The random pulse width modulation(RPWM) on the noise and vibration abatement in inverter-fed induction motor drive is presented. This paper describes a RPWM technique based on space vector PWM strategy for shaping the switching noise spectrum in such a way it can merge with the natural system noise. To verify the validity of the proposed RPWM scheme, the experiment based on the TMS320 C3l microprocessor was executed. Finally, the simulation and experimental results will be given to demonstrate the effectiveness of the proposed RPWM technique.

The reliability of power electronics system is very important In industrial, commercial and military applications. This paper presents the principles for NPC inverter as an available technology for the design and implementation of adaptive fault tolerant systems. The fault tolerance is obtained by the use of the particular construction. The control method is proposed to get the sinusoidal load current with constant amplitude. The strategy described in this paper is expected to provide an economic alternative to more expensive redundancy techniques which find justification only in a few specialized application.

The 3-level converter/inverter system is very efficient in the ac motor drives of high voltage and high power application. This paper proposed a simple method to diagnose faults using change of current vector pattern in space vector diagram when the faults occurrence in the 3-level inverter and a control method that can protect system from unbalance of the neutral point voltage according to faults. The validity of the proposed method is demonstrated by the simulation results.

This paper presents a high frequency (HF) link current-fed inverter fur fuel cell applications. The circuit topology, operation and control method of the proposed HF link current-fed inverter are presented. The active cancellation technique of the 120Hz input harmonic current is also considered. The simulation results are provided to show the feasibility of the proposed inverter scheme.

본 연구에서는 변조지수 M이 큰 영역에서는 고조파 스펙트럼의 광대역화 효과가 저하되는 2상 랜덤 중앙 정렬 변조기법 (Random Centered Distribution PWM : RCD)기법의 문제점을 해결하고자 멀티 영벡터 2상 RCD (Multi Zero Vector RCD : MZRCD) 변조기법을 제안하였다. 제안된 2상 MZRCD기법은 변조지수 M=0.7을 기준으로 하여 M이 0.7보다 큰 영역에서는 영벡터를 V(111)로 선택하고, 0.7보다 작은 영역에서는 V(000)을 선택한다. 제안된 방법을 유도모터 구동시스템에 적용해 본 결과, M이 0.7이상인 영역에서도 모터의 전압/전류 및 소음 스펙트럼의 광대역화 특성이 종전의 방법에 비하여 우수함을 확인할 수 있었다.

In this paper, the improved performance of small aircraft onboard generator were described. As the characteristics of the field coil which are a major parameters of generator were improved, the system bandwidth could be increased, therefore the generator could also be satisfied with fast characteristic loads. Established the brief control model of the generator, it could be possible to do the analysis of generator performance, and improve the operational stability of the generator system using the control model.

On analyzing the power circuit of a DVR system, control limitations and control targets are presented for the voltage compensation in DVRs. The control delay in digital controllers increases the dimension of the system transfer function one degree higher which makes the control system more complicate and more unstable. Based on the power stage analysis, a novel controller for the compensation voltages in DVRs is proposed by a feedforward control scheme. Proposed controller works well with the time delay in the digital control system. This paper also proposes a guide line to design the control gain, appropriate output filter parameters and inverter switching frequency for DVRs in digital controllers. Proposed theory is verified by an experimental DVR system with a typical digital controller.

본 논문에서는 직류선로 접지의 보호알고리즘을 제안한다. 전형적인 보호알고리즘과 비교하면 제안된 알고리즘은 공급선로와 고장선로 사이의 차이를 구별하는 장점을 갖는다. 제안된 알고리즘의 내용은 블록킹 필터와 PLC(Power Line Carrier)의 사용에 의해서이다. 시뮬레이션의 결과는 제안된 알고리즘이 매우 유용함을 나타낸다.

본 논문은 새로운 HVDC 필터의 구조에 대하여 제안한다. 제안된 방법은 수동필터와 능동필터로 구성된 필터이고, HVDC에서 발생하는 고조파 중에서 가장 우세한 고조파인 11차와 13차를 제거하기 위한 목적으로 설계를 하였다. 또한 11차와 13차 고조파 제거를 위하여 하나의 수동필터만을 사용하였으므로 기존의 시스템에 비하여 경제적 이점이 있다. 제안한 방법은 PSCAD/EMTDC를 사용하여 이를 입증하였다.

