• Korean Journal of Materials Research
• /
• v.12 no.6
• /
• pp.442-446
• /
• 2002

Design of microwave absorbers using high frequency properties of fiber reinforced composites are investigated. Two kinds of composite materials (glass and carbon) are used and their complex permittivity and permeability are measured by transmission/reflection technique using network analyzer. Low dielectric constant and nearly zero dielectric loss are determined in glass fiber composite. However, carbon fiber composites show the high dielectric constant and large conduction loss which is increased with anisotropy of fiber arrangement. It is, therefore, proposed that the glass and carbon fiber composites can be used as the impedance transformer (surface layer) and microwave reflector, respectively. By inserting the foam core or honeycomb core (which can be treated as an air layer) between glass and carbon fiber composites, microwave absorption above 10 dB (90% absorbance) in 4-12 GHz can be obtained. The proposed fiber composites laminates with sandwitch structure have high potential as lightweight and high strength microwave absorbers.

• Proceedings of the KIEE Conference
• /
• 1989.11a
• /
• pp.119-121
• /
• 1989

The properties of Pb-doped Bi-Sr-Ca-Cu-O Super-conductors prepared by solidstate reaction have been studied. Zero resistance was attained at l03K for the sample sintered 845[$^{\circ}C$]for 264hours and it was depended upon sintering conditions. From XRD data low Tc phase and high Tc phase were observed and the volume fraction of high Tc phase increased with increase in sintering period. The grain size increased with increase in sintering temperature and time.

• Journal of the Korean Ceramic Society
• /
• v.31 no.6
• /
• pp.678-684
• /
• 1994

The surface of alumina is capable of acquiring a change when it is in an aqueous solution. This surface change will have a strong influence on the surrounding ions, particularly those of opposite change known as the counter ions. A site-binding model of the {{{{ gamma }}-alumina/KCl(aq) interface was used to calculated theoretical surface ionization constants and P.Z.C.(Point of zero change) of {{{{ gamma }}-alumina. This paper was carried out to investigate the effect of calcination temperature on the acidic and electrical properties of pure {{{{ gamma }}-alumina prepared by the precipitation method from the Al(NO3)3.9H2O and NH4OH. From the experimental data it was shown that {{{{ gamma }}-alumina have a mainly Br nsted acid site. However, the acidity of {{{{ gamma }}-alumina decreased with increasing calcination temperature at strength Ho +9.3. The surface charge density of {{{{ gamma }}-alumina was increased with electrolyte ionic strength and calcination temperature.

• Journal of the Korean Ceramic Society
• /
• v.23 no.6
• /
• pp.59-65
• /
• 1986

Flexural strength fracture toughness and strengthening mechanisms of cordierite ceramics reinforced by SiC whiskers up to 40vol% were investigated. The specimens were hot pressed at Ar atmosphere. The porosity increased with the SiC whisker content. Flexural strength and single edge notch beam fracture toughness were measured up to 1,000$^{\circ}C$. Extrapolating to zero porosity the reinforced composites exhibited in-creasings in flexural strength and fracture toughness with the SiC whisker content. The composites were strengthened mainly by load transfer crack impediment and partially by crack deflection mechanisms. Impurities played an important role in determining the mechanical properties of the composites.

• Journal of Mechanical Science and Technology
• /
• v.20 no.7
• /
• pp.950-960
• /
• 2006

An output time delay always exists in practical systems. Analysis of the delay phenomenon in a continuous-time domain is sophisticated. It is appropriate to obtain its corresponding discrete-time model for implementation via a digital computer. A new method for the discretization of nonlinear systems using Taylor series expansion and the zero-order hold assumption is proposed in this paper. This method is applied to the sampled-data representation of a nonlinear system with a constant output time-delay. In particular, the effect of the time-discretization method on key properties of nonlinear control systems, such as equilibrium properties and asymptotic stability, is examined. In addition, 'hybrid' discretization schemes resulting from a combination of the 'scaling and squaring' technique with the Taylor method are also proposed, especially under conditions of very low sampling rates. A performance of the proposed method is evaluated using two nonlinear systems with time-delay output.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.103-106
• /
• 2000

We have studied the magnetic properties in Bi$_2$Sr$_2$CaCu$_2$O$_8$ single crystal with columnar defects using micro Hall-probe array. We found that fold profiles inside sample were similar to the Bean's critical state model from the magnetic hysteresis measurement. In the magnetic relaxation measurement, the normalized relaxation rates were maximum near the center and decreased toward the edge of the sample expect zero gauss. The relaxation rates as a function of the temperature were maximum near the 40K and rapidly decreased both sides of the peak.

• Journal of the Korean Ceramic Society
• /
• v.23 no.3
• /
• pp.62-66
• /
• 1986

Mechanical properties of $Al_2O_3$ based composite ceramics reinforced by SiC whiskers up to 40% by volume we-re investigated. Specimens were hot pressed at $1, 500^{\circ}C$ under 28.5MPa for 30min in Ar atmosphere. Porosities room temperaturefracture toughnesses and flexural strengths up $1, 000^{\circ}C$ were measured. Porosities were increa-sed as the SiC whisker cortent increased. After compensating the effect of porosities that means extrapolated in zero porosities the reinforced composites exhibited increases in flexural strength and fracture toughness as the whi-sker content increased, .

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.49-55
• /
• 2008

Strip bending test has been frequently utilized to measure the mechanical properties of freestanding thin films in substitute for the micro-tensile test. However, in spite of its simplicity and reliability, strip bending test has a few problems, for example, the measurement of strain and the calculation of stress at zero strain. In this study, these problems are precisely reviewed and proved. Upon this review, strip bending tester has been developed, which uses the confocal laser displacement meter to measure the deformed configuration of the specimen and the possibility and limitation of this testing system is carefully investigated including the estimation of uncertainty of the measurement of strain. Finally, to prevent errors and to improve the accuracy of this testing system, the shape of the specimen has been carefully studied and is proposed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.115-118
• /
• 2003

The sensor at liquid nitrogen temperature showed the increase of electrical resistance by applying magnetic field. Actually, the voltage drop across the sensor was changed from zero to a value more than $100\;{\mu}V$ by the applied magnetic field. The change of electrical resistance depended on magnetic field. The sensitivity of this sensor was $2.9\;{\Omega}/T$. The sensing limit was about $1.5{\times}10^{-5}\;T$. The increase of electrical resistance by the magnetic field was ascribed to a modification of the Josephson junctions due to the penetrating magnetic flux into the superconducting material. Considering the observed properties of the superconductor with trapped magnetic flux, a magnetic sensor was fabricated to detect simultaneously both the intensity and the direction of the magnetic field.

• Journal of Surface Science and Engineering
• /
• v.27 no.3
• /
• pp.149-157
• /
• 1994

The formation of spangles on a hot dip galvanized sheet steel by spray cooling the molten zinc coating with air, water and 2.0wt% $NH_4H_2PO_4$ solution has been studied performing laboratory experiments, and their coating properties have been evaluated. Minimized spangles were easily formed by mist spraying the solution for 1 second at the low nozzle spray pressure onto the molten zinc at 420~$422^{\circ}C$ because the solute $NH_4H_2PO_4$ in the sprayed solution imparted a highly rapid cooling effect to the coating through its endothermic de-composition reactions and because the decomposed products acted as numerous nucleation sites for the mini-mized spangles on the coating. Good surface appearances sand sound coating properties were obtained on this coating. Only regular spangles were formed on the coating by the forced convective air cooling. At the high nozzle spray pressure, zero spangles were formed on the coating by the pure water spray cooling. However, the coating had a dull and rough surface with craters sand cracks.