Members of the NZOHS attended the Korean Society of Occupational Health Conference held in Korea last February of 2023, and have continued to attend before that. In response to their invitation, I share the story of attending the NZOHS Conference held once every two years as part of international exchange, one of the goals of the current 17th executive team.

Objectives: With the evolution of direct reading sensors, it is possible to monitor several substances through telecommunication. However, there are some limitations on the use of direct reading technologies in the Occupational Safety and Health Act in South Korea, which only applies to detector tubes, noise, heat, and carbon monoxides. The number of chemicals and their amount of use have been continuously increasing in South Korea. The Ministry of Employment and Labor (MoEL) has concerns about worker's health because exposure is only covered for about 1.2% of all distributed chemicals. Using a direct reading monitor with photoionization detectors (PID-DRMs), gases and vapors chemicals can be measured. Based on the data, business owners are able to create corrective strategies, provide better working routines, and select correct respiratory equipment. PID-DRMs are less expensive and easier to handle for an owner voluntarily controlling chemicals emitted in the workplace. However, there are several limitations on using these PID-DRMs to the degree that the MoEL has not been able to select a legal monitor. The aim of this study was to review previous studies related to PID-DRMs and identify the characterization and limitation on PID-DRMs. Methods: To search for related studies on PID-DRMs, key words were used including direct reading monitors/instruments and/or photoionization detectors. Through that, four domestic and 15 international studies were reviewed. Results: Studies on PID-DRMs were conducted by chamber (enclosed, dynamic, walk-in) and in the field (experimental environment, actual environment). The concentration of PID-DRMs and charcoal tubes were compared for a single substance or mixture, or within the PID-DRMs. There was a high correlation between the two concentrations, but it did not meet the accuracy criteria (95% confidence interval, within 25%) of the NIOSH technical report (2012). In addition, differences in measured values occurred according to environmental factors (temperature, humidity) and high concentration, and concentration values tended to be underestimated due to contamination of the sensor. As a way to improve the accuracy of PID concentration, it was proposed to use correction factors, charcoal tube-based correction factors, or to calibrate the PID-DRMs in the same environment as the workplace. Conclusions: PID-DRMs can likely be used by business owners for the purpose of voluntarily managing the workplace environment, and it is expected that it will be possible to use them as legal equipment if a PID sensor can be upgraded and the limitations of the sensor (temperature, humidity, high concentration evaluation, sensor pollution) can be overcome in the near future.

Objectives: This study was conducted to evaluate hand-arm vibration (HAV) exposure levels due to the use of power hand tools and to evaluate the determinants in the automobile assembly process. Methods: The exposure level to HAV was evaluated for 30 work lines in five assembly processes (body, engine, chassis, door, and design) that use air-powered tools and battery-powered tools and operate in circulation for two hours. The 2-hr equivalent energy vibration acceleration, A (2), of the task was measured. The 8-hr equivalent energy vibration acceleration, A (8), was estimated in consideration of the number of tasks that can be performed per day by each process. In addition, a survey on the working environment was conducted with workers exposed to vibration. Results: The geometric mean of the HAV exposure level, A (2), for a total of 30 tasks was 2.51 m/s², and one case was 10.30 m/s², exceeding TLV (2hr). The HAV exposure level of A (8) was evaluated from 1.03 m/s² to 5.36 m/s². A (2) showed a statistically significant difference (P<0.01) for each process, and the chassis process (GM=3.90 m/s²) was the highest. The larger the tool size and the longer the tool length, the higher was the vibration acceleration when using a battery-powered tool than an air-powered tool (P<0.01). Battery-powered tool users showed higher dissatisfaction on all items than did air-powered tool users. Conclusions: As a result of this study, it is necessary to implement a program to reduce the HAV exposure levels.

Objectives: This study was conducted to measure the level of radon in the air at a highway tunnel construction site in a gneiss area using the New Austrian Tunneling Method (NATM) and to evaluate exposure levels by occupation. Methods: Radon concentrations in the air were measured using E-PERM at points 300 m, 600 m, and 900 m from the tunnel entrance during the excavation and waterproofing work inside the tunnel. In addition, radon concentrations were measured during external excavation to compare with the inside of the tunnel. Personal exposure levels for major occupations including tunnel workers, construction equipment operators, waterproofers, shotcrete workers, and safety and health managers who participated in the construction were estimated using radon concentration measured in the work process area and working hours by occupation. Results: As a result of a total of 77 radon measurements, the geometric mean (GM) concentration was 71.1 Bq/m³, and the maximum concentration was 127.3 Bq/m³, which was below the indoor air quality criteria. Radon concentration by process decreased in the order of the tunnel excavation process (GM= Bq/m³, GSD=1.2), waterproofing process (GM=73.35 Bq/m³, GSD=1.2), and outside excavating process (GM=45.28 Bq/m³, GSD=1.2). Processes inside the tunnel were significantly higher than outside excavating processes (p<0.05). There was no statistically significant difference in radon concentration measured inside by distance from the tunnel entrance, but the innermost point of the tunnel, 900 m (GM=79.24 Bq/m³, GSD=1.27), measured the highest. Conclusions: The occupation with the highest individual exposure to radon was tunnel worker (64.16 Bq/m³), followed by construction equipment driver (64.04 Bq/m³) and waterproofer (63.13 Bq/m³).

