• Journal of Fisheries and Marine Sciences Education
• /
• v.11 no.2
• /
• pp.139-149
• /
• 1999

Thermal sprayed Ni-Cr alloy coating on the carbon steel was carried out erosion-corrosion test and electrochemical corrosion test in the marine environment. The erosion-corrosion behavior and electrochemical corrosion characteristics of substrate(SS400) and thermal sprayed Ni-Cr coating was investigated. The erosion-corrosion control efficiency of Ni-Cr coating to substrate was also estimated quantitatively. The main results obtained are as follows : 1) The weight loss rate of Ni-Cr coating layer by the erosion-corrosion compared with substrate was smaller. With the lapse of time, the weight loss rate of substrate was linearly increased in $25{\Omega}{\cdot}cm$ solution, but that of Ni-Cr coating became stable. 2) The corrosion potential of substrate became less noble than that of Ni-Cr coating layer, and the corrosion current density of Ni-Cr coating became lower than that of substrate. 3) The control efficiency of erosion-corrosion of Ni-Cr coating compared to substrate became more dull than that of corrosion in $25{\Omega}{\cdot}cm$ and $5000{\Omega}{\cdot}cm$ solution.

• Journal of Sensor Science and Technology
• /
• v.6 no.1
• /
• pp.43-48
• /
• 1997

$Ca_{10}(PO_{4})_{6}(OH)_{2}$ humidity-sensitive devices were fabricated by a solid reaction method, and their humidity-sensitive characteristics were investigated. The impedance decreases with increasing relative humidity, and the good sensitivity is shown in which impedance changes by about $10^{2}\;{\Omega}$ over the region of $30{\sim}90\;%$. Also, It is shown that the humidity sensitivity is stable in temperature variations and long time exposures to the humidity. The sensitivity of the specimens is not affected by a heat treatment, and the hysteresis in one humidity cycle is negligible.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04a
• /
• pp.7-10
• /
• 2002

We designed the flyback planar transformer, which had 8W capacity, with 70V input voltage and 8.2V output voltage for the establishment of design method and the confirmation of application possibility. The numerical value of inductance measured under the switching frequency of 120 kHz was 1650 ${\mu}H$, which was the inductance efficiency of 85~87% against theoretical value. The A.C. resistance of primary and secondary coil was 4.2 ${\Omega}$ and 0.25 ${\Omega}$ respectively. On the other hand, the quality factor for each wound numbers showed quite a high value of 158 and 75 respectively. And the Coupling Factor was 0.96~0.97 under 120 kHz switching frequency. And the shape of the output wave of the planar transformer at 70V input voltage was a stable square wave.

• Journal of Korean Society on Water Environment
• /
• v.29 no.6
• /
• pp.808-812
• /
• 2013

A new type of microbial fuel cell (MFC) with anaerobic membrane filter was designed to produce bioelectricity and to treat domestic sewage at relatively high organic loading rate (OLR) of $6.25kgCOD/m^3/day$ and short hydraulic retention time (HRT) of 1.9 h. A following aeration system was applied to ensure effluent water quality in continuous operation. Glucose was supplemented to increase the influent concentration of domestic sewage. Influent substrate of 95% was removed via the MFC and following aeration system and the corresponding maximum power density was $25.6mW/m^3$. External resistor of $200{\Omega}$ and air-cathode system contributed better MFC performance comparing to $2000{\Omega}$ and dissolved oxygen as a catholyte.

• Journal of Life Science
• /
• v.28 no.8
• /
• pp.945-954
• /
• 2018

Omega-3 polyunsaturated fatty acids (${\omega}3$-fatty acid) have been found to possess anticancer properties in a variety of cancer cell lines and animal models, but their effects in human tongue squamous cell carcinomas (SCCs) remain unclear. This study was designed to examine the effect of ${\omega}3$-fatty acid desaturase (fat-1) gene expression on invasion and tumorigenicity in human tongue SCC cells and the molecular mechanism of its action. Docosahexaenoic acid (DHA) treatment inhibited in vitro invasion in a dose-dependent manner. In zymography, matrix metalloproteinase-9 (MMP-9) and Matrix metallopeptidase-2 (MMP-2) activities were reduced, and MMP-9 and MMP-2 promoter activities were inhibited by the DHA treatment. In addition, cyclooxygenase-2 (COX-2) and vascular endothelial growth factor (VEGF) promoter reporter activities were inhibited in SCC-4 and SCC-9 cells after the DHA treatment. To investigate the effect of a high level of endogenous ${\omega}3$ fatty acids, a stable SCC-9 cell line expressing the ${\omega}3$-desaturase gene (fSCC-9sc) was generated. The growth rate and colony-forming capacity of fSCC-9sc were remarkably decreased as compared with those of fSCC-9cc. Likewise, the tumor size and volume of fSCC-9sc implanted into nude mice were significantly inhibited, with increases in the cell death index. Furthermore, a transwell chamber invasion assay showed a reduction in cell invasion of the fSCC-9sc lines when compared with that of the fSCC-9cc line. These findings suggested that fat-1 gene expression inhibited tumorigenicity, as well as invasion in human tongue SCC cells. Thus, utilization of ${\omega}3$ fatty acids may represent a promising therapeutic approach for chemoprevention and the treatment of human tongue SCCs.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.2
• /
• pp.272-277
• /
• 2008

Symmerge is a stable minimum storage merging algorithm that needs $O(m{\log}{\frac{n}{m}})$ element comparisons, where in and n are the sizes of the input sequences with $m{\leq}n$. Hence, according to the lower bound for merging, the algorithm is asymptotically optimal regarding the number of comparisons. The Symmerge algorithm is based on the standard recursive technique of "divide and conquer". The objective of this paper is to consider the relationship between m and n for the degenerated case where the recursion depth reaches m-1.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.4
• /
• pp.2343-2348
• /
• 2014

