• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.1
• /
• pp.132-141
• /
• 1992

The critical condition for onset of Benard convection with variable viscosity .nu.=.nu.$_{0}$exp(-CT) has been obtained using a linear stability theory. The bottom wall is rigid while the upper surface may be either free or rigid. The two boundaries are subject to convective heat transfer. The critical Rayleigh numbers are presented up to maximum viscosity ratio of 3000. It is greater for smaller upper and/or lower surface Biot numbers. Its dependence on the viscosity ratio is complicated. However, a simple sublayer theory is found to be applicable for extremely large viscosity ratio. In such cases, the critical Rayleigh number and the critical wave number are functions of viscosity ratio and lower surface Biot number.r.

• Journal of KSNVE
• /
• v.11 no.1
• /
• pp.141-146
• /
• 2001

This paper deals with an application of Magneto-Rheological (MR) fluid to a small size mount for precision equipment of automobiles. MR fluid is known as a class of functional fluids with controllable apparent viscosity of fluid by the applied magnetic field strength. A typical MR fluid is a suspension where pure iron particles of 1-20 (m in diameter are dispersed in a liquid such as mineral oil or silicone oil, at the concentration of 20 - 40 vol%. Electro magnetic coil is installed at the bottom of a variable-damping mount filled with MR fluid, and performance of the mount was investigated experimentally. Furthermore, the Properties of the MR Mount on experimental study were explained analytically by mechanical model of the MR mount.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.170-173
• /
• 2002

시스템이 슬라이딩모드의 존재조건을 만족하는 경우, 전동기의 상태가 전동기의 파라미터에 의존하지 않고 결정되는 절환 초평면에 수렴하기 때문에 파라미터에 불감한 응답을 나타낸다. 본 연구는 소형 유도전동기에 의한 외란 및 파라미터의 변동에 대하여 로바스트(robust)와 동시에 정확한 응답을 나타내는 교류서보 전동기 구동시스템을 실현하는 것이다. 이를 실현하기 위해서 가변구조 제어이론에 기초한 슬라이딩모드 제어를 적용하여 유도전동기 자계 슬립주파수형 벡터제어를 실현한다. 이상적인 전동기에 대한 시뮬레이션의 결과에 의해서 관성, 점성마찰계수, 부하 토오크 등 의 파라미터의 변동 및 외란에 대하여 로바스터성이 있다는 것을 알 수 있고 슬라이딩모드 제어의 도입이 교류전동기 서보제어에 유효한 것을 확인하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.374-378
• /
• 2003

This paper presents investigation of damping characteristics of squeeze mode type MR (Magneto-Rheological) mount experimentally. Since damping property of the MR fluid is changed by variation of the applied magnetic field strength, squeeze mode type MR mount proposed in the study has variable damping characteristics according to the applied magnetic field s strength. In the present work, the performance of the mount was experimentally investigated according to the magnetic field strength and exciting frequencies. The experimental results present that the MR mount can effectively reduce the vibration in a wide range of frequency by controlling the applied electromagnetic filed strength. Viscous damping and stiffness coefficients of the MR mount tend to be changed according to the variation of the applied currents in this study and MR effect is reduced by increasing exciting frequency.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.6
• /
• pp.490-495
• /
• 2003

This paper presents investigation of damping characteristics of squeeze mode type MR (magneto-rheological) mount experimentally. Since damping property of the MR fluid is changed by variation of the applied magnetic field strength, squeeze mode type MR mount proposed in the study has variable damping characteristics according to the applied magnetic field strength. In the present work, the performance of the mount was experimentally Investigated according to the magnetic field strength and exciting frequencies. The experimental results present that the MR mount can effectively reduce the vibration in a wide range of frequency by controlling the applied electromagnetic field strength. Viscous damping and stiffness coefficients of the MR mount tend to be changed according to the variation of the applied currents in this study and MR effect is reduced by increasing exciting frequency.