In this paper, the authors propose a new high performance Built-in Type spindle motor drive using vector-controlled technique at 15,000 r/min. Control method is changed by variation of motor speed in a conventional Built-in type spindle drive. In the drive system to be presented, the conventional vector control is used in the low-speed range, and the vector control without encoder is used in the high-speed range. Furthermore, in order to drive the motor from 0 to 15,000 rpm smoothly, the vector control with encoder in the low-speed range (from 0 to 8,000 rpm) is utilized and the vector control without encoder in the high-speed range (from 8,000 to 15,000 rpm) is utilized. This paper describes problem of control method in conventional spindle drive and proposes control method as variation of motor speed

This paper presents new interpolation algorithm for measuring high resolution position information which is propered to nano servo control motor using analog quadrature encoder. In the past, there is a large memory and two high price A/D converter for high resolution analog quadrature encoder interpolation. but this paper show that it can make high resolution interpolate using small memory, one A/D converter and comparator. Experimental results show that the proposed algorithm for high resolution position is useful.

신재생에너지 개발을 위한 권선형유도발전기의 유효전력제어와 무효전력제어에 대해 고찰하였다. 10kW DFIG에 양방향 AC/DC/AC 전력변환장치를 적용한 실험을 통해 유효전력제어와 무효전력제어를 검증하였고, 운전 개시 속도를 결정하는 방법과 전력변환장치 용량을 고려한 제어방법, 그리고 역률 가변을 통해 저속도 영역에서의 에너지 회수방안에 대해 고찰하였다.

3kW grid-connected photovoltaic(PV) systems and data acquisition system are constructed for performance analysis of PV system at field demonstration test center of Gwang-Ju in Korea. As climatic and irradiation conditions are varied, operation characteristics of the PV system are collected and analyzed in data acquisition system. From these results, the performances of PV systems have simulated and evaluated using simulation tool In comparison with actual value of data acquisition system of field demonstration test center. Furthermore, performance of each PV system e.g. electric power and loss factor is reviewed.

The paper presents implementation of a PV fuzzy logic power tracking controller. Using maximum power point tracker with the intermediate converter can increase the system efficiency by matching the PV system to the load. A new fuzzy MPPT is proposed, where fuzzy inputs parameters are dp/dI and the last incremental of duty of duty ratio $L{\delta}D$, and the output is the new incremental value $(new{\delta}D)$ according to the maximum power point under various illumination levels.

This paper proposes a maximum output power control of grid-connected wind power generation system using cage-type induction generators. For generator control, indirect vector control is used, where d-axis current controls the excitation level and q-axis current controls the generator speed. The generated power flows into the utility through the grid-side converter, by which the do link voltage is controlled to be constant and the ac current is controlled in sinusoid and. The generator speed is adjusted according to wind speed for extracting maximum power generation. Experimental results are shown to verify the validity of the proposed scheme.

As rapid growth of energy demand in line with modern society's industrialization led to environmental pollution by fossil fuels, there are more and more interest and international research on energization of water, which is clean energy and comprising $70\%$ of earth. In offshore countries, the water is commercially used already and water has very attractive characteristics in terms of economy and efficiency compared to the existing gas welder. Brown Gas welder does not produce $CO_2$ from combustion of Hydrogen-Oxygen-Gas, which was gained by electrolysis of water, In this paper, the result from operating characteristic improvement of Gas Generator and Current-Controlled converter is to be considered into design in electrode, source/ controller, standized into level of whole system design base.

For increasing power of photovoltaic systems, serial and parallel connection needed. In parallel connection, a desirable characteristic of parallel-connected supply system is that individual converters share the load current equally and stably. The current sharing(CS) can be implemented using two approaches. The first one, known as a Droop method, and the other is Active current-sharing. In Droop method, current distribution characteristics relies on the high output impedance of each converter. This scheme is more simple and no need interconnections. but also has a disadvantages of degrading current sharing characteristics. In this paper, using droop method at multiful-parallel connection with it's convenience and simplicity.

Many single-stage PFC(power-facto.-correction) ACHC converters suffer from the high link voltage at high input voltage and light load condition. In this paper, to suppress the link voltage, a novel high power factor high efficiency PFC AC/DC converter is proposed using the single controller which generates two gate signals so that one of them is used far gate signal of the flyback DC/DC converter switch and the other is applied to the Boost PFC stage. A 130w prototype for LCD monitor adapter with universal input $(90-265V_{rms})$ and 19.5V 6.7A output is implemented to verify the operational principles and performances. The experimental results show that the maximum link voltage stress is about 450V at 270Vac input voltage. Moreover, efficiency and power factor are over $84\%$ and 0.95, respectively, under the full load condition.