Main ground net of power plant is formed to protect human body from increase in potential gradient caused by grounding current during ground fault. Calculations during ground design are generally performed according to IEEE Std-80-2000 (Kepco Design Standard 2602). However, it is difficult to apply this Standard to water environment, and a grounding technology is required to secure grounding resistance of floating photovoltaic system. Therefore the aim of this paper is to investigate and analyze ground resistivity on the water surface and underwater of reservoir using Wenner 4-pin method, a general method of measuring ground resistivity. Also, grounding resistance of floating photovoltaic systems currently in operation was measured and analyzed using the voltage drop method suggested in the international standard (IEEE Std-81) to propose a grounding method for stable grounding of floating photovoltaic system. The resistivity at 1m below the surface of water ($126.3969[{\Omega}{\cdot}m]$) is mostly higher than resistivity at the river bed ($97.5713[{\Omega}{\cdot}m]$). Also the proposed grounding anchor method was determined as the most effective method of securing stable grounding resistance in floating photovoltaic systems and is expected to be utilized as a ground method for future floating photovoltaic generation systems.

• Korean Journal of Food Science and Technology
• /
• v.30 no.5
• /
• pp.1114-1119
• /
• 1998

The stabilities of O/W emulsions (lipophilic core material:lipophobic wall material=3:2, w/w) containing various kinds of emulsifiers were compared to determine the optimal conditions of the HLB (hydrophilic lipophilic balance) value, the concentration and composition of emulsifier, the ratio of core material to the wall material, and the concentration and composition of polymers in the wall material. The effect of different chemical types of emulsifiers and the influence of single vs. binary emulsifier systems were compared with 13 kinds of emulsifier HLB values of $0.6{\sim}16.7$ at the concentration of 0.50%(w/w). The emulsion system was stable (more than 99.0 of ESI value) when the HLB value of the emulsifier was more than 11.0 or less than 2.8 of emulsifier HLB value. But it was unstable (less than 40.0 of ESI value) at the HLB value of the emulsifier between 3.4 and 8.6. Especially, we could find out the emulsion containing the emulsifier of polyglycerol polyricinoleate (PGPR, HLB 0.6) became stable creamy state. And, the ESI value of binary emulsifier system containing 0.25%(w/w) of PGPR and 0.25%(w/w) of polyoxyethylene sorbitan monolaurate (PSML, HLB 16.7) was higher than that of any single emulsifier system at the concentration of 0.50%(w/w). The highest emulsion stability was obtained in the liquefied wall material composed of 0.25%(w/v) of waxy corn starch and 0.50%(w/v) of agar.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.3
• /
• pp.195-202
• /
• 1998

The LPCVD system of batch type for the massproduction of semiconductor fabrication has a problem of phosphorous concentration uniformity in the boat. In this paper we study an improvement of the uniformity for phosphorous concentration and sheet resistance. These property was improved by using the nitrogen process and modified long nozzle for gas injection tube in the doped polysilicon deposition system. The phosphorous concentration and its uniformity for polysilicon film are measured by XRF(X-ray Fluorescence) for the conventional process condition and nitrogen process. In conventional process condition, the phosphorous concentration, it uniformity and sheet resistance for polysilicon film are in the range of 3.8~5.4$\times$10\ulcorner atoms/㎤, 17.3% and 59~$\Omega$/ , respectively. For the case of nitrogen process the corresponding measurements exhibited between 4.3~5.3$\times$10\ulcorner atoms/㎤, 10.6% and 58~81$\Omega$/ . We find that in the nitrogen process the uniformity of phosphorous concentration improved compared with conventional process condition, however, the sheet resistance in the up zone of the boat increased about 12 $\Omega$/ . In modified long nozzle, the phosphorous concentration, its uniformity and sheet resistance for polysilicon films are in the range of 4.5~5.1$\times$10\ulcorner atoms/㎤, 5.3% and 60~65$\Omega$/ respectively. Annealing after $N_2$process gives the increment of grain size and the decrement of roughness. Modification of nozzle gives the increment of injection amount of PH$_3$. Both of these suggestion result in the stable phosphorous concentration and sheet resistance. The results obtained in this study are also applicable to process control of batch type system for memory device fabrication.

• Journal of the Korean Society of Safety
• /
• v.31 no.6
• /
• pp.25-31
• /
• 2016

This paper has analyzed the structure, applicable regulations and the resistance characteristics of insulation ring type of CSST (Corrugated Stainless Steel Tubing for Gas). With the flammability test conducted in accordance with KS C IEC 60811-1-1, the evaluation of insulation resistance, temperature characteristics, and reliability has been conducted. An insulation ring type CSST consists of protective coating, tube, nut, insulation ring, packing, socket, and ball valve. Connecting an insulation ring type CSST to gas tubings for gas appliance is not permitted, moreover, the product shall be installed inside a sleeve pipe in case of buried installation such as the ceiling. Damages on protective coating and tube were detected when fire was applied to the test sample with a portable torch for 60 seconds. The insulation resistance of a normal product was $49.59M{\Omega}$, while that of the product completed the flammability test reduced to $9.21M{\Omega}$. The mean insulation resistance within the confidence Interval of 95% using the mini tap program 17 was $49.59M{\Omega}$ and the mean insulation resistance within the confidence interval reduced to $9.21M{\Omega}$. In the normal distribution analysis of 95% confidence interval, the value-P of the normal product was stable at 0.075 and AD(Anderson-Darling) statistic value was turned out to be 0.063, which is very normal, and the standard deviation was analyzed as 0.2586. The value P of the product completed the flammability test resulted in 0.005, the AD was 1.355 and the standard deviation reduced to 0.07908.