• 한국전기전자재료학회논문지
• /
• 제22권3호
• /
• pp.248-251
• /
• 2009

We have investigated the effect of the quality of 1.3 um distributed feed back laser diode (DFB-LD) on the design of anti-reflection (AR) coatings. Optimal condition of AR coating to prevent internal feedback from both facets and reduce the reflection-induced intensity noise of laser diode was simulated with Macleod Simulator. Coating materials used in this work were ${Ti_3}{O_5}$ and $SiO_2$, of which design thickness were 105 nm and 165 nm, respectively. AR coating films were deposited by Ion-Assisted Deposition system. The electrical and optical properties of 1.3 um laser diode were characterized by Bar tester and Chip tester. Threshold current and slop-efficiency of DFB-LD were 27.56 mA 0.302 W/A. Far field pattern and wavelength of DFB-LD were $22.3^{\circ}(Horizontal){\times}24.4^{\circ}$ (Vertical), 1313.8 nm, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.236-236
• /
• 2008

(Bi,La)$Ti_3O_{12}$(BLT) thin film is one of the most attractive materials for ferroelectric random access memory (FRAM) applications due to its some excellent properties such as high fatigue endurance, low processing temperature, and large remanent polarization [1-2]. The authors firstly investigated and reported the damascene process of chemical mechanical polishing (CMP) for BLT thin film capacitor on behalf of plasma etching process for fabrication of FRAM [3]. CMP process could prepare the BLT capacitors with the superior process efficiency to the plasma etching process without the well-known problems such as plasma damages and sloped sidewall, which was enough to apply to the fabrication of FRAM [2]. BLT-CMP characteristics showed the typical oxide-CMP characteristics which were related in both pressure and velocity according to Preston's equation and Hernandez's power law [2-4]. Good surface roughness was also obtained for the densification of multilevel memory structure by CMP process [3]. The well prepared BLT capacitors fabricated by CMP process should have the sufficient ferroelectric properties for FRAM; therefore, in this study the electrical properties of the BLT capacitor fabricated by CMP process were analyzed with the process parameters. Especially, the effects of CMP pressure, which had mainly affected the removal rate of BLT thin films [2], on the electrical properties were investigated. In order to check the influences of the pressure in eMP process on the ferroelectric properties of BLT thin films, the electrical test of the BLT capacitors was performed. The polarization-voltage (P-V) characteristics show a decreased the remanent polarization (Pr) value when CMP process was performed with the high pressure. The shape of the hysteresis loop is close to typical loop of BLT thin films in case of the specimen after CMP process with the pressures of 4.9 kPa; however, the shape of the hysteresis loop is not saturated due to high leakage current caused by structural and/or chemical damages in case of the specimen after CMP process with the pressures of 29.4 kPa. The leakage current density obtained with positive bias is one order lower than that with negative bias in case of 29.4 kPa, which was one or two order higher than in case of 4.9 kPa. The high pressure condition was not suitable for the damascene process of BLT thin films due to the defects in electrical properties although the better efficiency of process. by higher removal rate of BLT thin films was obtained with the high pressure of 29.4 kPa in the previous study [2].

• 전자공학회논문지D
• /
• 제35D권5호
• /
• pp.33-39
• /
• 1998

The BST (Ba$_{1-x}$ Sr$_{x}$TiO$_{3}$)(50/50) thin film has been grown by RF magnetron reactive sputtering and its characteristics such as crystallization, surface roughness, and electrical properties have been investigated with varying the film thickness. The crystallization and surface roughness of BST thin film are investigated by using XRD and AFM, respectively The BST thin film anealed at 800.deg. C for 2 min has pure perovskite structure and good surface roughness of 16.1.angs.. We estimate that the thickness and dielectric constant of interface layer between BST film and electrode are 3nm and 18.9, respectively, by measuring the capacitance with various film thickness. As the film thickness increases form 80nm to 240nm, the dielectric constant at 10kHz increases from 199 to 265 and the leakage current density at 200kV/cm decreases from 0.682.mu.A/cm$^{2}$ to 0.181 .mu.A/cm$^{2}$. In the case of 240nm-thick BST thin film, the charge storage density and leakage current density at 5V are 50.5fC/.mu.m$^{2}$ and 0.182.mu.A/cm$^{2}$, respectively. The values indicate that the BST thin film is a very useful dielectric material for the DRAM capacitor.or.