Recently, many nations have released standard such as IEC 1000-3-2 and IEEE 519 which impose a limit on the harmonic current drawn by equipment connected to AC line in order to prevent the distortion of an AC line. Among the wide variety of active methods for improving power factor and harmonic distortion, the boost converter is very effective because it has a continuous line current , small choke filter and high power factor. In high power application, however, the bridge diode loss in the boost converter has made the efficiency lower and the temperature of the board higher. A new approach without bridge diode to make the same characteristics of the conventional boost converter has also been developed. This paper present the comparisons between the continuous current mode(CCM) operated conventional boost converter and the boundary current mode(BCM) operated the bridgeless boost converter for high efficiency and high power factor.

A ZVT PWM Boost Converter is proposed to reduce current stresses and conduction losses of main switch in a conventional circuit. By attaching resonant inductor Lr1 in parallel with capacitor Cr, the resonant circulating current is diverted to the additional component and then the main switch is subjected to minimum current stresses same as those in their PWM counterparts. Moreover, the operation of the auxiliary switch in a half wave mode to prevent reverse resonant energy from freewheeling can be able to lessen the conduction losses. The operation principles of the proposed converters are analyzed using the PWM boost converter topology as an example. Theoretically analysis and experimental results verify the validity of the boost converter topology with the proposed circuit.

Recently, a fuel cell with low voltage and high current of electronic output characteristics is remarkable for new generation system. It needs both a dc-dc boost converter and do-ac inverter to be used in domestic power. Therefore, this paper presents do-dc boost converter with ZVS for fuel cell generation system This topology has several advantages, which are ZVS characteristics of all of main and auxiliary switches, reduction of reactor component size because of high frequency switching, and low rated voltage stress of the switches. In this paper, theoretical analysis, operation principle, and design procedures are presented. And simulation results from Pspice are presented to validate the theoretical analysis.

This paper explained algorithm for a initial pole position estimation of a permanent magnet linear synchronous motor(PMLSM). Generally this motor is considered initial pole position with a position sensor such as incremental encoder for the precise initial pole position estimation and high performance. But this is based on the principle that the initial pole position is accomplished by the PI controller using the maximum values of a position error generated by the new proposed two reference frames and also by using a rated force for input. the proposed algorithm does not utilize the general methods such as impedance ratio, EMF and using the magnetic saturation. In other words, this can be applied without respect to variety of the motor structure because of insensitivity to the motor parameters. In conclusion, simulation results are presented to confirm performance of initial pole position estimation method.

SRM(switched reluctance motor) provides a excellent adjustable speed and torque characteristics. SRM has the possibility of maintaining full power over a wide speed range. So, many attempts are being done from home appliances to industrial applications. Especially, a traction drive of an SRM is one of a good application for it's DC-series characteristic. However, because of the switching mechanism and reluctance torque, it has some disadvantage Of noise and Vibration. It is difficult to adopt to an appliance demanding silency. A performance and noise tests with 6/4 and 12/8 SRM were done to compare the characteristics.

The proposed rotor time constant estimation method can be applied to the direct vector control system of induction motor with flux observer In this paper the flux observer proposed by Gopinath model are used. This paper presents a new scheme for on-line estimation of rotor time constant using estimated rotor flux phase and current model rotor flux phase. The major advantage of this method are its dynamic correction capability, simplicity and accuracy as well as independence from change in motor parameter. simulation results are presented which demonstrate the effectiveness of the on line rotor time constant estimation.

This paper describes the sensorless technique for the surface-mounted permanent-magent synchronous motor(SPMSM or PMSM) drive based on magnetic saliency. The control technique is a sensorless control algorithm that injects the high frequency voltage to the stator terminal in order to estimate the rotor position and speed. The rotor position and speed for sensorless vector control is achieved by appropriate signal processing to extract the position information from the stator current in the low speed range including zero speed. Proposed sensorless algorithm using the double-band hysteresis controller and initial rotor position detection exhibits excellent reference tracking and increased robustness. Experimental results are presented to verify the feasibility of the proposed control schemes.

This paper proposes a speed-sensorless induction motor control system using the rotor flux error. The rotor flux observer uses the reduced- dimensional state estimator technique instead of directly measuring the rotor flux. The estimated rotor speed is obtained directly from the electrical frequency, the slip frequency, and the rotor speed compensation with the estimated q-axis rotor flux. To precisely estimate the rotor flux, the actual value of the stator resistance, whose actual variation is reflected, is derived. For fast calculation and improved performance of the proposed algorithm, all control functions are implemented in software using a digital signal processor (DSP) with its environmental circuits. Also, it is shown through experimental results that the proposed system gives good performance for the speed-sensorless induction motor control.

