Structural Engineering and Mechanics

  • 제9권5호
  • /
  • Pages.417-432
  • /
  • 2000
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Analysis and design of metal-plate-connected joints subjected to buckling loads

  • Hussein, R.
  • 발행 : 2000.05.25
⟨ 이전 논문 다음 논문 ⟩

초록

A comprehensive analytic study has been conducted to investigate the instability problems of metal-plate-connected (MPC) joints in light frame trusses. The primary objective in this study is to determine the governing factors that constitute the buckling of the metal connectors and their effects on the structural response of joints. Another objective is to recommend design curves for the daily structural design of these joints. The numeric data presented in this paper has emerged from a broad base that was founded on over 350 advanced computer simulations, and was supported by available experimental results obtained by others. This basic-to-applied research includes practical engineering parameters such as size of gaps, shear lengths, gauge (plate thickness) of connectors, size of un-braced areas, failure modes, and progressive disintegration of joints. Square-end members have been emphasized though the results cover the custom-made fitted joints. The results indicate that chord shears cause and dominate the buckling of MPC joints, and the shear length has a more pronounced effect than the size of gaps. Further, large gauges and small un-braced areas improve the buckling response. Several practical recommendations have been suggested throughout the paper such as keeping the ratio of gap/shear length below 3/4 for improving the buckling strength. The study reveals that multi-area joints should not be simplified as single web-to-chord MPC joints such as keeping the ratio of gap/shear length below 3/4 for improving the buckling strength, even where one web is in tension and the other in compression. Finally, the results obtained from this study favorably agree with experimental data by others, and the classic buckling theories for other structural components.

키워드

참고문헌

  1. American National Standard Institute (1995), "National design standard for metal-plate-connected wood truss construction", ANSI/TPI 1-1995, TPI, Wisconsin, February.
  2. American Society for Testing and materials (1982), "Tensile strength properties of steel truss plates", ASTM E 489-81, ASTM Annual Book of ASTM Standards, PA.
  3. American Society for Testing and Materials (1982), "Shear resistance of steel truss plates", ASTM E 767-80, ASTM Annual Book of ASTM Standards, PA.
  4. American Society of Civil Engineers (1996), "Mechanical connections in wood structures", ASCE Manuals and Reports on Engineering Practice 84, NY
  5. Canadian Standards Association (1984), "Engineering design in wood (Working Stress Design) - A national standard of Canada", CAN3-086-M84, CSA, Canada, December.
  6. Canadian Standards Association (1980), "Method of test for evaluation of truss plates used in lumber joints", CSA Standard S347-MI980, Ontario, CA, January.
  7. Crovella, P. and Gebremedhin, K. (1990), "Analysis of light frame wood truss tension joint stiffuess", The Forest Product Journal, 40(4), April.
  8. Gebremedhin, K. and Crovella, P. (1990), "Analysis of light frame wood truss joint using an elastic foundation model", Proceedings of the 1990 International Timber Engineering Conference, Tokyo, Japan, October.
  9. Grossthanner, O. and Brakeman, D. (1993), "Overview of truss plate design and evaluation methods in the United States", Proceedings of the International Workshop on Wood Connectors, Las Vegas.
  10. Hussein, R. (1989), "Framework methods for orthotropic plates", Journal of Computers and Structures, 22(2), January.
  11. International Organization for Standardization (ISO) (1990), "Timber structures - testing of unilateral punched metal plate fasteners and joints", ISO 8969.
  12. Lucas, W.M. (1970), "Grid analysis of plates resting on elastic foundations", Bulletin of Engineering, No. 62, University of Kansas.
  13. Szilard, R. (1973), Theory and Analysis of Plates, Prentice Hall Inc., New Jersey.
  14. Timoshenko, S. (1936), Theory of Elastic Stability, McGraw-Hill Book Company, Inc., New York.
  15. Truss Plate Institute (1987), "Interim design methodology for PCT-ClI 2X4/2X6 wood trusses", TPI-85, TPI, Wisconsin, March.
  16. Wood Truss Council of America (1997), "Metal plate connected Wood Truss Handbook - A comprehensive guide to the design and use of metal plate connected Wood Trusses in construction Today", WTCA, Wisconsin, July.
  17. Yasutoshi, S. and Takemura, T. (1990), "Non-linear analysis of metal-plate wood trusses", Proceedings of the 1990 International Timber Engineering Conference, Tokyo, Japan, October.