• 한국재료학회지
• /
• 제7권9호
• /
• pp.811-823
• /
• 1997

차세대 반도체 배선분야에서, Cu박막은 현재의 AI을 대체할 물질로서 대두되고 있으며 CVD에 의한 선택적 증착은 Cu의 patterning과 관련하여 상당한 관심을 일으키고 있다. 본 연구에서는 (hfac)Cu(VTMS)의 유기원료를 사용하여, CVD공정변수, 운반기체, 표면 처리 공정에 따른 SiO$_{2}$, TiN, AI기판에 대한 선택성을조사하였다. 선택성은 저온(15$0^{\circ}C$), 저합(0.3Torr)에서 향상될 수 있었으며, 특히, HMDS in-situ-predosing공정에 의해 더욱 향상될 수 있었다. 모든 경우에 대해, H$_{2}$운반기체가 Ar 보다 짧은 incubation time과 높은 증착 속도가 얻어졌으며, Cu입자들의 크기가 작고 연결상태가 보다 양호하였다. 이는 H$_{2}$경우에 기판표면에 원료가 흡착되어 핵을 형성시키는 위치 (-OH)가 보다 많이 제공되기 때문으로 여겨진다. 이러한 미세구조의 차이는 H$_{2}$경우에 보다 낮은 비저항을 얻게 했다. HMDS in-situ predosing공정에 의한 Cu박막내 불순물 차이는 없었으며 뚜렷한 비저항의 차이도 나타나지 않았다.

• 전기화학회지
• /
• 제11권2호
• /
• pp.100-104
• /
• 2008

Titanium sheet metal substrates used in thin film batteries were wet etched and their surface area was increased in order to increase the discharge capacity and power density of the batteries. To obtain a homogeneous etching pattern, we used a conventional photolithographic process. Homogeneous hemisphere-shaped wells with a diameter of approximately $40\;{\mu}m$ were formed on the surface of the Ti substrate using a photo-etching process with a $20\;{\mu}m{\times}20\;{\mu}m$ square patterned photo mask. All-solid-state thin film cells composed of a Li/Lithium phosphorous oxynitride (Lipon)/$LiCoO_2$ system were fabricated onto the wet etched substrate using a physical vapor deposition method and their performances were compared with those of the cells on a bare substrate. It was found that the discharge capacity of the cells fabricated on wet etched Ti substrate increased by ca. 25% compared to that of the cell fabricated on bare one. High discharge rate was also able to be obtained through the reduction in the internal resistance. However, the cells fabricated on the wet etched substrate exhibited a higher degradation rate with charge-discharge cycling due to the nonuniform step coverage of the thin films, while the cells on the bare substrate demonstrated a good cycling performance.

• 전자공학회논문지D
• /
• 제34D권5호
• /
• pp.22-31
• /
• 1997

We have measured the optical properties, thickness, and energy band gap of the P $b_{1-x}$/100/L $a_{x}$100/ $Ti_{1-}$0.25x/100/ $O_{3}$ (PLT(x)) thin film prepared by the sol-gel method with varying the La concentration, x, fyom 15 nto 33 mol%. We have obtained the values from the tranmission spectrum and employed the envelope method in anayzing the spectrum. We have also performed the simulation of the transmission spectrum on the PC (personal computer) to verify the accuracy of the values 15 to 33mol%, the refractive index (at .lambda.=632.8nm) increases from 2.39 to 2.44. The extinction coefficient does not depend on the la concentration but mainly on te wavelength, and has the values between 0.2 and 0.5 at the wavelength shorter than 330nm and between 0.001 and 0.008 at the wavelength longer than 700nm. The energy band gap of the PLT (x) thin film has been obtained on the assumption of the direct band-to-band transition. It decreases from 3.28 to 3.17eV as the La concentration increases from 15 to 33 mol%. The thickness of the PLT(x) thin film has been also obtained in high accuracy by the envelope method..

