• Journal of Sensor Science and Technology
• /
• v.6 no.5
• /
• pp.369-375
• /
• 1997

$V_{2}O_{5}/ThO_{2}/Pd$-doped $SnO_{2}$ sensor has a good selectivity and stability to CO at high sensor temperature of about $500^{\circ}C$, and shows rapid response. In particular, many kinds of interference gases, such as $NO_{x}$, $C_{3}H_{8}$, $CH_{4}$ and $SO_{2}$ have been found to give only a slight influence on the sensor selectivity to CO gas sensitivity by doped $V_{2}O_{5}$ (3.0 wt.%). For the sensor we used well-known thick film technological route with $V_{2}O_{5}$(3.0 wt.%), Pd(1.0 wt.%) and $ThO_{2}$(l.5 wt.%) as catalytic materials. In the case of mixed $NO_{x}$-CO gases, as combustion exhaust gas, only CO detection by $SnO_{2}$ type semiconductor sensor is generally very difficult because of $NO_{x}$ interference. The developed sensors can use to measure the exhausting gas of the automobile or the boiler for the Air-to-Fuel ratio control.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.12
• /
• pp.1296-1300
• /
• 2004

SnO$_2$ is one of the most suitable gas sensor materials. The microstructure and surface morphology of films must be controlled because the electrical and optical properties of SnO$_2$ films depend on these characteristics. The effects of chemical mechanical polishing(CMP) on the variation of morphology of SnO$_2$ films prepared by RF sputtering system were investigated. The commercially developed ceria-based oxide slurry, silica-based oxide slurry, and alumina-based tungsten slurry were used as CMP slurry. Non-uniformities of all slurries met stability standards of less than 5 %. Silica slurry had the highest removal rate among three different slurries, sufficient thin film topographies and suitable root mean square(RMS) values.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.2
• /
• pp.45-49
• /
• 1999

A flammable gas sensor based on the $SnO_2$thin film deposited by the reactive ion assisted deposition was fabricated and ultra-thin Pd layer as catalyst was adsorbed at surface by ion beam sputtering. The initial oxidation states of Pd catalyst were controlled to investigate the role of Pd in the sensing process of inflammale gas sensor through annealing in air and vacuum respectively. The Pd catalyst existing in pure metallic state showed the sensitivity higher than that of PdO. The result might be closely related to the fact that PdO as a surface acceptor would receive electrons via Pd sub-channel from $SnO_2$, and thus which reduces the sensitivity and delay the response time.

• Journal of Sensor Science and Technology
• /
• v.16 no.6
• /
• pp.428-433
• /
• 2007

$SnO_{2}$-based thick film ethanol gas sensors were fabricated on alumina substrates and their ethanol gas sensing characteristics were investigated. The film sintered at $400^{\circ}C$ for 2 hrs. showed the highest sensitivity to ethanol gas and the sensitivity of the film to 1000 ppm ethanol gas in air was 97 % at an operating temperature of $250^{\circ}C$. The addition of $Fe_{2}O_{3}$ to $SnO_{2}$ enhanced the sensitivity by changing the type and number of surface acidic/basic sites.

• Journal of Sensor Science and Technology
• /
• v.33 no.2
• /
• pp.105-111
• /
• 2024

In this study, the H₂S gas sensing characteristics were evaluated using surface-modified SnO₂ microparticles by tip sonication. The surface-modified SnO₂ microparticles were synthesized using the following sequential process. First, bare SnO₂ microparticles were synthesized via a hydrothermal method. Then, the surfaces of bare SnO₂ microparticles were modified with Ti nanoparticles during tip sonication. The sensing characteristics of SnO₂ microparticles modified with Ti were systematically investigated in the range of 100-300℃, compared with the bare SnO₂ microparticles. In this study, we discuss in detail the improved H₂S sensing characteristics of SnO₂ microparticles via Ti nanoparticle modification.