This paper describes an initial pole position estimation method of a magnetic pole sensorless permanent magnet synchronous motor(PMSM) with an incremental encoder, The accurate initial pole position is estimated by using an efficient numerical method of Secant Method, which finds either of two zero torque/force positions and then the correct d-axis. It can be simply applicable to both rotary and linear PMSM because it only requires the tuned current controller and the relative position information. The experimental results show the validity of the proposed method with respect to highly accurate pole position estimation under the moderate moving distance and convergence time.

Generally, PM BLDC drive system is necessary that the three Hall-ICs evenly be distributed around the stator circumference and encoder be installed in case of the 3 phase motor. So, the Hall-ICs are set up in this motor to detect the main flux from the rotor, and the output signal from Hall-ICs is used to drive a power transistor to control the winding current. However, instead of using three Hall-ICs and encoder, we used only two Hall-ICs for the permanent magnet rotor position and for the speed feedback signals, and also for a micro controller of 16-bit type (80C196KC) with the 3 phase PM BLDC whose six stator and two rotor designed. Two Hall-IC Hc and $H_B$ are placed on the endplate at 120 degree intervals, and with these elements, we estimated information of the others phase in sequence through a rotating rotor.

본 논문에서는 PID제어기를 이용해 외란이 존재하는 2차시스템 특성을 갖는 전동기를 제어하는 경우 외란제거와 최적제어가 동시에 될 수 있는 PIB파라메터를 면역알고리즘을 통해 구하였다. 외란제거를 위해 $H{\infty}-norm$을 응용하여 제어시스템의 외란제거 조건들을 제시하고 이 조건들을 만족하는 전동기 제어용 PID제어기를 설계하였다. 설계된 PID제어기의 최적 파라메터를 구하기 위해 면역 알고리즘을 적용하였고 최적 파라메터를 평가하기 위하여 ITSE(Integral of time weighted squared error)성능지수를 이용하여 만족할 만한 결과를 얻었다.

In this paper, a PWM Cuk AC-AC converter for WCF applications such as AC line conditioner, phase shifter is presented. The PWM Cuk AC-AC converter is modelled by using complex circuit DQ transformation whereby the characteristics equations such as voltage gain and the interested voltage and current is analytically obtained. Finally, the PSIM simulation show the validity of the modelling and analysis.

This paper describes a new notches generator for the test of custom power devices such as UPS, DVR, Active Power Filter, etc. The magnitude, width, polarity, and position of the notches generated by the proposed scheme can be varied with simple control. The scheme has good features of simple structure, high reliability, and the capability of arbitrary several notches generation. The circuit operation is described and the usefulness of the scheme is verified through simulations.

In this paper, the design and implementation of a high power(300W) forward converter using a planar transformer is presented. The overall size and volume of the converter is decreased by replacing a planar transformer in stead of using a conventional winding transformer. Due to the decreased size and volume, power density of the applied forward converter is increased. Also, in this paper, the 300W ZVS forward converter with active clamp snubber circuit is compared to the 300W hard switching forward converter.

This paper presents an improved soft switching buck converter using a non-dissipative snubber, which is composed of a tapped inductor, two snubber capacitors and three snubber diodes. The proposed buck converter achieves zero voltage turn-off in the main switch and freewheeling diode. The Proposed Soft Switching buck converter is verified through the simulation, relevant equations, analysis and experimental results.

한국전력공사에서는 전압원 인버터형 FACTS 기기인 UPFC를 전남 강진군 강진변전소에 설치하였다. 강진 UPFC는 한전과 (주)효성이 공동으로 투자하고, 지멘스와의 기술제휴를 통해 개발하였으며, 40MVA 병렬인버터, 40MVA 직렬인버터로 구성되어 총 80MVA 용량이다. 강진 UPFC는 GTO를 이용한 3레벨 인버터 모듈 20MVA 총 4대로 구성되어 있으며, STATCOM, SSSC, UPFC의 3가지 운전모드를 갖는다. 현재 병렬인버터는 강진 모선전압 제어, 직렬인버터는 강진-장흥간의 조류제어에 기여하며, 상용운전 중이다. 본 논문에서는 강진 UPFC 커미셔닝 및 그 운전 결과를 소개하였다.

