• 한국세라믹학회지
• /
• 제36권5호
• /
• pp.564-569
• /
• 1999

• 센서학회지
• /
• 제17권3호
• /
• pp.178-182
• /
• 2008

Planar type micro catalytic combustible gas sensor was developed by using nano crystalline $SnO_2$ Pt thin film as micro heater was deposited by thermal evaporation method on the alumina substrate. The thickness of the Pt heater was around 160 nm. The sensor showed high reliability with prominent selectivity against various gases(Co, $C_3H_8,\;CH_4$) at low operating temperature($156^{\circ}C$). The sensor with nano crystalline $SnO_2$ showed higher sensitivity than that without nano crystalline $SnO_2$. This can be explained by more active adsorption and oxidation of hydrogen by nano crystalline $SnO_2$ particles. The present planar-type catalytic combustible hydrogen sensor with nano crystalline $SnO_2$ is a good candidate for detection of hydrogen leaks.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.184-184
• /
• 2009

This paper introduces the characteristics of SnO2 inorganic film deposited by radio-frequency magnetron sputtering as an alternative alignment layer for liquid crystal display (LCD) applications. The pretilt angle of the SnO2 layer was shown to be a function of the ion beam(IB) incident angle, a planer alignment of nematic liquid crystal was achieved. The about $1.8^{\circ}$ of stable pretilt angle was achieved at the range from 1500 ~ 2500eV of incident energy. To characterize the film shows atomic force microscopy (AFM) on the IB irradiated SnO2 surfaceand the X-ray phtoelectron spectroscopy analysis showed that the liquid crystal(LC) alignment on the IB irradiated $SnO_2$ surface was due to the reformation of Sn-O bonds. Also, Figure 1 shows that The alignment capability of the IB irradiated SnO2 layers is maintained until annealing temperature of $200^{\circ}C$. Comparable electro-optical characteristics to rubbed polyimide were also achieved.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1998년도 추계학술발표강연 및 논문개요집
• /
• pp.82-82
• /
• 1998

• 한국재료학회지
• /
• 제18권2호
• /
• pp.69-72
• /
• 2008

A sensor element array for combinatorial solution deposition research was fabricated using LTCC (Low-temperature Co-fired Ceramics). The designed LTCC was co-fired at $800^{\circ}C$ for 1 hour after lamination at $70^{\circ}C$ under 3000 psi for 30 minutes. $SnO_2$ sol was prepared by a hydrothermal method at $200^{\circ}C$ for 3 hours. Tin chloride and ammonium carbonate were used as raw materials and the ammonia solution was added to a Teflon jar. 20 droplets of $SnO_2$ sol were deposited onto a LTCC sensor element and this was heat treated at $600^{\circ}C$ for 5 hours. The gas sensitivity ($S\;=\;R_a/R_g$) values of the $SnO_2$ sensor and 0.04 wt% Pd-added $SnO_2$ sensor were measured. The 0.04 wt% Pd-added $SnO_2$ sensor showed higher sensitivity (S = 8.1) compared to the $SnO_2$ sensor (S = 5.95) to 200 ppm $CH_3COCH_3$ at $400^{\circ}C$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.1276-1279
• /
• 2005

The long-term stability of pentacene thin-film transistors (TFTs) encapsulated with a transparent $SnO_2$ thin-film prepared by ion beam assisted deposition (IBAD) was investigated. With a buffer layer of thermally evaporated 100 nm $SnO_2$ film deposited prior to IBAD process, our encapsulated OTFTs sustained its initial field-effect mobility up to one month and then gradually degraded showing only 37% reduction compared to 90% reduction of non-encapsulated OTFTs after 100 days in air ambient. The encapsulated OTFTs also exhibited superior on/off current ratio of over $10^5$ to that of the unprotected devices $({\sim}10^4)$ which was reduced from ${\sim}10^6$ before aging. Therefore, the enhanced long-term stability of our encapsulated OTFTs should be attributed to well protection of permeation of $H_2O$ and $O_2$ into the devices by the IBAD $SnO_2$ thin-film which could be used as an effective inorganic gas barrier for transparent organic electronic devices.

• Journal of Korean Society for Atmospheric Environment
• /
• 제20권E2호
• /
• pp.69-75
• /
• 2004

In this study, thin film gas sensor based on tin oxide was fabricated to examine its characteristics. Target gas is acetonitrile ($CH_3$CN) which is a blood simulant for the chemical warfare agent. Sensing materials are SnO$_2$ SnO$_2$/Pt, and Sn/Pt with thickness from 1000 to 3000 $\AA$. The sensor consists of a sensing electrode with inter-digit (IDT) type in front side and a heater in rear side. Resistance changes of sensing materials are monitored on real time basis using a data acquisition board with a 12-bit analog to digital converter. Sensitivities are measured at different operating temperatures also with different gas concentrations and film thickness. The high sensitivity is obtained for Sn (3000 $\AA$)/Pt (30 $\AA$) at 30$0^{\circ}C$ for 3 ppm. Response and recovery times were about 40 and 160 s, respectively. Repetition measurements showed very good results with $\pm$3% in full scale range.

• 한국세라믹학회지
• /
• 제36권11호
• /
• pp.1156-1162
• /
• 1999

• Transactions on Electrical and Electronic Materials
• /
• 제10권4호
• /
• pp.135-139
• /
• 2009

$H_2S$ micro-gas sensors have been developed employing $SnO_2$:CuO composite thin films. The films were prepared by e-beam evaporation of Sn and Cu metals on silicon substrates, followed by oxidation at high temperatures. Results of various studies, such as scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) reveal that $SnO_2$ and CuO are mutually non-reactive. The CuO grains, which in turn reside in the inter-granular regions of $SnO_2$, inhibit grain growth of $SnO_2$ as well as forming a network of p-n junctions. The film showed more than a 90% relative resistance change when exposed to $H_2S$ gas at 1 ppm in air at an operating temperature of $350^{\circ}C$ and had a short response time of 8 sec.

• 한국전기전자재료학회논문지
• /
• 제17권12호
• /
• pp.1296-1300
• /
• 2004

SnO$_2$ is one of the most suitable gas sensor materials. The microstructure and surface morphology of films must be controlled because the electrical and optical properties of SnO$_2$ films depend on these characteristics. The effects of chemical mechanical polishing(CMP) on the variation of morphology of SnO$_2$ films prepared by RF sputtering system were investigated. The commercially developed ceria-based oxide slurry, silica-based oxide slurry, and alumina-based tungsten slurry were used as CMP slurry. Non-uniformities of all slurries met stability standards of less than 5 %. Silica slurry had the highest removal rate among three different slurries, sufficient thin film topographies and suitable root mean square(RMS) values.