• Environmental Engineering Research
• /
• 제11권2호
• /
• pp.84-90
• /
• 2006

UV-catalytic oxidation technique was applied for the treatment of bio-refractory character of the leachate, which is generally present in the form of adsorbable organic halogens (AOX). Destruction of AOX was likely to be governed by pH adjustment, quantitative measurement of oxidants, and the selection of oxidation model type. Peroxide induced degradation ($UV/H_2O_2$) facilitated the chemical oxidation of organic halides in acidic medium, however, the system showed least AOX removal efficiency than the other two systems. Increased dosage of hydrogen peroxide (from 0.5 time to 1.0 time concentration) even did not contribute to a significant increase in the removal rate of AOX. In ozone induced degradation system ($UV/O_3$), alkaline medium (pH 10) favored the removal of AOX and the removal rate was found 11% higher than the rate at pH 3. Since efficiency of the $UV/O_3$ increases with the increase of pH, therefore, more OH-radicals were available for the destruction of organic halides. UV-light with the combination of both ozone and hydrogen peroxide ($UV/H_2O_2$ 0.5 time/$O_3$ 25 mg/min) showed the highest removal rate of AOX and the removal efficiency was found 26% higher than the removal efficiency of $UV/O_3$. The system $UV/H2O_2/O_3$ got the economic preference over the other two systems since lower dose of hydrogen peroxide and relatively shorter reaction time were found enough to get the highest AOX removal rate.

• Environmental Engineering Research
• /
• 제16권3호
• /
• pp.131-136
• /
• 2011

The degradation of 30 pharmaceuticals and personal care products (PPCPs) subjected to $O_3$, $O_3$/UV, and $O_3/H_2O_2$ treatments were investigated using semi-batch tests and evaluated by their pseudo-first-order rate constants. The additional application of UV or $H_2O_2$ during $O_3$ treatment significantly improved the degradation rate of most of the PPCPs. At the same $O_3$ feed rate, $O_3$/UV treatment exhibited much higher PPCP degradation efficiency than that of $O_3$ treatment. This was probably due to degradation of the PPCPs by $O_3$, direct UV photodegradation, and OH radicals that formed from the photodegradation of $O_3$ during $O_3$/UV treatment. PPCP degradation by $O_3$ was also promoted by adding $H_2O_2$ during the $O_3$ treatment. However, when the initial $H_2O_2$ concentration was high during $O_3$ treatment, OH radicals were likely to be scavenged by excess $H_2O_2$, leading to low PPCP degradation. Therefore, it is important to determine the appropriate $H_2O_2$ dosage during $O_3$ treatment to improve PPCP degradation when adding $H_2O_2$ during $O_3$ treatment.

• 대한환경공학회지
• /
• 제22권2호
• /
• pp.241-249
• /
• 2000

난분해성 폐수인 사진현상폐수의 $UV/H_2O_2$ 및 $H_2O_2$의 고급산화에 의한 오염물질의 제거 실험을 실시하였다. $UV/H_2O_2$ 산화에서 $H_2O_2$의 분해로 $OH^-$ 라디칼이 발생되는데 파장 190~300 nm의 UV가 반응의 촉매 역할을 한다. $OH^-$ 라디칼은 수명은 짧으나 강력한 산화력을 갖고 있는데, 이 산화력은 폐수처리에서 폐수나 액상 폐기물의 유기물질을 제거하는데 이용된다. 본 연구에서 기존의 tube형 반응조의 단점을 보완한 UV-자유반사 반응조를 제작하여 사용하였으며 UV원으로는 수은 고압램프가 이용되었다. 본 실험에서는 반응시간과 $H_2O_2$ 주입량 및 pH 변화에 따른 오염물의 처리효율의 변화를 조사하였는데 $H_2O_2$의 주입량이 증가할수록 처리효율이 높았으나 그 차이는 미미하였으며, pH 8에서 보다는 3에서 처리효율이 약간 높았으나 그 차이 역시 크지 않았다. 본 연구에서 사진현상폐수 처리의 적정 운전조건은 pH 8, $H_2O_2$ 주입량은 유입수의 COD를 기준으로 한 1.3배 화학량론적 주입으로 나타났는데, 5시간의 처리에서 $COD_{Cr}$, TOC 및 색도의 제거효율은 각각 약 47.5%, 75.0% 및 91.5%로 나타났다. 반응 후 생분해성의 지표인 BOD/COD 비는 초기 0.04에서 0.21로 약 5.3배 증가하였다.

