• Journal of Sensor Science and Technology
• /
• v.5 no.5
• /
• pp.79-84
• /
• 1996

A $1\;{\mu}m$ thick n-type GaAs layer with Si doping density of $1{\times}10^{17}/cm^{3}$ and a $500{\AA}$ thick undoped single crystalline AlAs layer were subsequently grown by molecular beam epitaxy on the $n^{+}$ GaAs substrate. The AlAs/GaAs layer was oxidized in $N_{2}$ bubbled $H_{2}O$ vapor($95^{\circ}C$) ambient at $400^{\circ}C$ for 2 and 3 hours. From the result of XPS analysis, small amounts of $As_{2}O_{3}$, AlAs, and elemental As were found in the samples oxidized up to 2 hours. After 3 hours oxidation, however, various oxides related to As were dissolved and As atoms were diffused out toward the oxide surface. The as-grown AlAs/GaAs layer was selectively converted to $Al_{2}O_{3}/GaAs$ at the oxidation temperature $400^{\circ}C$ for 3 hours. The oxidation temperature and time is very critical to stop the oxidation at the AlAs/GaAs interface and to form a defect-free surface layer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.128.2-128.2
• /
• 2014

Long-wave infrared detectors using the type-II InAs/GaSb strained superlattice (T2SL) material system with the nBn structure were designed and fabricated. The band gap energy of the T2SL material was calculated as a function of the thickness of the InAs and GaSb layers by the Kronig-Penney model. Growth of the barrier material (Al0.2Ga0.8Sb) incorporated Te doping to reduce the dark current. The full width at half maximum (FWHM) of the 1st satellite superlattice peak from the X-ray diffraction was around 45 arc sec. The cutoff wavelength of the fabricated device was ${\sim}10.2{\mu}m$ (0.12eV) at 80 K while under an applied bias of -1.4V. The measured activation energy of the device was ~0.128 eV. The dark current density was shown to be $1.2{\times}10^{-5}A/cm^2$ at 80 K and with a bias -1.4 V. The responsivity was 1.9 A/W at $7.5{\mu}m$ at 80K and with a bias of -1.9V.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.1
• /
• pp.27-32
• /
• 2003

Highly reproducible side-wall process for the fabrication of the fine gate length as small as 40nm was developed. This process was utilized to fabricate 40nm InGaAs HEMTs with the 65% strained channel. With the usage of the dual $SiO_2$ and $SiN_x$ dielectric layers and the proper selection of the etching gas, the final gate length (Lg) was insensitive to the process conditions such as the dielectric over-etching time. From the microwave measurement up to 40GHz, extrapolated fT and fmax as high as 371 and 345 GHz were obtained, respectively. We believe that the developed side-wall process would be directly applicable to finer gate fabrication, if the initial line length is lessened below the l00nm range.

• Journal of the Korean Vacuum Society
• /
• v.4 no.S1
• /
• pp.168-173
• /
• 1995

$GaxIn{1_x}As$ epitaxial layers were grown by a simplified hydrode vapor phase epitaxy(VPE) method bsed on the utilization of Ga/In alloy as the source metal. The effects of a wide range of experimental variables(i.e.,inlet mole fraction of HCI, deposition temperature, Ga/In alloy composition) on the ternary composition and growth rate were investigated. Layers of $Ga_{0.47}In_{0.53}As$ lattice matched to InP were successfully grown from alloys containing 5 to 8 at.% Ga. These layers were used to produce state-of-the art p-i-n photodetectors having the following characteristics: dark current, $I_d$(-5V) = 10-20 nA: responsivity, R=0.84-0.86 A/W; dark current, Id(-5V)=10-20 nA; responsivity, R=0.84-0.86 A/W; capacitance, C=0.88-0.92 pF; breakdown voltage, $V_b$ >40V. This study demonstrated for the first time that a simplified hydride VPE process with a Ga/In alloy source is capable of producing device quality epitaxial layers.

• Journal of Sensor Science and Technology
• /
• v.32 no.6
• /
• pp.425-431
• /
• 2023

An asymmetric metal-semiconductor-metal Al_0.24Ga_0.76N ultraviolet (UV) sensor was fabricated, and the effects of local Joule heating were investigated. After dielectric breakdown, the current density under a reverse bias of 2.0 V was 1.1×10^-9 A/cm², significantly lower than 1.2×10^-8 A/cm² before dielectric breakdown; moreover, the Schottky behavior of the Ti/Al/Ni/Au electrode changed to ohmic behavior under forward bias. The UV-to-visible rejection ratio (UVRR) under a reverse bias of 7.0 V before dielectric breakdown was 87; however, this UVRR significantly increased to 578, in addition to providing highly reliable responsivity. Transmission electron microscopy revealed interdiffusion between adjacent layers, with nitrogen vacancies possibly formed owing to local Joule heating at the AlGaN/Ti/Al/Ni/Au interfaces. X-ray photoelectron microscopy results revealed decreases in the peak intensities of the O 1s binding energies associated with the Ga-O bond and OH-, which act as electron-trapping states on the AlGaN surface. The reduction in dark current owing to the proposed local heating method is expected to increase the sensing performance of UV optoelectronic integrated devices, such as active-pixel UV image sensors.