• Journal of KSNVE
• /
• v.9 no.1
• /
• pp.121-130
• /
• 1999

Generally, A Dynamic Absorber by using Active viscous Damping is highlighted for effective suspension system, such as improved ride comfort and handling in the market. Lately, this system based on the Sky-Hook damper theory is introduced by the name of "Active Dynamic Absorber" to us. This system has an excellent performance in contrast to Passive. Adaptive Dynamic Absorber, besides having low cost components of system, low energy consumption. light weight of system. In this viewpoint. most of car-maker will adopt this system in the near future. For this reason, we developed Dynamic Absorber by using Active viscous Damping which is equipped with continuously variable Dynamic Absorber and Control logic consisting Filter and Estimator. control apparatus of Dynamic Absorber operated by 16-bit microprocessor of high performance. variable device of viscous Damping. G-sensor so on. In this paper. several important points of development procedure for realizing this system will be described with results in which is obtained from experiment by simulation and Full car test in Proving ground. respectively.pectively.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.3
• /
• pp.275-281
• /
• 2015

In this study, vertical motion of a Tuned Liquid Column Damper(TLCD) is measured by a variable voltage measurement system in the electric field and design parameters of the TLCD are determined. First, nonlinear damping term of the TLCD is replaced as the equivalent viscous damping term. The natural frequency and damping ratio of dynamic characteristics of the TLCD are verified. In addition, a novel liquid level measurement system is developed for measuring vertical motion of the TLCD. For the experimental achievement, experimental characterizations of natural frequency and damping ratio of the TLCD are undertaken utilizing the developed variable voltage sensing. Also, shake table testing is performed to determine the dynamic characteristics of the TLCD. As a result, the feasibility of the proposed liquid level measurement system is verified by comparison with the capacitive type wavemeter.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.464-467
• /
• 2002

This paper presents investigation of damping characteristics of squeeze mode type MR (magneto-Rheological) mount experimentally. Since damping property of the MR fluid is changed by variation of the applied magnetic field strength, squeeze mode type MR mount proposed in the study has variable damping characteristics according to the applied magnetic field strength. Impact and excitation tests were performed to investigate the dynamic properties of squeeze mode type MR mount. Responses of the mount were compared in proportion to the applied magnetic field strength. The experimental results show that the mount can effectively reduce vibration amplitude in a wide frequency range by changing the applied magnetic field strength.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1990.06a
• /
• pp.32-44
• /
• 1990

유압 Vane pump는 carming, rotor, vane에 의하여 둘러싸인 공간체적이 rotor의 회전과 함께 변화하면서 pump 작용을 한다. 즉 공간체적이 증가하는 동안은 유압이 저압으로 되어 흡입구에서 유압유를 흡입하고 vane의 존환점 (vane이 가장 많이 출한 점)을 지나면 공간용적이 감소하여 유압류는 고압으로 될 수 있도록 되어있다. 이때 vane은 관성력과 점성력 그리고 유압류의 압력에 의한 힘으로 vane 선단이 캠링의 내면에 밀착되어 회전하도록 되어있다. 유압 vane pump 베인 선단부의 윤활문제와 관련된 지금까지의 연구로서는 Hibi 등에 의한 압력평형형 베인모터, W.D Beck, T.C Edwards에 의한 베인형 콤푸렛셔 Ujiie 등에 의한 베인형 진공펌프, Ueno 등에 의한 가변용량형 베인펌프의 마찰특성에 관한 연구 및 베인 이간 현상에 관한 실험적 연구가 있다. 그러나 이와 같은 연구들의 베인과 캠링 슬라이딩 부분에 관한 취급들은 베인선단 슬라이딩 부분에 가해지는 변동가중이 불명확했기 때문데, 단순히 슬라이딩 부분의 면적이 작다는 이유로 단성유체 윤활상태일 것이라는 확정을 하였을 뿐, 실제적으로 어느 정도의 윤활 상태를 파악하기 위하여 회전하는 vane의 가학적인 거동을 확실하게 규명하고자 함이 본 연구의 목적이다.

• Journal of Korea Game Society
• /
• v.14 no.3
• /
• pp.55-62
• /
• 2014

In particle-based fluid simulation, applying sudden power to particle raise unnatural flow when wave is breaking. To solve this problem, we have used an linear interpolation technique that interpolate between fluid particle by subdividing the time interval in the previous work. Acceleration vector of the particle with increased pressure in boundary could change smoothly. However, particle looks like flow with viscosity because the number of the minimum samples to interpolate increases. We propose an weighted-interpolation technique to represent the realistic movement of fluid. it is accumulating that has added and assigned different weights to the previous acceleration vector and current one repeatedly. weighted-interpolation technique using less minium samples to flow than linear interpolation, so it can solve the problem which particle looks like flow with viscosity.