with various tooth modifications in its type and quantity.