• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.2
• /
• pp.114-119
• /
• 2000

Etch characteristics of SF6/CI2 electron cyclotron resonance (ECR) plasmas have been investigated. Surface reaction of gas plasma with polysilicon was also analysed using X-ray photoelectron spectroscopy (XPS). At the same time, the relationship between surface reaction and the etched profile of polysilicon was examined using XPS. The etch rate of polysilicon and oxide increases with increasing flow rate of SF6 in the SF6/CI2 gas mixture, and tis selectivity also increase also increase. It was also found that as increasing flow rate of SF6 in the SF6/CI2 gas mixture, the atomic% of chlorine detected at surface region decrease, but F and S contents increase. At the same time, when the mixing ratio of SF6 gas increases, the anisotropy of etched polysilicon is sharply decreased in the 0%~10% range of the SF6 mixing ratio, but is rarely varied in the range over 10%, in spite of the large variations in flow rates. It can be explained that the bonding of S-Si due to SiSx(x$\leq$2) compound formed on the etched surface suppress the formation of Si-Cl and 'or Si-F bonding in the silicon etching.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.3
• /
• pp.63-67
• /
• 2001

Up to now, most studies about Pt-etching have been focused on physical sputtering mechanism with Cl-based plasma, while only a limited results are available for etching characteristics with fluorine-based plasma. In this study, etch characteristics of Pt thin film with $Cl_2$/Ar and $SF_{6}$/Ar Ar gas chemistries have been studied with ECR plasma etching system. It is confirmed that $SF_{6}$/Ar Ar plasma chemistry could make volatile etch-products through the reaction with Pt thin film. Also the improvement in etch rate, etch profile and surface roughness is obtained due to the formation of volatile platinum fluoride compounds.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2001.07a
• /
• pp.110-113
• /
• 2001

ECR(electron cyclotron resonance) 플라즈마 식각 장비를 이용하여 SF$_{6}$/Ar과 Cl$_2$/Ar 플라즈마 가스에 대한 Platinum (이하 Pt) 박막의 식각 특성을 연구하였다. Pt 박막의 경우 Cl$_2$ 가스 혼합물에 대한 식각 특성은 많이 보고가 되어 왔으나 상대적으로 Fluorine 계열의 가스 혼합물에 의한 시각 연구는 미비하였다. 본 연구에서는 SF$_{6}$/Ar과 Cl$_2$/Ar 플라즈마 가스를 이용한 Pt 박막의 식각 특성을 비교 분석하고 각각의 가스와 Pt 박막과의 반응을 분석, 식각 특성을 개선하고자 하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.3
• /
• pp.203-207
• /
• 1998

After etching Al-Cu alloy films using $SiCl_4/Cl_2/He/CHF_3$ plasma, a corrosion phenomenon on the metal surface has been studied with XPS (X-ray photoelectron spectroscopy) and SEM (Scanning electron microscopy). In Al-Cu alloy system, the corrosion occurs rapidly on the etched surface by residual chlorine atoms. To prevent the corrosion, the $SF_6$ plasma treatment subsequent to the etch has been carried out. A passivation layer is formed by fluorine-related compounds on etched Al-Cu alloy surface after $SF_6$ treatment, and the layer suppresses effectively the corrosion on the surface as the RF power of $SF_6$ treatment increases. The corrosion could be suppressed successfully with $SF_6$ treatment in the RF power of 150watts.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.3
• /
• pp.13-17
• /
• 2000

The electrical properties of polyimide for interlayer dielectric applications are investigated with ECR (Electron Cyclotron Resonance) etching process. ECR etching with $Cl_2$-based plasma, generally used for aluminum etching, results in an increase in the dielectric constant of polyimide, while $SF_{6}$ plasma exhibits a high polyimide etch rate and a reducing effect of the dielectric constant. The leakage current of the polyimide is significantly suppressed after plasma exposure. Combination of Al etching with $Cl_2$plasma and polyimide etching with $SF_{6}$ plasma is expected as a good tool for realizing the multilevel metallization structures.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.1
• /
• pp.6-12
• /
• 2000

