• Journal of Soil and Groundwater Environment
• /
• v.13 no.2
• /
• pp.1-11
• /
• 2008

Phenanthrene uptake by surfactant sorbed on activated carbon was investigated to recycle of surfactant in washed solution for contaminated soil. The partitioning of phenanthrene to the activated carbon coating with Triton X-100 as a surfactant was also evaluated by a mathematical model. Phenanthrene-contaminated soil (200 mg/kg) was washed in 10 g/L of surfactant solution. Washed phenanthrene in solution was separated by various particle loadings of granular activated carbon through a mode of selective adsorption. Removal of phenanthrene was 99.3%, and surfactant recovery was 88.9% by 2.5 g/L of granular activated carbon, respectively. Phenanthrene uptake by activated carbon was greater than that of phenanthrene calculated by a standard model for a system with one partitioning component. This is accounted for enhanced surface solubilization by hemi-micelles adsorbed onto granular activated carbon. The effectiveness factor is greater than 1 and molar ratio of solubilization to sorbed surfactant is higher than that of liquid surfactant. Results suggest that separation of contaminants and surfactants by activated carbon through washing process in soil is much effective than that of calculated in a theoretical model.

• The Korean Journal of Pesticide Science
• /
• v.15 no.4
• /
• pp.389-400
• /
• 2011

A high-performance liquid chromatographic (HPLC) method was developed to determine residues of phenothrin and silafluofen, known as synthetic pyrethroids, in agricultural commodities. Insecticide residues were extracted with acetone from representative samples of four crops which comprised rice, apple, pepper and cabbage. The extract was purified serially by liquid-liquid partition and Florisil column chromatography. For rice and pepper samples, acetonitrile/n-hexane partition was additionally adopted to remove nonpolar interferences. Reversed phase HPLC using an octadecylsilyl column was successfully applied to separate two phenothrin isomers and silafluofen from sample co-extractives. Intact parent compounds were sensitively detected by ultraviolet absorption at 226 nm. Recovery experiment at the quantitation limit validated that the proposed method could apparently determine phenothrin and silafluofen residues at 0.02 and 0.01 mg/kg, respectively. Mean recoveries of phenothrin and silafluofen from four crop samples fortified at three levels in triplicate were in the range of 82.4~109.8% and 83.7~109.8%, respectively. Relative standard deviations of the analytical method were all less than 10%, irrespective of crop types and spiking levels. A selected-ion monitoring (SIM) LC/mass spectrometry (MS) with electrospray ionization was provided to confirm the suspected residue of phenothrin, even though no sufficient ionization of silafluofen was obtained. Both phenothrin and silafluofen could be successfully confirmed by gas chromatography/MS SIM with electron impact at 70 eV. The proposed method is sensitive, repeatable and rapid enough to apply to officially routine inspection of agricultural products.

• Korean Journal of Optics and Photonics
• /
• v.24 no.4
• /
• pp.184-188
• /
• 2013

Two types of polymer-based optical splitters with $200{\mu}m$ large core are presented for optical multimode networks, such as smart home networks, intelligent automotive networks, etc. Optical splitters that have 1:1 symmetric and 9:1 asymmetric structure were fabricated by a ultra violet(UV)-imprint technology using a deep etched Si(silicon) master by the Bosch process. In this paper, we successfully fabricated the symmetric and asymmetric optical splitters with suitable optical network applications.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.3336-3344
• /
• 2014

The purpose of this study is small scale coagulation module is developed and demonstrated through a lab-scale test. Recent as a sewage treatment rate increases, have heightened the interest in the necessity on the nonpoint source and developing a small processing unit has been increased. Coagulation sedimentation module in this study is additional growth of floc through swirling in the outside zone, reduction of microstructure floc number and the internal settling zone through vertical/level flow complex sedimentation method after the coagulation process precipitation method as an effective high separation efficiency can be divided was also assessed. Coagulation sedimentation module can increase the load factor was 4.4 times compared to conventional clarifier base on the same volume and surface area through vertical/level flow. In this study, this process was selected formation and maintenance of swirling and uniform flow distribution in the internal settling zone as an important design factor, to derive its FLUENT was used to characteristics of the flow model. Through the simulation of swirling, influent velocity, dimensions of external basin, hopper depth of bottom cone was determined and through analysis of velocity distribution, flow distribution detailed specifications are derived like as diameter and number of effluent hole. Lab-scale($120{\ell}/hr$) test results, influent of 300~800 NTU to less than 10 NTU without polymer feeding was able to operate in the 20minutes retention time(surface loading rate $37.3m^3/m^2$-day), and through analysis FLUENT the possibility of using design parameters were derived.