• 한국전기전자재료학회논문지
• /
• 제25권2호
• /
• pp.153-158
• /
• 2012

We use UV(ultraviolet)-$O_3$ treatment to increase the surface area and porosity of $TiO_2$ films in dye-sensitized solar cells (DSSCs). After the UV-$O_3$ treatment, surface area and porosity of the $TiO_2$ films were increased, the increased porosity lead to amount of dye loading and solar conversion efficiency was improved. Field emission scanning electron microscopy images clearly showed that the nanocrystalline porosity of films were increased by UV-$O_3$ treatment. The Brunauer, Emmett, and Teller surface area of the $TiO_2$ films were increased from $0.71cm^2/g$ to $1.31cm^2/g$ by using UV-$O_3$ treatment for 20 min. Also, UV-$O_3$ treatment of $TiO_2$ films significantly enhanced their solar conversion efficiency. The efficiency of the films without treatment was 4.9%, and was increased to 5.6% by UV-$O_3$ treatment for 20 min. Therefore the process enhanced the solar conversion efficiency of DSSCs, and can be used to develop high sensitivity DSSCs.

• 한국물환경학회지
• /
• 제33권6호
• /
• pp.736-743
• /
• 2017

In this study, 4-nonylphenol (4-NP), an endocrine disrupting chemical, was removed by ozone treatment processes under the various experimental conditions including UV irradiation, $TiO_2$ addition. The ozone flow rate and concentration were maintained at $1.0L{\cdot}min^{-1}$ and $70{\pm}5mg{\cdot}L^{-1}$. The pH, COD and TOC of the samples were obtained every 10 minutes for 60 minutes in laboratory scale batch reactor. We found that the combination of UV irradiation and $TiO_2$ addition for ozonation improves the removal efficiency of COD and TOC in 4-NP aqueous solution. In case of the $O_3/UV/TiO_2$ system, COD and TOC were greatly reduced to 85.3 ~ 94.0% and 89.2 ~ 97.2%, respectively. 4-NP degradation rate constants, $k_{COD}$ and $k_{TOC}$, were calculated based on the COD and TOC values. Significantly, $k_{COD}$ and $k_{TOC}$ were improved in the $O_3/UV/TiO_2$ treatment process compared with single $O_3$ process, because the oxidation and the mineralization of 4-NP were increased by generating of the hydroxyl radical. The $k_{COD}$ and $k_{TOC}$ were obtained to be $5.81{\times}10^{-4}{\sim}10.8{\times}10^{-4}sec^{-1}$ and $11.9{\times}10^{-4}{\sim}19.4{\times}10^{-4}sec^{-1}$ in the $O_3/UV/TiO_2$ process. Activation energy ($E_a$) of ozone oxidation reaction based on $k_{COD}$ and $k_{TOC}$ were increased in order of $O_3/UV/TiO_2$ < $O3/UV$ < $O_3/TiO_2$ < $O_3$ process. It was confirmed that the addition of $TiO_2$ and UV irradiation to the ozone oxidation reaction significantly reduced the $E_a$ value and the degradation of 4-NP.

• 한국환경과학회지
• /
• 제12권7호
• /
• pp.775-782
• /
• 2003

The photodegradations of pyrene, chrysene and benzo[a]pyrene that were similar in structure among polycyclic aromatic hydrocarbons (PAHs) were investigated with a low-pressure mercury lamp(the wavelength of 253.7 nm and UV output of 1.35${\times}$10$\^$-3/J/s). The optimum concentrations of TiO$_2$ and H$_2$O$_2$ on the photodegradation of pyrene, chrysene and benzo[a]pyrene were 1 g/L and 1.5${\times}$10$\^$-3/ M, respectively. By these optimum concentrations, their rates increased with increasing the concentration of TiO$_2$ and H$_2$O$_2$ because the amounts of OH radical formed increased, but for the higher concentrations than the optimum, their rates decreased with increasing those concentrations because the white turbidity phenomena occurs in case of TiO$_2$ and H$_2$O$_2$ acts as an OH radical inhibitor. The photodegradation rates among the photodegradation processes such as UV, UV/TiO$_2$, UV/H$_2$O$_2$, and UV/H$_2$O$_2$/TiO$_2$ decreased in the following sequences.: UV/H$_2$O$_2$/TiO$_2$> UV/H$_2$O$_2$> UV/TiO$_2$> UV.

• 한국물환경학회지
• /
• 제35권6호
• /
• pp.459-469
• /
• 2019

The ozonation of sulfamethoxazole (SMX) was performed at 20℃ using a pilot scale countercurrent bubble column reactor. Ozonation systems were combined with UV irradiation and TiO₂ addition. As the oxidation reaction proceeded in each treatment system, the pH of the sample decreased and in the O₃/UV/TiO₂ system, the pH change was the largest from 4.54 to 2.02. Under these experimental conditions, the scavenger impact of carbonate is negligible. The highest COD and TOC removal rate was observed in the O₃/UV/TiO₂ system due to the UV irradiation and the photocatalytic effect of TiO₂. Also, the highest mineralization ratio(ε) value is 0.2 in the O₃/UV/TiO₂ system, which means theoxidation capacity of the systems. The highest SMX degradation rate constants calculated by COD and TOC values (COD and TOC) were 2.15 × 10^-4 sec^-1 and 1.00 × 10^-4 sec^-1 in the O₃/UV/TiO₂ system, respectively. The activation energy (E_a) of ozone treatment follows the Arrhenius law. It was calculated based on _COD and _TOC. Each activation energy decreased in order of single O₃> O₃/TiO₂> O₃/UV > O₃/UV/TiO₂ system. The result showed that ΔH^≠ is more effective than ΔS^≠ in each SMX ozontaionsystem, that is characteristic of the common oxidation reaction.