Objectives: This study was conducted to find out the prevalence and risk factors of anemia according to shift work. Methods: Data from the Korean National Health and Nutrition Survey (2016-2020) were used. 9,787 workers were divided into shift workers and non-shift workers. The work type between 6AM-6PM was defined as day work, and other work types were defined as shift work. A chi-square test was used to indicate the distribution of risk factors expected to affect shift work in both frequency and percentage. Multiple logistic regression analysis was performed to find out the relationship between anemia prevalence and shift work. Results: As a result of analysis, multiple logistic regression analysis of anemia prevalence and shift work, the OR (95% CI) of male workers on shift work was 2.186 (1.139 to 4.194) and there was a statistically significant difference. Conclusions: In conclusion, anemia in male shift workers should be considered a possibility of health problems. In the future, research based on various data collection should be conducted for research to reveal various causes or diseases of anemia in the future.

Objectives: Active pulmonary tuberculosis (active PTB) is manifested in one of the complications of pneumoconiosis, but statistics are not available. The objective of the present study was to identify the incidence of active PTB among dusty workers who were diagnosed with pneumoconiosis by year. Methods: The present study was performed using the results of the Pneumoconiosis Examination Council's assessment from the Korea Workers' Compensation and Welfare Service (KCOMWEL) database between January 1, 1984, and December 31, 2017. Pneumoconiosis is defined as Category 1 or more. Active PTB was defined as a positive result for active PTB in the result of the Pneumoconiosis Examination Council's assessment. The annual incidence rate of pneumoconiosis and active PTB were analyzed by age standardization. Results: The number of retired dusty workers who received the health examination for work-related pneumoconiosis increased every year. However, the incidence of pneumoconiosis among retired dusty workers and active PTB among patients with pneumoconiosis decreased every year. Conclusions: To effectively manage pneumoconiosis and active PTB among patients with pneumoconiosis, the annual status of them in retired dusty workers who received the health examination for work-related pneumoconiosis was required.

Objectives: A fit test panel is needed to identify the fit performance of a respirator and its face seal. This is a criterion for selecting subjects that can represent the facial characteristics of users. Although anthropometry data has been developed for people in United States and China it is not yet present in Korea. This study aimed to develop a Korean fit test panel and test headform. Methods: For the 7th and 8th waves of the Size Korea anthropometry data, facial measurements of 11,429 people aged 15 to 69 years were used for analysis. PCA and bivariate panel were classified using the ISO16976-2:2022(E) anthropometrics analysis method. Based on this result, a static headform was developemed and a fit test chamber was constructed. Results: Of the 11,429 Korean people used for principal component analysis, 11,300 were included in the ellipse, marking an acceptance rate of 98.87% on PCA panel. The face types were classified into five types. Among them, a large, medium, and small static headform were printed using a 3D printer. In addition, 10,985 people (96.12%) were included in the bivariate panel based on face length and face width. The y-axis (face length) boundary was 97.87 to 134.59 mm, and the x-axis (face width) boundary was 120.75 to 158.23 mm. Conclusions: Compared to the ISO analysis, the Korean principal component was narrower in the width item (PC1) and longer in the length item (PC2). For the future, it is necessary to conduct a fit test using the developed headform and chamber device to confirm the usefulness of this Korean test panel. Therefore, this study is considered valuable as basic research for Korean test panels.