본 논문에서는 PWM 펄스를 랜덤하게 위치시킬 수 있는 새로운 3상 공간벡터 RPWM (Random PWM) 기법을 제안하고 있다. 기존의 RPWM 방식과 달리 SVPWM에 의해 발생된 PWM 펄스를 랜덤하게 위치시키는 원리를 각 섹터마다 달리 적용하여 쉽게 RPWM을 구현하는 기법을 제안한다. 제안된 기법의 타당성 검증을 위하여, 제안된 RPWM (Random PWM) 기법 알고리즘에 대해 DSP를 이용한 IGBT 인버터 구성에 의한 실험을 수행하였다. 이에 대한 결과 중, 특히 10000 rpm 이상의 고속운전특성에서의 인버터 출력 전압 및 전류의 고조파 스펙트럼을 넓은 주파수 영역으로 고루 분산시켜 제안된 RPWM의 특정고조파의 저감효과를 입증하고자 한다

본 논문에서는 고주파 스위칭 시 스위칭 손실의 감소, 구현의 용이성 및 인버터 제어를 위하여 요구되는 연산시간 감소 등 다양한 장점을 가진 2-LEG 인버터를 대상으로, 새로운 RPWM(Random PWM) 기법에 의한 3상유도전동기 구동 방식에 대하여 서술한다. 기존의 RPWM 방식과 비교하여 제안한 RPWM 기법으로부터, 10000(rpm) 이상의 고속운전 영역에서의 인버터 출력전류의 고조파 스펙트럼을 넓은 주파수 영역으로(특정주파수의 side band) 고루 분산시켜 RPWM의 고조파 저감효과에 대한 우수성을 입증하고자 한다. 이러한 과정에서 제안된 RPWM 기법을 적용한 알고리즘에 대하여 DSP를 이용한 IGBT 인버터에 의한 실험을 수행하여, 이로부터 그 결과를 검토하여 제안된 기법의 타당성을 검증하고자 한다.

본 논문에서는 RPWM(Random PWM) 방식을 사용한 3상 유도전동기 구동 시스템의 스위칭 주파수 가변에 따른 구동 특성을 비교 분석하고자 한다. 기존의 RPWM 방식과 본 논문에서 제안한 RPWM 기법을 이용하여 스위칭 주파수 가변에 따른 $M_f$ 변화에 대한 구동특성을 비교 분석하고, 특히 10000[rpm] 이상의 고속운전특성에서의 인버터 출력 전압 및 전류의 고조파 저감효과를 제안된 기법으로부터 확인할 수 있다. 이러한 과정에서는 제안된 RPWM 기법 알고리즘에 대한 타당성 검증을 위해 DSP를 이용한 IGBT 인버터로부터 개별 스위칭 주파수별 실험을 하고, 그 결과의 취득으로부터 스위칭 주파수별 운전 특성을 분석하고자 한다.

This paper presents a position sensorless control system of Switched Reluctance Motor(SRM) using Neural Network. The basic algorithm of this scheme is based on the flux linkage characteristic according to the phase currents and rotor position. A sufficient experimental data was used for neural network training. The proposed position sensorless control system was realized using TMS320F240 DSP. The experimental result shows some good results, and verifies the possibility of this algorithm.

This paper combines the adaption of MRAS with the ability of NN for better modeling of nonlinear systen It presents an MRAS using an NN in the adaption mechanism. The technique is applied to a IPMSM drive. The torque constant and stator resistance variations on the speed and position estimations over a wide speed range has been studied. The NN estimators are able to track the varying parameter of different speeds with consistent performance. The validity of the proposed estimator is confirmed by the operating characteristics controlled by neural networks control.

This paper is proposed to position and speed control of interior permanent magnet synchronous motor(IPMSM) drive without mechanical sensor. A gopinath observer is used for the mechanical state estimation of the motor. The observer was developed based on nonlinear model of IPMSM, that employs a d-q rotating reference frame attached to the rotor, A gopinath observer is implemented to compute the speed and position feedback signal. The validity of the proposed scheme is confirmed by various response characteristics.

This paper presents a design and characteristics analysis of an SRM drive for EPS application. A rack mounted EPS system is considered in this paper. In the unrestricted design conditions, motor parameters are determined for sufficient torque and speed. For the smooth torque generation and simple circuit of power system, 12/8 motor drive is considered. With FEM and magnetic circuit analysis, redesigned motor is simulated to meet the requirement of specifications. Effectiveness of the suggested SRM drive for EPS application is verified by redesigned motor drive tests.