• Journal of Technology Innovation
• /
• v.18 no.2
• /
• pp.91-120
• /
• 2010

This paper examines the effect of bargaining power over intermediate goods prices on innovation and economic growth using a Schumpeterian growth model. The notion of "intermediate goods prices" broadly indicates the reward to innovators including innovative SMEs as well as intermediate goods producers that are vertically integrated to big businesses. From this viewpoint, this paper sets up a Schumpeterian growth model that incorporates the market power between final goods producers and intermediate goods producers. The results show that the reduction of intermediate goods prices slows down long-run growth rates as it erodes the reward to innovations. Lower intermediate goods prices decrease marginal productivity of capital and real interest rates. However, the harmful effect of lower profits on innovations outweighs the beneficial effect of lower interest rates. Simulations using Korea's data for various cases show that in all cases the policies that raise the share of intermediate goods producers are as powerful as the R&D subsidy policies in raising growth rates. Therefore, fair trade policies that enable intermediate goods producers-especially SMEs to obtain more fruits of innovations will be helpful for long-run economic growth.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.1
• /
• pp.148-156
• /
• 2013

This paper suggests a multi-level and multi-output SMPS based on a shared digital logic controller through independently operating in each dedicated time periods. Although the shared architecture can be devised with small area and high efficiency, it has critical drawbacks that real-time control of each DPWM generators are impossible and its output voltage can be unstable. To solve these problems, a real-time current compensation scheme is proposed as a solution. A current consumption of the core block and entire block with four driver buffers was simulated about 4.9mA and 30mA at 10MHz switching frequency and 100MHz core operating frequency. Output voltage ripple was 11 mV at 3.3V output voltage. Over/undershoot voltage was 10mV/19.6mV at 3.3V output voltage. The noise performance was simulated at 800mA and 100KHz load regulation. Core circuit can be implemented small size in $700{\mu}m{\times}800{\mu}m$ area. For the verification of proposed circuit, the simulations were carried out with Dong-bu Hitek BCD $0.35{\mu}m$ technology.

• KSBB Journal
• /
• v.20 no.3
• /
• pp.238-243
• /
• 2005

Succinic acid has recently been drawing much interest as a raw material for biodegradable polymer. In this study acetic acid was removed by reactive extraction with various amines dissolved in various diluents. Distribution coefficients were determined as the kind of amines, diluents, and pHs of continuous phase. The extraction capacity increased with the polarity of diluent and the decrease of pH from the artificial binary solution. Based on the different extractability for succinic acid and acetic acid from the artificial binary solution, the removal of acetic acid from fermentation broth was investigated using various amines and diluents. In addition, the extractability and selectivity of CLA for succinic acid and acetic acid from fermentation broth were higher than that of straight solvent extraction.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.581-584
• /
• 2014

In this paper, a micro-scale photovoltaic(PV) energy harvesting system is proposed where an MPPT(Maximum Power Point Tracking) control is implemented using an energy distribution technique. Miniature PV cells output very low energy and low voltages, and thus, they cannot be used to directly power the MPPT controller. In the proposed system, a start-up circuit boosts an internal Vcp, and the boosted Vcp is used to operate the internal MPPT control block. When the Vcp reaches a predefined value, a detector circuit makes the start-up block turn off and provide a power converter with the energy from the PV cell. When the Vcp decreases such that the MPPT controller can not be operated, the energy transferred to the power converter is blocked and the start-up circuit is reactivated. In this way, the MPPT function is achieved by alternately operating the start-up circuit and the power converter using the energy distribution technique, and the harvested energy is transferred to a load through a PMU(Power Management Unit). The proposed circuit is designed in a 0.35um CMOS process and its functionality has been verified through extensive simulations. The designed chip area including pads is $1430um{\times}1110um$.

• Korean Journal of Construction Engineering and Management
• /
• v.24 no.3
• /
• pp.12-19
• /
• 2023

In the case of the construction industry, the relationship between process and cost should be appropriately distributed so that the finished product can be delivered at the minimum fee within the construction period. At that time, it should be considered the size of the bridge, the construction method, the environment and production capacity of the factory, and the transport distance. However, due to various reasons that occur during the construction period, problems such as construction delay, construction cost increase, and quality and reliability degradation occur. Therefore, a systematic and scientific construction technique and process management technology are needed to break away from the conventional method. The prefab(Pre-Fabrication) is a representative OSC (Off-Site Construction) method manufactured in a factory and constructed onsite. This study develops a resource and process plan optimization system for the process management of the Nodular girder, a prefab bridge girder. A simulation algorithm develops to automatically test various variables in the personnel equipment mobilization plan to derive the optimal value. And, the algorithm was applied to the Paju-Pocheon Expressway Construction (Section 3) Dohwa 4 Bridge under construction, and the results compare. Based on construction work standard product calculation, actual input manpower, equipment type, and quantity were applied to the Activity Card, and the amount of work by quantity counting, resource planning, and resource requirements was reflected. In the future, we plan to improve the accuracy of the program by applying forecasting techniques including various field data.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.11A
• /
• pp.929-935
• /
• 2003

An analog/digital mixed mode ASIC for network synchronization of ATM switching system has been designed and fabricated. This ASIC generates a 234.7/46.94 ㎒ system clock and 77.76/19.44 ㎒ user clock using 46.94 ㎒ transmitted clocks from other systems. It also includes digital circuits for checking and selecting of the transmitted clocks. For effective ASIC design, full custom technique is used in 2 analog PLL circuits design, and standard cell based technique is used in digital circuit design. Resistors and capacitors for analog circuits are specially designed which can be fabricated in general CMOS technology, so the chip can be implemented in 0.8$\mu\textrm{m}$ digital CMOS technology with no expensive. Testing results show stable 234.7 ㎒ and 19.44 ㎒ clocks generation with each 4㎰ and 17㎰ of low ms jitter.