• Journal of Magnetics
• /
• v.17 no.1
• /
• pp.13-18
• /
• 2012

Starting with Kubo's formula and using the projection operator technique introduced by Kawabata, EPR lineprofile function for a $Mn^{2+}$-doped wurtzite structure GaN semiconductor was derived as a function of temperature at a frequency of 9.49 GHz (X-band) in the presence of external electromagnetic field. The line-width is barely affected in the low-temperature region because there is no correlation between the resonance fields and the distribution function. At higher temperature the line-width increases with increasing temperature due to the interaction of electrons with acoustic phonons. Thus, the present technique is considered to be more convenient to explain the resonant system as in the case of other optical transition systems.

• Current Photovoltaic Research
• /
• v.4 no.3
• /
• pp.108-113
• /
• 2016

III-V compound semiconductor based thin film solar cells promise relatively higher power conversion efficiencies and better device reliability. In general, the thin film III-V solar cells are fabricated by an epitaxial lift-off process, which requires an $Al_xGa_{1-x}As$ ($x{\geq}0.8$) sacrificial layer and an inverted solar cell structure. However, the device performance of the inversely grown solar cell could be degraded due to the different internal diffusion conditions. In this study, InGaP/GaAs double-junction solar cells are inversely grown by MOCVD on GaAs (100) substrates. The thickness of the GaAs base layer is reduced to minimize the thermal budget during the growth. A wide band gap p-AlGaAs/n-InGaP tunnel junction structure is employed to connect the two subcells with minimal electrical loss. The solar cell structures are transferred on to thin metal films formed by Au electroplating. An AlAs layer with a thickness of 20 nm is used as a sacrificial layer, which is removed by a HF:Acetone (1:1) solution during the epitaxial lift-off process. As a result, the flexible InGaP/GaAs solar cell was fabricated successfully with an efficiency of 27.79% under AM1.5G illumination. The efficiency was kept at almost the same value after bending tests of 1,000 cycles with a radius of curvature of 10 mm.

• Korean Journal of Optics and Photonics
• /
• v.12 no.1
• /
• pp.40-47
• /
• 2001

The structural dependence of the performance of an 1.55 $1.55{\mu}m$ InGaAsPIInGaAsP MQW electro-absorption modulator for highspeed digital fiber communication was systematically investigated. The effects of n-doped SCH region length $t_n$ as well as the general structure parameters including quantum well number $N_w$, well-thickness $t_w$, detuning wavelength $\Delta\lambda$, and device length L were thoroughly analyzed. Thereby, a high-pelfoIDlance electro-absorption modulator with device length L of $100{\mu}m$ was successfully designed. The designed structure showed excellent characteristics that have residual loss less than -1.5 dB, operational voltage from 0 V to -2V, and extinction ratios of -2.92 dB at $V_{\alpha}$=-1 V and -10 dB at $V_{\alpha}$=-2V.X>=-2V.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.154-154
• /
• 2003

A stoichiometric mixture of evaporating materials for CuGaSe2 single crystal thin films was prepared from horizontal electric furnace. Using extrapolation method of X-ray diffraction patterns for the polycrystal CuGaSe2, it was found tetragonal structure whose lattice constant at and co were 5.615 ${\AA}$ and 11.025 ${\AA}$, respectively. To obtain the single crystal thin films, CuGaSe2 mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the hot wall epitaxy (MWE) system. The source and substrate temperatures were Slot and 450$^{\circ}C$, respectively. The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (UXD). The carrier density and mobility of CuGaSe2 single crystal thin films measured with Hall effect by van der Pauw method are 5.0l${\times}$10$\^$17/ cm$\^$-3/ and 245 $\textrm{cm}^2$/V$.$s at 293K, respectively. The temperature dependence of the energy band gap of the CuGaSe2 obtained from the absorption spectra was well described by the Varshni's relation, Eg(T) = 1.7998 eV - (8.7489${\times}$10$\^$-4/ eV/K)T$^2$/(T + 335 K. After the as-grown CuGaSe2 single crystal thin films was annealed in Cu-, Se-, and Ca-atmospheres, the origin of point defects of CuGaSe2 single crystal thin films has been investigated by the photoluminescence(PL) at 10 K The native defects of V$\_$CU/, V$\_$Se/, Cu$\_$int/, and Se$\_$int/ obtained by PL measurements were classified as a donors or accepters type. And we concluded that the heat-treatment in the Cu-atmosphere converted CuGaSe2 single crystal thin films to an optical n-type. Also, we confirmed that Ga in CuGaSe2/GaAs did not form the native defects because Ga in CuGaSe2 single crystal thin films existed in the form of stable bonds.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.3
• /
• pp.107-112
• /
• 2010

The Cu$(In_{1-x}Ga_x)Se_2$ is the absorber material for thin film solar cell with high absorption coefficient of $1{\times}10^5cm^{-1}$. In the case of CIGS, the movable energy band gap from $CuInSe_2$ (1.00 eV) to $CuGaSe_2$ (1.68 eV) can be acquired while controlling Ga contain ratio. Generally, the co-evaporator method have used for development and fabrication of the CIGS absorption layer. However, this method should need many steps and lengthy deposition time with high temperature. For these reasons, in this paper, a new growth method of CIGS layer was attempted to hydride vapor transport (HVT) method. The CIGS mixed-source material reacted for HCl gas in the source zone was deposited on the substrate after transporting to growth zone. c-plane $Al_2O_3$ and undoped GaN were used as substrates for growth. The characteristics of grown samples were measured from SEM and EDS.