For a power source of usual electronic devices such as PDA, smart phone, UPS and electric vehicle, the battery made of serially connected multiple cells is generally used. In this case, if there are some unbalanced among cell voltages, the total lifetime and the total capacity of the battery are limited to a lower value. To maintain a balanced condition in cells, an effective method of regulating the cell voltage in indispensable. In this paper introduced a method for battery balancing system using dissipation in the resistance.

액정 디스플레이의 백라이트에 사용되는 냉음극 방전램프(CCFL: Cold Cathode Fluorescent Lamp) 구동 인버터의 설계함에 있어 압전 변압기(Piezoelectric Transformer)를 사용하였으며, 파라미터 선정 및 최적화를 하여 실험을 통해 검증하였다. 적용한 압전 인버터로는 푸시-풀(Push-pull)과 하프-브리지(Half-bridge) 회로이며, 휘도 제어기법으로는 아날로그(Analog)와 버스트(Burst) 방법을 사용하였다. 푸시-풀 인버터의 경우 아날로그 제어방식으로 제어전압 2.5-4.5V에서 출력전류 1-6mA(최소)로 휘도 $0-100\%$ 특성을 보였다. 입출력 효율로 18.6(최소)-90.3(최대)$\%$를 얻었으며, 버스트 제어방식에서는 듀티비 $5-50\%$에서 1-6mA의 제어성능을 보였다. 인버터의 입출력 효율은 13.6(최소)-82.1(최대)$\%$를 얻었다.

Recently, UPS(Uninterruptible Power Supply) have been largely used to improve power souse quality as well as to protect critical loads such as computer, industrial system, medical equipment, etc, against power outage by providing clean and uninterrupted power under power supply disturbance or interruptions. But UPS is bulky because used battery. So, UPS size issue have received attention in the power electronics industry. Therefore, this paper proposed a implementation of inside of the computer power supply with UPS by the one-chip microprocessor to minimize UPS size. To verify the proposed power supply, the detail simulation and experiment results indicate that high-frequency switching and operation UPS can be achieved.

This paper deals with stand-alone PV power generation system with charge and discharge controller for the LED road sign. Main power source of PV system are generally solar cell and battery. Therefore PV system can be classified into variable types in accordance with connection type between battery and solar sell. Mainly used on of them is direct connection type which has advantage such as simple structure and simple controller. To verify the proposed PV generation system for the LED road sign, the detail simulation and experiment results indicate that operating characteristics are verified by experiment with a laboratory prototype in this paper.

Short-circuited can have significant effects on a generator and its performance. One of effective method detecting inter-turn short circuits on round rotor winding is a method using sensor detecting. But the method needs duplicate design of sensor for characteristic change according to types and forms of generator. Thus rotor shorted-turn diagnosis method without sensor is needed for detecting short turn when generator is driven. Diagnosis method without sensor depend on change of electric property in generator For the reason, this paper presents characteristic analysis of shorted-turns in generator by detecting the output voltage of generator.

The connectorless power supply system on that multi-contact causes confidence when the wiring reconstructed in the rear. As you see above, contact points between sets and indoor space cause inferior function of audio frequency so it needs to be eliminated. This paper explains the structure of connectorless power supply to supply the system with power crossing the air gap in the part of inductively in the connectorless power supply of both magnetic and electrical model. To get maximum output of electrical load, compensating capacitor compensates to show inter-inductance, lequeage-inductance reducing the track-inductance and access the conditions for resonance. At that time it accesses the maximum electric power. The small change of the value of compensating capacitor causes the changes of maximum electric power. Here the power electronics technology is used not only in the industrial machinery but also in the home appliances so the switching power supply is used to actualize the miniaturization, lightweight, and high efficiency. Generally the condenser input methods are widely used in the rectification circuit of switching power supply, but condenser input method generate great quantity of high frequency components because with this method the current flows in the power input filtering condenser only around value of peak of ac input voltage. To solve these problems, installation of power factor improve circuit on the front of filtering capacitence was considered. Several methods were suggested regarding, but the active filter method which makes smalliging and highly power factor possible are the produce main stream. IC for power factor improvement can be utilized by CMOS process proposing low power consumption. When the high power factor is considered seriously in the power factor improvement circuit, active filter method is selected. In the active filter method, the boost converter is used. Regarding this ·the boost converter is needed.