• 대한환경공학회지
• /
• 제33권10호
• /
• pp.731-738
• /
• 2011

본 논문에서는 실험실적 규모의 순환형 회분식 반응기에서 수용액상 phenol을 처리하기 위해 $O_3/UV$ radiation, $O_3/Mg(OH)_2/UV$ radiation 그리고 $O_3/MgO/UV$ radiation 고급산화공정(AOPs)에 대한 연구를 수행하였다. 오존의 유량은 1.0 L/min, 오존 농도를 $150{\pm}10mg/L$로 일정하게 유지 하였으며, 산화반응에 나타나는 $COD_{Cr}$ 및 TOC를 각각 측정하였다. $20^{\circ}C$에서 $O_3/UV$ radiation, $O_3/Mg(OH)_2/UV$ radiation 그리고 $O_3/MgO/UV$ radiation에 대한 유사 1차 반응속도 상수는 각각 $9.31{\times}10^{-5}sec^{-1}$, $1.19{\times}10^{-4}sec^{-1}$ 그리고 $1.79{\times}10^{-4}sec^{-1}$, 활성화 에너지는 각각 $3.03kcal{\cdot}mol^{-1}$, $1.79kcal{\cdot}mol^{-1}$ 그리고 $4.23kcal{\cdot}mol^{-1}$ 로 나타났다. 수용액상에서 $Mg(OH)_2$와 MgO가 phenol의 분해와 COD의 제거에 현저한 촉진작용을 나타낸다는 것을 확인하였다. 이러한 실험 결과에 기초하여 $O_3/MgO/UV$ 시스템이 수용액상 phenol을 처리하기 위한 효율적이고 용이한 방법임을 제시하였다.

• 공업화학
• /
• 제22권6호
• /
• pp.617-622
• /
• 2011

축산폐수 혐기소화 유출수 중의 생물학적 난분해성 유기물의 분해를 위하여 오존 기반의 고도산화 기술을 적용하였다. 배출수의 COD 및 색도는 각각 9200~9500 mg/L 및 0.384 (400 nm)이고 1/10 희석하여 실험에 사용하였다. 공급 오존은 버블의 크기가 $13{\mu}m$인 마이크로버블 오존과 $105{\mu}m$인 일반 오존버블과의 차이를 고찰하였다. 마이크로버블 오존을 사용함으로써 오존의 용해도와 라디칼 생성량이 증가되었고 일반 오존버블에 비하여 COD 및 색도의 제거효율이 각각 85% 및 26% 향상되었다. 마이크로버블을 포함한 $O_3/UV$, $O_3/H_2O_2$, $O_3/UV/H_2O_2$의 조합을 비교한 결과 오존 단독 처리에 비하여 색도 제거율이 5~10% 정도 증가되었으며, 오존에 비하여 UV나 $H_2O_2$의 색도제거에 대한 기여가 크지 않음을 알 수 있었다. 반면 COD에 대해서는 $O_3/UV/H_2O_2$ 적용시 오존 단독에 비하여 2배 이상 제거율이 증가하였으며 UV보다는 $H_2O_2$의 기여도가 더 컸다. 한편 마이크로 오존의 사용시 증가된 용존오존 및 라디칼 활성으로 인하여 오존 공급을 중단한 후에도 UV 또는 $H_2O_2$를 적용함으로써 추가적인 COD 분해 효과를 지속적으로 유지할 수 있었다.

• 상하수도학회지
• /
• 제10권4호
• /
• pp.64-72
• /
• 1996

The effect of $O_3$, $O_3/pH$, and $O_3/H_2O_2$, $O_3/UV$, and $H_2O_2/UV$ advanced oxidation process(AOP) were investigated for the treatment of tetrachloroethylen(PCE) at various condition. The removal efficiency of 10, 20, and 30ppm PCE by ozonation were almost same, only about 60%. And pseudo first-order rate constants, ko for overall oxidation was about 0.097($min^{-1}$). In the $O_3/pH$ AOP experiment for the 20ppm PCE, the removal rate of PCE increased with the increase of pH. However, mineralization rate of PCE at pH 7 was higher than at pH 10. In the $O_3/H_2O_2$ AOP, the removal rate of PCE was the highest at peroxide-to-ozone dosage ratio of about 0.9, which PCE was removed over 99.95%. Despite 42% of PCE was directly photolyzed by the UV irradiation, the removal efficiency of PCE by $O_3/UV$ AOP was only about 70%. In $H_2O_2/UV$ AOP, the removal efficiency of PCE increased to about 98% in proportion to the $H_2O_2$ injection concentration at constant UV intensity of 5W/l.