• Applied Chemistry for Engineering
• /
• v.18 no.2
• /
• pp.142-147
• /
• 2007

In this study, mesoporous tin oxide was synthesized by sol-gel method using $C_{16}TMABr$ surfactant as a template in a basic condition. The optimum conditions for the synthesis of mesoporous $SnO_2$ were investigated and the obtained samples were characterized by XRD, nitrogen adsorption and TEM analysis. A mesoporous and nanostructured $SnO_2$ gas sensor with Au electrode and Pt heater has been fabricated on alumina substrate as one unit via a screen printing process. Sensing abilities of fabricated sensors were examined for CO and $CH_4$ gases, respectively, at $350^{\circ}C$ in the concentration range of 1~10,000 ppm. Influence of loading amount of palladium impregnated on $SnO_2$ was also tested in detection of those gases. High sensitivity to detecting gases and the fast response speed with stability were obtained with the mesoporous tin oxide sensor as compared to a non-porous one under the same detection conditions.

• Journal of Sensor Science and Technology
• /
• v.30 no.6
• /
• pp.376-380
• /
• 2021

The accurate detection of hydrogen gas molecules is considered to be important for industrial safety. However, the selective detection of the gas using semiconductive metal oxides (SMOs)-based sensors is challenging. Here, we describe the fabrication of H₂ sensors in which a nanocellulose/graphene oxide (GO) hybrid membrane is attached to SnO₂ nanosheets (NSs). One-dimensional (1D) nanocellulose fibrils are attached to the surface of GO NSs (GONC membrane) by mixing GO and nanocellulose in a solution. The as-prepared GONC membrane is employed as a sacrificial template for SnO₂ NSs as well as a molecular sieving membrane for selective H₂ filtration. The combination of GONC membrane and SnO₂ NSs showed substantial selectivity to hydrogen gas (R_air / R_gas > 10 @ 0.8 % H₂, 100 ℃) with noise level responses to interfering gases (H₂S, CO, CH₃COCH₃, C₂H₅OH, and NO₂). These remarkable sensing results are attributed mainly to the molecular sieving effect of the GONC membrane. These results can facilitate the development of a highly selective H₂ detector using SMO sensors.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.4
• /
• pp.289-295
• /
• 2017

Detection of $CO_2$ gas in both indoor and outdoor atmospheres is now becoming an important issue because of greenhouse effect and climate crisis. In this study, gas sensors based on $SnO_2-Cr_2O_3$ composite nanofibers were fabricated by the electrospinning method to detect $CO_2$ gas. The gas sensors showed a response to ppm level of $CO_2$ gas from room temperature to $200^{\circ}C$ while the highest response was observed at $150^{\circ}C$. The gas response is enhanced by the catalytic property of $Cr_2O_3$. Selective $CO_2$ detection is obtained through the chemical reaction of $Cr_2O_3$ to chromium carbonate. All the results suggest the $SnO_2-Cr_2O_3$ composite material is promising for the use of $CO_2$ gas sensors.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1555-1557
• /
• 2004

The Pt-doped $SnO_2$ thin film for CO sensor applications obtained by RF sputtering from a target of the same compound in an Ar-$O_2$ atmosphere. Pt-SnO2-SiC Schottky diode detection of CO gas Cause the remarkable change in electrical resistivity of the semiconductor. the good gas sensitivity is shown when annealing condition is 600$^{\circ}C$, 1hr in RTP and detected temperature is 350$^{\circ}C$.

• Journal of Sensor Science and Technology
• /
• v.20 no.5
• /
• pp.289-293
• /
• 2011

Networked $SnO_2$ nanowires were uniformly functionalized with Pd nanoparticles via ${\gamma}$-ray radiolysis. The Networked $SnO_2$ nanowires were fabricated through a selective growth method. The sensing properties of the Pd-functionalized $SnO_2$ nanowires were analyzed in terms of their response to $NO_2$ and CO gases. The response time and sensitivity of the sensors were significantly improved for $NO_2$ at lower temperatures by the Pd functionalization. The enhancement in the sensing properties is likely to be due to the spillover effect of the Pd nanoparticles.