국내 난방 시스템은 대부분 화석에너지를 열원으로 하는 온수순환방식이다. 화석에너지를 사용하기 때문에 난방 시스템 가동에서 발생되는 공해는 대기-오염의 여러 원인 중 하나이며 가동 효율도 떨어진다. 이러한 단점들을 보완하기 위하여 새롭게 보급되고 있는 난방 시스템 중 히프파이프를 이용한 난방시스템은 전기에너지를 열원으로 사용하는 청정에너지로서 기존 난방시스템 보다 $40\%$의 에너지 절감 효과를 나타내고 있다. 본 논문은 전기에너지를 사용하는 히팅 시스템의 제어를 위하여 개발된 컨트롤러에 관한 것이다.

BT에 대한 관심이 높아지면서 식물 종자 및 작물의 배양 기술에 관한 연구가 활발해 지고 있다. 이 연구들은 주로 백신, 종자 등에 대해 연구가 이루어지고 있는데, 이를 위해 다양한 연구 환경의 구축이 필요한 시점이다. 본 논문에서는 여러 가지 분야 중에서도 빛의 파장대에 따른 작물의 배양 조건 분류를 위한 특수램프 개발에 주목적을 두고 인버터 최적조건 설계를 위하여 Ansys S/W를 사용, 램프 전원용 인버터의 열 분포를 시뮬레이션 하였다.

Increasing of the use nonlinear power electronics equipments, power conditioning systems have been researched and developed for many years to compensate the harmonic disturbances and the reactive power. The main function of power conditioning systems is to reduce harmonic distortions, since extensive surveys quantify the problems associated with electric networks having non-linear loads. The main function of power conditioner compensates the current instead of the voltage. Therefore the inverter used in power conditioner is mostly current controlled type. In this paper, the proposed current control algorithm is analysed and discussed about how to design the controller which can apply power conditioning operation for grid-connective PV power system. And also proposed control system. To verify the proposed current control algorithm, a comprehensive evaluation with theoretical analysis, simulation, experiment results is presented.

Simulation model of induction type fixed speed wind power generator is developed. It is shown that the peak value of inrush current during start up changes according to the firing angle control strategy of soft starter. New proposed firing angle control scheme showed $25\%$ of reduction of peak current which results in smaller drop of gird voltage at the point of common coupling during start up.

As the maximum power operating point (MPOP) of photovoltaic (PV) power systems changes with changing atmospheric conditions, the efficiency of maximum power point tracking (MPPT) is important in PV power systems. Many MPPT techniques have been considered in the past, but techniques using microprocessors with appropriate MPPT algorithms are favored because of their flexibility and compatibility with different PV arrays. Although the efficiency of these MPPT algorithms is usually high, it drops noticeably in case of rapidly changing atmospheric conditions. In this paper, we proposed a new MPPT control method called improved perturb and observe method (ImP&O), anda simple voltage and current characteristic equation of a PV array for PV array simulator. Experimental results verify the accuracy and excellent performance of the proposed MPPT method. ImP&O algorithm is very simple, and has successful tracked the MPOP, even in case of rapidly changing atmospheric conditions.

The solar cells should be operated at the maximum power point because its output characteristics are greatly fluctuated on the variation of insolation, temperature and load. The output power of solar cell is DC, therefore it is necessary to install an inverter among electric power converts. The inverter have to supply a sinusoidal current and voltage to the load and the interactive utility line. In the paper, the proposes a photovoltaic system designed with a step up chopper and single phase PWM voltage source inverter. Synchronous signal and control signal was processed by microprocessor for stable modulation. The step up chopper operates in continuous mode by adjusting the duty ratio so that the photovoltaic system tracks the maximum power point of solar cell without any influence on the variation of insolation and temperature because solar cell has typical dropping character. The single phase PWM voltage source inverter consists of complex type of electric power converter to compensate for the defect, that is, solar cell cannot be developed continuously by connecting with the source of electric power, from 10 to $20\%$. The single phase PWM voltage source inverter operates in situation that its output voltage is in same phase with the utility voltage. The inverter supplies an ac power with high factor and low level of harmonics to the load and the utility power system.

This paper presents experimental operation with utility invertactive 3kW photovoltaic generation system. And that describe configuration of utility interactive photovoltaic system which power supply for Demonstration Complex. The status of photovoltaic generation system components and interconnection and safety equipment will be summarized. This paper discusses property operation state which system endure division of power for Demonstration Complex.

