• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.6
• /
• pp.1413-1422
• /
• 2012

Adaptive back stepping control technique may provide robust control characteristics under parameter perturbation caused by changing external condition. In order to synthesize a high-precision velocity controller for IPMSM(Interior Permanent Magnet Synchronous Motor) using this method, the period of control loop should be very small. However, because of the resolution of the encoder for speed measurement, control cycle is limited, which makes it difficult to improve the performance of the controller. This paper proposes a velocity controller design method based on nonlinear adaptive back-stepping method to accomplish fast and accurate performance. Here, an EKF(Extended Kalman Filter) method is incorporated for the estimation of the motor speed into the design of a speed controller using adapted back-stepping control technique. The performance of the proposed controller is demonstrated through simulation using PSIM.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.5
• /
• pp.361-368
• /
• 2015

This paper deals with a robust fine seek controller design problem with multiple constraints using a genetic algorithm. A robust $H\infty$ constraint is introduced to attenuate effectively velocity disturbance caused by the eccentric rotation of the disk. A weighting function is optimally selected based on the estimation of velocity disturbance and the estimated minimum velocity loop gain. A robust velocity loop constraint is considered to minimize the variances of the velocity loop gain and bandwidth against the uncertainties of fine actuator. Finally, a robust fine seek controller is obtained by solving a genetic algorithm with an LMI condition and an appropriate objective function. The proposed controller design method is applied to the fine seek control system of a DVD recording device and is evaluated through the experimental results.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.79.2-79.2
• /
• 2011

플라이 휠 에너지 저장장치(Flywheel Energy Storage System: FESS)는 전기 에너지를 회전 운동 에너지로 저장하였다가 필요시 회전 운동에너지를 전기 에너지로 변환하여 재사용 가능한 에너지 저장장치 이다. 최근 전력 변환 기술의 발전으로 인하여 플라이휠 에너지 저장 장치의 에너지 입출력 속도가 빨라지고 대용량의 에너지를 저장할 수 있게 되었다. 본 논문에서는 이러한 플라이휠 에너지 저장 장치의 전력 입출력 특성을 이용하여 전력 시스템에서 발생하는 저주파 진동(Low frequency oscillation)을 억제하는 방안을 제시 하여 안정도를 향상 시키고자 하였다. 전력 시스템은 발전조건, 전송조건, 부하조건에 따라 동작 조건이 지속적으로 변하고 있다. 이러한 동작 환경 변화는 전력 시스템에 대한 수학적인 표현과 실제 전력계통간의 차이가 발생하기 때문에 정확한 제어 목적을 달성하기가 힘들다. 따라서 본 논문에서는 제어기 설계 단계에서 전력 계통의 불확실성을 고려할 수 있는 $H_{\infty}$ 제어 기법을 이용하여 플라이휠 에너지 저장장치를 위한 강인 제어기를 설계 하였다. 제안한 플라이휠 에너지 저장장치의 강인 제어기의 유용성을 입증하기 위하여 1기 무한대 모선에 적용한 결과를 비선형 시뮬레이션을 통하여 다양한 외란이 발생한 경우에 외란 억제 성능과 강인성에 대하여 고찰 하였으며, 제안한 방식이 기존의 전력계통 안정화 장치(Power system stabilizer: PSS) 보다 효율적이며 전력계통의 안정도 향상에 크게 기여함을 보이고자 하였다.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.6
• /
• pp.77-82
• /
• 2005

This paper is proposed fuzzy neural network(FNN) and artificial neural network(ANN) based on the vector controlled induction motor drive system. The hybrid combination of fuzzy control and neural network will produce a powerful representation flexibility and numerical processing capability. Also, this paper is proposed control and estimation of speed of induction motor using fuzzy and neural network. The back propagation neural network technique is used to provide a real time adaptive estimation of the motor speed. The error between the desired state variable and the actual one is back-propagated to adjust the rotor speed, so that the actual state variable will coincide with the desired one. The back propagation mechanism is easy to derive and the estimated speed tracks precisely the actual motor speed. This paper is proposed the experimental results to verify the effectiveness of the new method.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.9 no.1
• /
• pp.59-69
• /
• 2001

