• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.6
• /
• pp.131-137
• /
• 2013

The barrel distortion makes serious problems in a wide-angle camera employing a lens of a short focal length. This paper presents a low-complexity hardware architecture for a real-time barrel distortion corrector and its implementation. In the proposed barrel distortion corrector, the conventional algorithm is modified so that the correction is performed incrementally, which results in the reduction of the number of required hardware modules for the distortion correction. The proposed barrel distortion corrector has a pipelined architecture so as to achieve a high-throughput correction. The correction rate is 74.86 frames per sec at the operating frequency of 314MHz in a $0.11{\mu}m$ CMOS process, where the frame size is $2048{\times}2048$. The proposed barrel distortion corrector is implemented with 14.3K logic gates.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38B no.1
• /
• pp.34-45
• /
• 2013

Due to its self-configuring nature, the tactical mobile ad hoc network is used for communications between tactical units and the command and control center (CCC) in battlefields, where communication infrastructure is not available. However, when a tactical unit moves far away from the CCC or there are geographical constraints, the data link between two communicating nodes can be broken, which results in an invalid data route from the tactical units to CCC. In order to address this problem, in this paper we propose a hierarchical connectivity maintenance scheme, namely ADLCoM (Autonomous Data Link Connectivity Maintenance). In ADLCoM, each tactical unit has one or more GW (gateway), which checks the status of data links between tactical units. If there is a possibility of link breakage, GWs request ground or aerial unmanned vehicles to become a relay for the data link. The simulation results, based on tactical scenarios, show that the proposed scheme can significantly improve the network performance with respect to data delivery ratio.

• The Journal of the Korea Contents Association
• /
• v.9 no.8
• /
• pp.49-56
• /
• 2009

In this paper, we propose a method of energy level, node degree and selection information based CDS(Connected Dominating Set) construction algorithm for more efficient routing in ad-hoc wireless networks. Constructing CDS in ad-hoc wireless network, it is necessary to make more efficient algorithm that is faster, more simple and has low power consumption. A CDS must be minimized because nodes in the CDS consume more energy in order to handle various bypass traffics than nodes outside the set. It is better not to reconstruct CDS after constructing the most efficient CDS. To overcome this problem, we proposed the CDS construction algorithms based on EL+ND+Sel method. We compared and estimated the performance in each situation of EL + ND and EL + ND + Sel.

• Journal of KIISE:Databases
• /
• v.27 no.2
• /
• pp.227-237
• /
• 2000

A Web database System is a large-scaled multimedia application system that has multimedia processing facilities and cooperates with relational/Object-Oriented DBMS. Conventional hypertext modeling methods and DB gateway have limitations for Web database because of their restricted versatile presentation abilities and inefficient concurrency control caused by bottleneck in cooperation processing. Thus, we suggest a Dynamic Navigation Model & Virtual Graph Structure. The Dynamic Navigation Model supports implicit query processing and dynamic creation of navigation spaces, and introduce node-link creation rule considering navigation styles. We propose a mapping methodology between the suggested hypertext model and the relational data model, and suggest a dynamic allocation scheduling technique for query processing server based on weighted value. We show that the proposed technique enhances the retrieval performance of Web database systems in processing complex queries concurrently.

• Journal of Korea Multimedia Society
• /
• v.11 no.10
• /
• pp.1385-1391
• /
• 2008

The network-based IP mobility solution - Proxy MIPv6 provides a mobile node with local mobility support without requiring MIPv6 functionality of the mobile node by using two principle functional entities, LMA (Local Mobility Anchor) and MAG (Mobile Access Gateway) located in a Proxy MIPv6 domain. Yet, in case that a mobile node moves into a mobile network located in the domain, the mobile node can't receive the local mobility support any more because it can't communicate with the MAG. This paper proposes a scheme to support nested network mobility in a Proxy MIPv6 domain by adding MAG functionality to a mobile router in the mobile network and evaluates the performance of the proposed scheme. Performance analysis shows that the proposed scheme can increase the performance of handover delay, signaling costs, and packet loss ratio.