Objectives: This study conducted practical training to improve the proper usage of personal protective equipment(PPE), which greatly impacts workplace safety and health management. Personal protective equipment education was conducted through active participation, without theoretical modules, and aimed to identify the effects of repeated practical education and determine ways to increase participant satisfaction. Methods: Study data were analyzed using the IBM SPSS Statistics ver.29 software. First, participants' general characteristics were analyzed with frequency analysis. Second, the normality and equality of variances (Leven's test) were tested for the dependent variables prior to statistical analyses to determine the use of parametric tests. In general, normality is assumed when the sample size is 30 or more per the central limit theorem (Park et al., 2014). As our sample size of health management workers was 43, normality can be assumed. However, to ensure rigor of the study, we examined skewness and kurtosis. The results confirmed that the data were normally distributed. Third, the effects of repeated PPE training were analyzed using paired t-tests. Fourth, differences in satisfaction with PPE training according to the safety and health job position and safety and health certification were analyzed with t-test and Welch's t-test. For parameters that did not meet the assumption of equal variances, the Welch's t-test was performed. Results: Repeated PPE training improved the educational outcomes, and the improvements were significant in the 1st and 2nd respiratory PPE and safety and hygiene PPE training evaluations (p<.001). In terms of safety and health job position, repeated training led to improvements in educational outcomes, with significant improvements observed among supervisors and specialized health management institution workers in the 1st and 2nd training evaluations (p<.005). In terms of safety certification, repeated training led to improvements in educational outcomes, with significant improvements observed among both certified and non-certified individuals (p<.005). Regarding satisfaction with PPE training according to safety and health job positions, specialized health management institution workers showed greater satisfaction than supervisors, with significant differences in the satisfaction for expertise of lecture, work relevance, and lecturer's attitude (p<.001). Regarding satisfaction with PPE training according to safety and health certification, satisfaction was higher among certified individuals, with significant differences in satisfaction for work relevance and lecture attitude (p<.05) Conclusions: PPE education should be recommended to be provided as practical training. Repeated training can enhance educational outcomes for individuals with inadequate knowledge and understanding of PPE prior to education. For individuals with high levels of pre-existing knowledge and understanding of PPE, the results show that various training experiences should be provided to enhance their satisfaction. Therefore, it suggests that the workplace should actively seek educational media and methods to acquire expertise and skills in wearing personal protective equipment and improve the ability to use

Objectives: Aircraft cabin cleaning work is characterized by being performed within a limited time in a narrow and enclosed space. The objective of this study was to evaluate the exposure levels to dust, ultra fine dust(PM2.5) and black carbon(BC) among aircraft cabin cleaners. Methods: Active personal air sampling for respirable dust(n=73) and BC(n=47) was conducted during quick transit cleaning(cabin general and vacuum-specific) and seat cover replacement and total dust and PM2.5 were area-air-sampled as well. Also, size distribution of particle was identified with the cleaning workers targeted. Dusts were collected with PVC filters using gravimetric analysis. The concentration of PM2.5 and the particle size distribution were measured with real-time direct reading portable equipment using light scattering analysis. The concentration of BC was measured by aethalometer(filter-based real-time light absorption analysis instrument). Results: The geometric mean of respirable dust was the highest at vacuum cleaning as 74.4 ㎍/m³, following by replacing seat covers as 49.3 ㎍/m³ and cabin general cleaning as 47.8 ㎍/m³ . The arithmetic mean of PM2.5 was 4.83 ~ 9.89 ㎍/m³ inside the cabin, and 28.5~44.5 ㎍/m³ outside the cabin(from bus and outdoor waiting space). From size distribution, PM_2.5/PM₁₀ ratio was 0.54 at quick transit cleaning and 0.41 at replacing seat covers. The average concentration of BC was 2~7 ㎍/m³, showing a high correlation with the PM2.5 concentration. Conclusions: The hazards concentration levels of aircraft cabin cleaners were very similar to those of roadside outdoor workers. As the main source of pollution is estimated to be diesel vehicles operating at airports, and it is necessary to replace older vehicles, strengthen pollutant emission control regulations, and introduce electric vehicles. In addition, it is necessary to provide as part of airport-inftastructure a stable standby waiting space for aircraft cabin cleaners and introduce a systematic safety and health management system for all workers in the aviation industry.

Objectives: Methanol poisoning accidents in smartphone parts manufacturing facilities were analyzed using a systemic accident analysis method, and the necessity and possibility of the application of this systemic method in the field of occupational health were reviewed. Methods: A STAMP model for accident analysis was created based on the previously published literature. CAST analysis was performed to find the causal factors of the components and between the components. Results: The STAMP model visually showed the abstract and complex system control structure. The CAST analysis results could include all the causal factors from the previously published literature, and presented them holistically. Additional causal factors that were not presented in the literature were found. Conclusions: The holistic accident analysis results in this study will be helpful to establish comprehensive measures to prevent methanol or other chemical poisoning accidents. Therefore, it will be necessary to use systemic accident analysis methods in the field of occupational health.