• 한국재료학회지
• /
• 제16권10호
• /
• pp.606-613
• /
• 2006

This study was purposed to evaluate the influence of anodically oxidized film on titanium (Ti) onto MG-63 osteoblast-like cell attachment and activity. Only scratch lines created by polishing were seen in ASR and ANO-1 groups. About $1.5{\mu}m$-thick homogeneous oxide film which has pores of about $0.5{\mu}m$ diameter were formed in ANO-12. The crystalline structure of the oxide films formed by anodization in phosphoric acid electrolyte was $TiP_2O_7$. The total protein amounts of ANO-1 and ANO-12 groups showed higher values of maximum protein amount than that of AS-R group. At 3 days of incubation, total protein amount showed higher value in ANO-2 when comparing to that of AS-R (p<0.05). Based on the results of ALPase activity test, the degree of MG-63 cell differentiation for initial mineralization matrix formation was similar. For all the test groups after 1 day of incubation, MG-63 cells grew healthily in mono-layer with dendritic extensions. After incubation for 3 days, the specimen surfaces were covered more densely by cells, and numerous micro filaments were extruding to the extracellular matrix.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 춘계학술대회 논문집 전기설비전문위원
• /
• pp.27-29
• /
• 2009

본 연구에서는 Titanate Nanotube (TNT)를 LBL-SA (layer-by-layer self-assembling) method을 이용하여 전기변색 (electrochromism device, ECD) 소자에 적용하고자 하였다. TNT 분말은 10M NaOH와 $TiO_2$를 혼합한 후 autoclave에서 130$^{\circ}C$, 48시간 동안 수열합성하여 제조하였다. 주사전자현미경 (SEM)으로 TNT 분말의 형상을 관찰한 결과, 직경 20$\sim$30nm, 길이 500$\sim$600nm의 튜브 형상을 나타내었으며, X-선 회절시험 (XRD) 결과 층상구조로 확인되었다. 코팅 물질의 표면 전하를 이용한 LBL-SA method에 적용시키기 위해 수용액 중에서 TNT 입자 표면 전하를 TBAOH (tetrabutylammonium hydroxide)를 적정하여 제타 전위 값이 -40mV로 최대가 되도록 하였으며, 이때 pH 값은 9로 나타났다. 2전극 시스템을 이용하여 cycle voltammetry를 측정한 결과, -0.5$\sim$-1.5V 영역에서 산화환원전위 피크가 뚜렷하게 나타났으며, 짙은 갈색으로 변색되는 것을 확인하였다. 본 연구 결과로서 TNT 박막은 전기를 인가하였을 때 n-type 반도체 성질을 갖는 것으로 나타났으며, 앞으로 display 연구 분야에 적용할 수 있을 것으로 주목된다.

• 전자공학회논문지A
• /
• 제28A권10호
• /
• pp.840-846
• /
• 1991

In case of the rapid thermal process by halogen lamps, an optical pyrometer is generally used to measure the temperature. It is, however, necessary to measure the temperature by the thermocouple when the process temperature is lower than 700$^{\circ}C$ and the correction of the temperature is required. Contact by the PdAg paste is commonly used out but in this case it is impossible to see the effect of surface states of the substrate, which is critical in the rapid thermal process. In this study, real temperature ramping speed of silicon substrates coveredwith various thin films such as SiO$_2$2, Si$_{3}N_{4}$, dopants, and conductive layers (Ti or Co) was investigated by a mechanical contact of the thermocouple. And the results were compared with the case in which the contact was made by the PdAg paste. Effect of process ambient was also studied. It was found that depending on the surface state, overshoot more than 100$^{\circ}C$ could occur. It was also found that in case of the substrate covered with conductive layers, mechanical contact might render the correct temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.204-205
• /
• 2007

Self-seed 층을 이용한 PLZT(9/65/35), 강유전체 박막을 Sol-Gel 법을 이용해 Pt/Ti/$SiO_2$/Si 기판 위에 증착한 후, Self-seed 층에 의한 PLZT(9/65/35) 박막의 구조적, 전기적 특성을 고찰하였다. Seed 층을 도입하지 않은 PLZT 박막의 경우 다결정 상으로 형성되는 것을 알 수 있었으며, seed 층을 도입한 PLZT 박막은 (110) 방향으로 우선 배향됨을 알 수 있었다. 증착된 PLZT(9/65/35) 박막의 유전율 및 유전손살은 10kHz에서 유전율 205, 유전손살 0.029 이었으며, Self-seed layer를 도입한 PLZT 박막의 경우 seed layer를 도입하지 않은 PLZT 박막보다 낮은 온도에서 결정화 되는 것을 관찰 할 수 있었다. Self-seed layer가 도입된 PLZT(9/65/35) 박막의 경우 잔류분극 ($P_r$) 값은 $9.1{\mu}C/cm^2$, 항전계($E_c$)는 47 kV/cm을 나타내었다.