The rotor blade is modeled using a composite box beam with arbitrary wall. The active constrained damping layers are bonded to the upper and lower surfaces of the box beam to provide active and passive damping. A finite element model, based on a hybrid displacement theory, is used in the structural analysis. The theory is capable of accurately capturing the transverse shear effects in the composite primary structure, the viscoelastic and the piezoelectric layers within the ACLs. A reduced order model is derived based on the Hankel singular value. A linear quadratic Gaussian (LQG) controller is designed based on the reduced order model and the available measurement output. However, the LQG control system fails to stabilize the perturbed system although it shows good control performance at the nominal operating condition. To improve the robust stability of LQG controller, the loop transfer recovery (LTR) method is applied. Numerical results show that the proposed controller significantly improves rotor aeromechanical stability and suppresses rotor response over large variations in rotating speed by increasing lead-lag modal damping in the coupled rotor-body system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.2
• /
• pp.138-147
• /
• 1998

This paper describes design and implementation results of a fuzzy logic speed controller of EV(Electric vehicle)'s induction motor for the purpose of realizing comfortable driving. The fuzzy controller is suitable for speed control of EV since that without detailed knowledge about the induction motor, it is easier to design a well-performing speed control system with good stability. PWM wave for driving the induction motor is generated by space vector modulation method and all the control algorithms are realized digitally. The results of experiment show excellence of the proposed system and that the proposed system is appropriate to control the speed of induction motor for commercial EVs.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.7
• /
• pp.65-73
• /
• 2006

This paper presents speed control of IPMSM drive using neural network(NN) PI controller. In general, PI controller in computer numerically controlled machine process fixed gain. They may perform well under some operating conditions, but not all. To increase the robustness of fixed gain PI controller, NNPI controller proposes a new method based neural network. NNPI controller is developed to minimize overshoot rise time and settling time following sudden parameter changes such as speed, load torque and inertia. Also, this paper is proposed speed control of IPMSM using neural network and estimation of speed using artificial neural network(ANN) controller. The back propagation neural network technique is used to provide a real time adaptive estimation of the motor speed. The results on a speed controller of IPMSM are presented to show the effectiveness of the proposed gain tuner. And this controller is better than the fixed gains one in terms of robustness, even under great variations of operating conditions and load disturbance.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.20 no.4
• /
• pp.476-482
• /
• 2010

In this paper, we propose a robust path tracking control method for autonomous underwater vehicle with variable speed. The proposed path tracking controller consists of a kinematic controller and a dynamic controller. First, the kinematic controller computes the surge speed and yaw rate to follow the reference path with variable speed. Then the dynamic controller controls the thrust force and yaw torque to move the AUV actually. In the dynamic control, we assume that the sway speed is a disturbance. In addition the dynamic controller is designed based on sliding mode conrol. We also demonstrate the stability of the proposed control method by Lyapunov stability theory. Finally, simulation results illustrate the performance of the proposed control method.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.12 no.4
• /
• pp.70-74
• /
• 1998

Robust control for DC motor is needed according to the highest precision of industrial automation. However, when a motor control system with PID contoller has an effect of load disturbance, it is very difficult to guarantee the robustness of control system. In this paper, PID-supervision hybrid control methods for motor control system (without the supervisory controller) is stable in the sense that the error is inside the constraint set, the supervisory control is idle. If the error hits the boundary of the constraint, the supervisory controller beings operation to force the error back to the constraint set. We prove that the PID-supervision hybrid control system is globally stable in the sense that the error is guaranteed to be within the tolerance limits specified by the system designer.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.8
• /
• pp.140-147
• /
• 2015

In this paper, we propose a state feedback robust controller of 2-axis gimbal system which have bounded parametric uncertainty. The proposed controller is robust against dynamics variations of gimbal system and contains a dynamic compensator in order to improve a steady state error and a transient response. The stability of the closed-loop system is proved by Lyapunov approach. The performance of the proposed method is demonstrated by simulation on a 2-axis gimbal system.