Objectives: To determine the effect of the various type and number of shift work on sociopsychological stress in the university hospital nurses in Seoul, South Korea. Methods: Data was collected through a self-administered questionnaire that included general characteristics, the type and number of shift work in the past 4 weeks and the an sociopsychological stress based on PWI-SF. Logistic regression analysis was conducted to analyze the effect of shift work by types on sociopsychological stress of university hospital nurses using SAS 9.4 and it adjusted general characteristics by the additional models. Results: When the number of night shift work 3 or 4 compared to 0, sociopsychological stress was significantly high(OR=2.16, 95% CI=1.29-3.65). When 5 or more, it was higher(OR=2.39, 95% CI=1.55-3.72). Two continuous night shift work compared to 0 increased sociopsychological stress(OR=2.37, 95% CI=1.49-3.81) and 3 or more even more(OR=2.70, 95% CI=1.72-4.27). If the shift work type changes 14 or 15 times compare to below 11, sociopsychological stress is increased and even higher when 15 or more times but it's not significant after adjusting for covariates. Conclusions: It suggests that workplace with nurse expose to shift work should be on lookout for more than three night shift work, more than two continuous night shift work and more than 14 shift work change which can lead to burnout, absenteeism, depression and decreased productivity.

Objectives: To validate the effectiveness of a real-time chemical exposure monitoring system developed by KOSHA (Korea Occupational Safety and Health Agency), we applied the system to a workplace in the electronics industry for 153 days. Methods: The monitoring system consisted of a PID chemical sensor, a LTE communication equipment, and a web-based platform. To monitor chemical exposure, four sets of sensors were placed in two manufacturing tasks - inspection and jig cleaning - which used TCE as a degreasing agent. We reviewed previous reports of work environment measurements and conducted a new work environment measurement on one day during the period. The PID sensor systems detected the chemical exposure levels in the workplace every second and transmitted it to the platform. Daily average and maximum chemical exposure levels were also recorded. Results: We compared the results from the real-time monitoring system and the work environment measurement by traditional methods. Generally, the data from the real-time monitoring system showed a higher level because the sensors were closer to the chemical source. We found that 28% of jig cleaning task data exceeded the STEL. Peak exposure levels of sensor data were useful for understanding the characteristics of the task's chemical use. Limitations and implications were reviewed for the adoption of the system for preventing poisoning caused by chemical substances. Conclusions: We found that the real-time chemical exposure monitoring system was an efficient tool for preventing occupational diseases caused by chemical exposure, such as acute poisoning. Further research is needed to improve the reliability and applicability of the system. We also believe that forming a social consensus around the system is essential.

Objectives: The climate crisis has arrived and heat-related illnesses are increasing. It is necessary to discover new high-heat risk industries and understand the environment . It is also necessary to prioritize risks of industries that have not been included in the management target to date. The study was intended to monitor and evaluate the thermal risk of high-priority workplaces. Methods: A prioritization method was developed based on five factors: occurrence of and death due to heat-related illnesses, work environment monitoring, indoor work rate, small heat source, and limited heat dissipation. it, was applied to industrial accidents caused by heat-related illnesses. Wet bulb temperature index and apparent temperature were measured in July and August at 24 workplaces in seven industries and assessed for thermal risk. Results: The wet bulb temperature index was in the range of 23.8~31.9℃, and exposure limits were exceeded in the growing of crops, food services activities and accommodation, and building construction. The apparent temperature was in the range of 26.8~36.7℃, and exceeded the temperature standard for issuing heatwave warnings in growing of crops, food services activities and accommodation, warehousing, welding, and building construction. Both temperature index in growing of crops and building construction were higher than the outside air temperature. Conclusions: In the workplace, risks in industries that have not be controlled and recognized through existing systems was identified. it is necessary to provide break times according to the work-rest time ratio required during dangerous time period.

Objectives: The study was to examine the features of three-dimensional(3D) face dimensions and to develop fit test panels for the labor population using respirators in South Korea. Methods: This study was part of the first-year work of a two-year-project conducted at Occupational Safety and Health Research Institute in 2021. After 3D head dimensions data were collected from Size Korea Center managing Sixth Size Korea databases, 3D face dimensions DB for the South Korean labor population was established for 21 items of face dimensions in line with the ISO/TS 16976-2 and KS A ISO 15535. With the South Korean labor population 3D face dimensions DB, in accordance with the ISO/TS 16976-2, the descriptive statistics of 3D face dimensions were calculated and two fit test panels were developed. Results: A total of 2,752 subjects were finally determined and they were 52.9% for male, 41.2% for the highest age-group of 15-29, and residents in the capital area. Mean and standard deviation were obtained for each of the 21 3D face dimensions items for the South Korean labor population. Among the items, male and female face widths were 137.6±5.7 mm, 133.2±5.0 mm, respectively. Male and female face lengths were 116.6±7.0 mm, 107.8±6.8 mm, respectively. Two new South Korean fit test panels, a bivariate test panel and a principal component analysis test panel, were developed using the 3D face dimensions DB as well. Conclusions: Using the 3D face dimensions DB, the mean and standard deviation were featured for each of the 21 items and also the two fit test panels were newly developed in the study. It is suggested that the study outputs should be utilized practically and effectively in selection, use, and management of respirators at work, expecting that respiratory protection can be furthermore improved for respirator users including labor population across the country.