In this study, molybdenum thin films were etched with Cl\ulcorner/(Cl\ulcorner+SF\ulcorner) gas mixing ratio in an magneti-cally enhanced reactive ion etching(MERIE) by the etching parameters such as rf power of 250 watts, chamber pressure of 100 mTorr and B-field of 30 gauss. The etch rate was 150nm/min under Cl\ulcorner/(Cl\ulcorner+SF\ulcorner) gas mixing ratio of 0.25. At this time, the selectivity of Mo to SiO\ulcorner, photoresist were respectively 0.94, 0.05. The surface reaction of the etched Mo thin films was investigated with X-ray photoelectron spectroscopy(XPS). It was analyzed that Mo peaks was mainly observed in Mo-O bonds formed MoO\ulcorner compounds and F was detected in Mo-F and O-F bonds. Cl peaks were detected by the peak of Cl 2p\ulcorner in Cl-Mo bonds of MoCl\ulcorner or MoO\ulcornerCl\ulcorner formulas. Almost all of both Cl and S atoms had been com-bined with Mo, respectively.

• ETRI Journal
• /
• v.21 no.3
• /
• pp.16-21
• /
• 1999

After etching Al-Cu alloy films using SiCl4/Cl_2/He/CHF3 mixed gas plasma, the corrosion phenomenon at the grain boundary of the etched surface and a passivation layer on the etched surface with an SF6 plasma treatment subsequent to the etching were studied. In Al-Cu alloy system, corrosion occurs rapidly on the etched surface by residual chlorine atoms, and it occurs dominantly at the grain boundaries rather than the crystalline surfaces. To prevent corrosion, the SF6 gas plasma treatment subsequent to etching was carried out. The passivation layer is composed of fluorine-related compounds on the etched Al-Cu surface after the SF6 treatment, and it suppresses effectively corrosion on the surface as the SF6 treatment pressure increases. Corrosion could be suppressed successfully with the SF6 treatment at a total pressure of 300 mTorr. To investigate the reason why corrosion could be suppressed with the SF6 treatment, behaviors of chlorine and fluorine were studied by various analysis techniques. It was also found that the residual chlorine incorporated at the grain boundary of the etched surface accelerated corrosion and could not be removed after the SF6 plasma treatment.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.4
• /
• pp.145-149
• /
• 2016

The effect of process parameters such as plasma composition, ICP (Inductively Coupled Plasma) source power and rf chuck power on the etch characteristics of GaN epitaxy layer was studied. $Cl_2/Ar$ ICP discharges showed higher etch rates than $SF_6/Ar$ discharges because of the higher volatility of $GaCl_x$ etch products than $GaF_x$ compounds. As the Ar ratio increases in the $Cl_2/Ar$ ICP discharges, the etch anisotropy was enhanced due to the improved physical component of the etching. For both plasma chemistries, the GaN etch rate increased continuously as both the ICP source power and rf chuck power increased, and a maximum etch rate of 251.9 nm/min was obtained at $13Cl_2/2Ar$, 750W ICP power, 400W rf chuck power and 10 mTorr condition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.34-38
• /
• 1999

In this study, molybdenum thin films were etched with the various Cl$_2$/(Cl$_2$+SF$_{6}$) gas mixing ratio in an magnetically enhanced reactive ion etching(MERIE) by the etching parameter such as rf power of 185 watts, chamber pressure of 40 mTorr and B-field of 80 gauss. The etch rate was 150 nm/min under Cl$_2$/(Cl$_2$+SF$_{6}$) gas mixing ratio of 0.25. At this time, the selectivity of Mo to SiO$_2$, photoresist were respectively 0.94, 0.50. The surface reaction of the etched Mo thin films was investigated with X - ray photoelectron spectroscopy (XPS).PS).

• Journal of the Korean Ceramic Society
• /
• v.40 no.9
• /
• pp.886-890
• /
• 2003

The etching characteristics of a LiNbO$_3$ single crystal have been investigated using helicon wave plasma source with bias power and the mixture of CF$_4$, HBr, SF$_{6}$ gas parameters. The etching rate of LiNbO$_3$ with etching parameters was evaluated by surface profiler. The etching surface was evaluated by Atomic Force Microscopy (AFM). The surface morphology of the etched LiNbO$_3$ changed with bias power and the mixture of CF$_4$/Ar/Cl$_2$, HBr/Ar/Cl$_2$, and SF$_{6}$/Ar/Cl$_2$ parameters. Optimum etching conditions, considering both the surface flatness and etch rate were determined.