The developments of the hybrid energy are necessary since the future alternative energies that have no pollution and no limitation are restricted. Currently power generation system of MW scale has been developed. However, even photovoltaic system cannot always generate stable output with ever-changing weather condition. In this paper, sub power generator for hybrid system(photovoltaic 500[W], wind power generation 400[W]) was suggested. Sub power Generator that uses elastic energy of spiral spring to photovoltaic system was also added for the present system. In an experiment, when output of photovoltaic system gets lower than 24[V] (charging voltage), power was continuously supplied to load through the inverter by charging energy obtained from generating rotary energy of spiral spring operates In DC generator. Also, control algorithm of sub power generator is used genetic algorithm(GA).

Digital environment that is represented to internet is displacing business way of industry and business achievement way with the fast speed being giving great change on life whole, improve existence business process utilizing internet and Web connection technology, information superhighway to tradition industrialist manufacture and e-transformation's propulsion that wish to maximize productivity and administration efficiency is spread vigorously. In this paper, we wish to accomplish generation equipment's heighten stability and believability through remote monitoring and control of BIPV system. This paper describes the design of the monitoring system for sensing the monitoring data and indirect controlling of the BIPV system. Most of the conventional monitoring system depend on the special hardware and software. Basic design goal of monitoring system is to provide the convenience for the user and the portability for the system. In order for the system to fulfill its requirements, it was designed using Labview GUI facility based on the Windows 2000 environment of IBM PC compatible and Add-on card based on the TCP/IP protocol. Advantage of the monitoring system are a personnel expenses curtailment effect, free of the place restriction and unmanned system of the generation plants, etc.

This paper deals with the development of the PMSM(Permanent magnet synchronous motor) system for the electrical actuator, For the high control performance and reliability of PMSM, accurate information of rotor position is essential. Most of PMSM for the position control use the encoder or resolver for the information of rotor position. But these are very expensive. So, in this paper, using of the magnetic and linear hall-effect sensor is proposed. It can reduce the cost of motor systems and get the good performance of PMSM control.

This paper is proposed a new linear actuator with the permanent magnet on the mover. This linear actuator is designed to produce the vibration of a osillator. In order to evaluate its dynamic performance, the equivalent coupling parameter between mechanical and electromagnetic equations of the linear actustor, which is considered the magnetic nonlinear phenomena, is analyzed by the finite element method and estimated the thrust, displacement and acceleration with the simualation values and the experimenta ones.

The high power factor converters are classified step-up, step-up-down and step-down converter, The power conversion system must be increased switching frequency in order to achieve a small size, a light weight and a low noise. And the power system brings on a high efficiency and high power factor. When a switch of the step down converter is operated with a commercial frequency(60Hz), a reactor using the converter is gone with a great number of harmonics waveforms of low grade. As results of this, the converter is decreased input power factor and is increased system size. To improved these, this paper proposes a PSM(Pulse Size Modulation) control strategy operated with high power factor.

In this paper, a new energy recovery circuit for AC PDP(Plasma Display Panel) is proposed to decrease a sustain voltage and voltage stress on switching elements. In the proposed circuit, two auxiliary capacitors are connected directly to the power source through switching elements and inductors when ground potential is supplied to the panel. Therefore, the voltage across auxiliary capacitors can be increased by turns over the half of the source voltage. Because the intrinsic capacitance of PDP is charged sufficiently from the auxiliary capacitors, the level of sustain voltage and the voltage stress on the switching devices are decreased. To verify the validity of the proposed energy recovery circuit, computer simulations using PSpice program are carried out.

In this paper, compare and analyze existent MPPT algorithms. Existent algorithms have defects which don't generate it in a partial shade or low insolation. Therefore, to supplement it, we design improved IncCond algorithm consisted of a Aux. switch and capacitor with Generation Control circuit which can always obtain maximum generation power at the factor which is reduced generational efficiency by partial shade. Generation Control circuit is method which can always get maximum output power as it regularly controls each voltage of serial connected solar cell. Accordingly, it can improve efficiency and confidence of utility interaction inverter. Construction of system use a low price PIC16F87X. We analyze special character according to system operation through simulation and prove the validity through experiments.

Conventional vector control inverter is usually used for blower of air-accord equipment. In this paper, it is proposed that inverter is controlled by instantaneous following PWM controller. This controller compensate and follow for output voltage of inverter within one switching cycle as an error that compared output voltage of rectifier included much ripples with reference voltage of sine wave. It has not speedy response like vector controller, but the circuit is very simple as using analog integer. And it has advantages that develop input power factor, built small-capacity and low-cost because huge capacitor of voltage type inverter removed.