• Journal of the Korean Magnetics Society
• /
• v.19 no.2
• /
• pp.67-73
• /
• 2009

The changes of geomagnetic flux density distribution on the ground surface by underground empty spaces had been investigated through the variations of the soil density and measuring heights. The geomagnetic flux density distributions were monitored for the surfaces of different density, sink-hole and tunnel by fluxgate-type magnetometer. The underground empty space and low soil density decreased the geomagnetic flux densities, which were decreased from the boundary of raw and low-density (empty) grounds, and showed the lowest value at the center of low-density (empty) ground. The decreases of geomagnetic flux density by underground empty spaces could be found at the surface with the tunnel located at 80 m underground. And, the underground defects of empty spaces, low density zone, fracture zone and sink holes could be monitored by the phenomena of this decreasing flux density.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.751-753
• /
• 2011

Pulse Oximeter is used two different wavelength light sources. Two signals measured by light transmission in the body parts. SPo2 is calculated from the measured signal. These optical methods is have the light absorption properties of oxygen in the blood. SPo2 is to be called vital signs of $5^{th}$and important in modern medical. But, exist pulse oximeter was used just user for viewing the SPo2. That was a lack of used communication Monitoring function. In this paper using the Bluetooth feature on the exist pulse oximeter to communicate with the outside of the Gateway for design medical devices standards protocol IEEE 11073-10404 built-in pulse oximeter. Also user can be monitoring the U-Health Gateway through the pass SPo2 information.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.6
• /
• pp.89-95
• /
• 2008

In this paper, we designed a low power face detection hardware and analysed its power consumption. The face detection hardware was fabricated using Samsung 0.18um CMOS technology and it can detect multiple face locations from a 2-D image. The hardware is composed of 6 functional modules and 11 internal memories. We introduced two operating modes(SLEEP and ACTIVE) to save power and a clock gating technique was used at two different levels: modules and registers. In additional, we divided an internal memory into several pieces to reduce the energy consumed when accessing memories, and fully utilized low power design option provided in Synopsis Design Compiler. As a result, we could obtain 68% power reduction in ACTIVE mode compared to the original design in which none of the above low power techniques were used.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.3
• /
• pp.8-16
• /
• 1999

This paper describes a VLSI design of Reed-Solomon(RS) decoder using the modified Euclid algorithm, with the main theme focused on the $\textit{GF}(2^8)$. To get area-efficient design, a number of new architectures have been devised with maximal register and Euclidean ALU unit sharing. One ALU is shared to replace 18 ALUs which computes an error locator polynomial and an error evaluation polynomial. Also, 18 registers are shared to replace 24 registers which stores coefficients of those polynomials. The validity and efficiency of the proposed architecture have been verified by simulation and by FLEX$^TM$ FPGA implementation in hardware description language VHDL. The proposed Reed-Solomon decoder, which has the capability of decoding RS(208,192,17) and RS(182,172,11) for Digital Versatile Disc(DVD), has been designed by using O.6$\mu\textrm{m}$ CMOS TLM Compass$^TM$ technology library, which contains totally 17k gates with a core area of 2.299$\times$2.284 (5.25$\textrm{mm}^2$). The chip can run at 20MHz while the DVD requirement is 3.74MHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.12
• /
• pp.36-42
• /
• 2009

This paper proposes the high-performance pipeline architecture for modified Booth multipliers. The proposed multiplier circuits are based on modified Booth algorithm and pipeline architecture which are the most widely used techniques to accelerate the multiplication speed. In order to implement the optimally pipelined multipliers, many kinds of experiments have been conducted. The experimental results show that the speed improvement gain exceeds the area penalty and this trend is manifested as the number of pipeline stages increases. It is also important to insert the pipeline registers at the proper positions. We described the proposed modified Booth multiplier circuits in Verilog HDL and synthesized the gate-level circuits using 0.13um standard cell library. The resultant multiplier circuits show better performance than others. Since they operate at GHz ranges, they can be used in the application systems requiring extremely high performance such as optical communication systems.