• Fire Science and Engineering
• /
• v.29 no.4
• /
• pp.33-38
• /
• 2015

Loads applied on the floor are transferred through beams to columns. The beams can be designed as both end fixed or simple beams. The load bearing capacity of a beam depends on each boundary condition. However, when the load bearing capacity of a beam is evaluated in fire tests, all kinds of beams are tested using simple beam conditions. In this study, an analytical method performed using heat transfer theory and heat stress analysis based on the mechanical and thermal properties of SS-400 steel at high temperature. This method was used to clarify the differences between the two types of boundary conditions at normal and high temperature. The results show that the load bearing capacity of a both-end fixed beam at high temperature is superior to that of a simple beam. Therefore, the application of simple beam conditions in fire tests for evaluation of load bearing capacity is conservatively safe compared to fixed boundary conditions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.4
• /
• pp.734-742
• /
• 2016

Global warming and the depletion of fossil fuels have been caused by decades of reckless development. Wind energy is one form of renewable energy and is considered a future energy source. The wind tower is designed with a fundamental frequency in the soft-stiff design between the 1P and 3P range to avoid resonance. Usually, to perform natural frequency analysis of a wind tower, the boundary condition is set to the Fixed-End, and soil-pile interaction is not considered. In this study, consideration of the effect of soil-pile interaction on the wind tower was included and the difference in the natural frequency was studied. The fixed boundary condition was not affected by the soil condition and depth of the pile and the coupled spring boundary condition was unaffected by the depth of pile but affected by the depth of the pile, and the Winkler spring boundary condition is affected by both the soil condition and the depth of the pile. Therefore, the coupled spring boundary condition should be used in shallow depth soil conditions because the soil condition does not take the shallow depth soil into consideration.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.32 no.5
• /
• pp.287-296
• /
• 2019

In this study, the effect of ground boundary conditions on the evaluation of blast resistance performance of precast arch structures was evaluated by a numerical analysis method. Two types of boundary conditions, namely, fixed boundary conditions and a perfectly matched layer (PML) were applied to numerical models. Blast loads that were much higher than the design load of the target structure were applied to compare the effects of the boundary conditions. The distribution and path of the ground explosion pressure, structural displacement, fracture of concrete, stress of concrete, and reinforcing bars were compared according to the ground boundary condition settings. As a result, the reflecting pressure shock wave at the ground boundaries could be effectively eliminated using PML elements; furthermore, the displacement of the foundation was reduced. However, no distinct difference could be observed in the overall structural behavior including the fracture and stress of the concrete and rebar. Therefore, when blast simulations are performed in the design of protective structures, it is rational to apply the fixed boundary condition on the ground boundaries as conservative design results can be achieved with relatively short computation times.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.1
• /
• pp.132-141
• /
• 1992

The critical condition for onset of Benard convection with variable viscosity .nu.=.nu.$_{0}$exp(-CT) has been obtained using a linear stability theory. The bottom wall is rigid while the upper surface may be either free or rigid. The two boundaries are subject to convective heat transfer. The critical Rayleigh numbers are presented up to maximum viscosity ratio of 3000. It is greater for smaller upper and/or lower surface Biot numbers. Its dependence on the viscosity ratio is complicated. However, a simple sublayer theory is found to be applicable for extremely large viscosity ratio. In such cases, the critical Rayleigh number and the critical wave number are functions of viscosity ratio and lower surface Biot number.r.

• Journal of the Korean Society of Safety
• /
• v.12 no.4
• /
• pp.220-229
• /
• 1997

The differential quadrature method (DQM) is applied to computation of the eigenvalues of the equations governing in plane and out-of-plane buckling. In-plane buckling and twist-buckling under uniformly distributed radial loads are investigated by this method. Critical loads are calculated for various end conditions and opening angles. Results are compared with existing exact solutions where available. The differential quadrature method gives good accuracy even when only a limited number of grid points is used. New results are given for two sets of boundary conditions not previously considered for this problem clamped-clamped and clamped simply supported ends.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.3 no.1
• /
• pp.9-20
• /
• 1999

An accurate method is presented for flexural vibrations of rhombic plates having all combinations of clamped and free edge conditions. The prime focus here is that the analysis explicitly considers the bending stress singularities that occur in the two opposite, clamped-free corners having obtuse angles of the rhombic plates. Accurate non-dimensional frequencies and normalized contours of the vibratory transverse displacement are presented for rhombic plates having a large enough obtuse angle of 165$^{\circ}$, so that a significant influence of clamped-free corner stress singularities may be understood.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.2 no.3 s.6
• /
• pp.119-125
• /
• 2002

The objective of this study is to evaluate elastic modulus of bridge-axis direction for optimum structure system in the cable-stayed bridge design. In numerical example of this study, a slight change in axis direction elastic modulus causes major modifications of the bridge characteristics when it is $1\times10^4$ tonf/m/bearing or less. Therefore, the elastic modulus was set at this lower limit of $1\times10^4$ tonf/m/bearing where the strength of the entire bridge system is still determined by girder strength and the entire system is insensitive to variations in elastic modulus. Besides, cable-stayed bridge with freely supported girders have slightly longer vibration periods in the horizontal direction for earthquake forces.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.2 s.45
• /
• pp.221-230
• /
• 2000

Checking the stability of anisotropic plates with free edges, it is impossible that buckling loads and modes are found via existing classical methods about various loads and boundary conditions. For solving this problems. finite difference method(FDM) is used to analyze the buckling behaviors for arbitrary boundary conditions. Using FDM, it is difficult to treat the fictitious points on free edges. So, this paper analyzes buckling behaviors of analytic models with one edge free and the other edges clamped and with opposite two edges free and other two edges clamped. The various buckling loads and mode characteristics through numerical results are given for buckling behaviors of anisotropic plates on free edges.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.37 no.2
• /
• pp.53-63
• /
• 1995

본 논문의 다경간 연속아치의 자유진동에 관한 연구이다. 다경간 연속아치의 고유진 동수 및 진ㄷㅇ형을 산출하기 위하여 내부지점의 지점조건에 다른 경계조건식을 유도하였다. 아치의 선형은 포물선을 택하였으며, 회전-로울러-회전, 고정-회전-고정의 지점 조건을 갖는 2경간 연속아치에 대한 수치해석 결과를 제시하였다. Runge-Kutta maethod을 이용 하였다. 실제 수치해석예에서는 회전관성이 고유진동수에 미치는 영향을 고찰 하였으며, 무차원 고유진동수와 아치높이 지간길이비 및 세장비 사이의 관계를 분석하였다. 또한 실험을 토아여 이론적인 해석결과를 검증하였다.

• The Journal of Engineering Geology
• /
• v.32 no.1
• /
• pp.143-155
• /
• 2022

In this study, the response acceleration amplification according to different conditions was analyzed by changing the boundary condition of the soil called LSB (Laminar Shear Box), which is placed on a 1 g shaking table for earthquake simulation experiments. Experiments were carried out with different boundary conditions by fixing both sides of the LSB, and two samples were tested by installing an accelerometer at the same location. In addition, using DEEPSOIL v7 program, a one-dimensional ground response analysis was performed to compare and analyze with the free field condition. As a result, it was confirmed that the acceleration was amplified as it went from the lower layer to the upper layer, and as a result of comparing it with the ground response analysis, it was confirmed that it appeared similar to the analysis under the free field condition. As a result of the SA (Spectrum acceleration) analysis, a result similar to that of the ground response analysis was obtained, and in the case of fixing, it was confirmed that the PSA (Peak Spectral Acceleration) was further amplified.