• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.1 s.256
• /
• pp.62-69
• /
• 2007

Micromanipulator is a device that manipulates an object with high precision. Generally, a parallel-type robot has inherently higher precision than a serial-type robot. In most cases, the use of flexure hinge mechanisms is the most appropriate approach to micromanipulators. The micromanipulator is basically required that have high natural frequency and sufficient workspace. However, previous designs are hard to satisfy the required workspace and natural frequency, simultaneously, because the previous micromanipulators are coupled designs. Therefore, this paper suggests a new design parameter as displacement amplifier and new design procedure based on semi-coupled design in axiomatic design. As a consequence the spatial 3-DOF micromanipulator which is chosen as an exemplary device has natural frequency of 500Hz and workspace of $-0.5^{\circ}{\sim}0.5^{\circ}$. To investigate the effectiveness of the displacement amplifier, simulation and experiment are performed.

• The KIPS Transactions:PartB
• /
• v.12B no.5 s.101
• /
• pp.535-542
• /
• 2005

Amplified Collaboration Environment(ACE) is a display-rich project room that enables distributed teams to intensively work together to solve a complex problem. This paper presents reviews of some most important shared workspace models in real-time collaboration systems. It then describes a set of iterative design studies of evaluation the shared workspace for ACEs. The study involved small groups of users in two ACEs performed a collaborative visualization and analysis task while varying the display technology configuration. The goal of this study was to enhance intensive collaborative work in ACEs. The results showed that the participants benefited from the ability to see others' work over the high-resolution shared workspace, which helped enhance group awareness and performance.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.23 no.2
• /
• pp.158-165
• /
• 2013

This paper presents design and workspace analysis of a Korean home service robot. The robot is designed with specific needs of floor-task applications suitable for Korean life style. Shoulder and waist of the robot are adjusted by sliding mechanism to increase the workspace of the robot arms. Manipulators are designed and built and their workspaces are analyzed. Experimental studies of the robot for cleaning the floor are conducted.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.5
• /
• pp.460-470
• /
• 2011

This paper presents a dynamic workspace control method of underwater manipulator considering a floating ROV (Remotely Operated vehicle) motion caused by sea wave. This method is necessary for the underwater work required linear motion control of a manipulator's end-effector mounted on a floating ROV in undersea. In the proposed method, the motion of ROV is modeled as nonlinear first-order differential equation excluded dynamic elements. For online manipulator control achievement, we develop the position tracking method based on sensor data and EKF (Extended Kalman Filter) and the input velocity compensation method. The dynamic workspace control method is established by applying these methods to differential inverse kinematics solution. For verification of the proposed method, experimental data based test of ROV position tracking and simulation of the proposed control method are performed, which is based on the specification of the KORDI deep-sea ROV Hemire.

• Korean Journal of Construction Engineering and Management
• /
• v.5 no.5 s.21
• /
• pp.151-162
• /
• 2004

Current methods for construction site modeling employ large, expensive laser range scanners that produce dense range point clouds of a scene from different perspectives. Days of skilled interpretation and of automatic segmentation may be required to convert the clouds to a finished CAD model. The dynamic nature of the construction environment requires that a real-time local area modeling system be capable of handling a rapidly changing and uncertain work environment. However, in practice, large, simple, and reasonably accurate embodying volumes are adequate feedback to an operator who, for instance, is attempting to place materials in the midst of obstacles with an occluded view. For real-time obstacle avoidance and automated equipment control functions, such volumes also facilitate computational tractability. In this research, a human operator's ability to quickly evaluate and associate objects in a scene is exploited. The operator directs a laser range finder mounted on a pan and tilt unit to collect range points on objects throughout the workspace. These groups of points form sparse range point clouds. These sparse clouds are then used to create geometric primitives for visualization and modeling purposes. Experimental results indicate that these models can be created rapidly and with sufficient accuracy for automated obstacle avoidance and equipment control functions.

• The Journal of Korea Robotics Society
• /
• v.14 no.3
• /
• pp.179-185
• /
• 2019

This paper presents cable-hydraulic driven 3DoF (Degree-of-Freedom) manipulator for cooperative robot with high output/low inertia and enhancing lager workspace of hydraulic manipulator. Hydraulic actuation could be solution to design more higher output manipulator than the one of electric motor actuation due to install actuation source and robot joint separated. In spite of this advantage, the conventional hydraulic driven manipulator using cylinder or vane actuator is not suitable for the candidate of cooperative robot because smaller workspace owing to small RoM (Range of Motion) hydraulic actuator. In this paper, we propose 3DoF manipulator with cable-hydraulic actuation which is more larger ratio of payload-to-weight than the one of conventional cooperative manipulator and larger workspace than the one of existing hydraulic driven manipulator. The performance of proposed manipulator was demonstrated by the experiments for confirming overall workspace task, high payload operation task under worst situation and comparing repeatability between developed manipulator and existed cooperative robots. The results of experiments showed that the appropriate performance of proposed manipulator for cooperative robot.

• Journal of Mechanical Science and Technology
• /
• v.17 no.4
• /
• pp.528-537
• /
• 2003

This paper proposes a 3-PPR planar parallel manipulator, which consists of three active prismatic Joints, three passive prismatic joints, and three passive rotational joints. The analysis of the kinematics and the optimal design of the manipulator are also discussed. The proposed manipulator has the advantages of the closed type of direct kinematics and a void-free workspace with a convex type of borderline. For the kinematic analysis of the proposed manipulator, the direct kinematics, the inverse kinematics, and the inverse Jacobian of the manipulator are derived. After the rotational limits and the workspaces of the manipulator are investigated, the workspace of the manipulator is simulated. In addition, for the optimal design of the manipulator, the performance indices of the manipulator are investigated, and then an optimal design procedure Is carried out using Min-Max theory. Finally. one example using the optimal design is presented.

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.3
• /
• pp.288-296
• /
• 1999

A force-reflecting hand controller can provide the kinesthetic information obtained from a slave manipulator to the operator of a teleoperation system. The goal is to construct a compact hand controller that can provide large workspace and good force-reflecting capability. This paper presents the design and the analysis of a 6-degree-of-freedom force-reflecting hand controller using fivebar parallel mechanism. The forward kinematics of the fivebar parallel mechanism has been calculated in real-time using three pin-joint sensors in addition to six actuator position sensors. A force decomposition approach is used to compute the Jacobian. To evaluate the characteristics of the fivebar parallel mechanism, it has been compared with the other three parallel mechanisms in terms with workspace and manipulability measure. The hand controller using the fivebar parallel mechanism has been constructed and tested to verify the feasibility of the design concept.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.4
• /
• pp.403-413
• /
• 1990

A collision free trajectory control for multiple mobile robots in obstacle-resident workspace is proposed. The proposed method is based on the concept of neural optimization network which has been applied to such problems which are too complex to be handled by traditional analytical methods, and gives good adaptibility for unpredictable environment. In this paper, the positions of the mobile robot are taken as the variables of the neural circuit and the differential equations are derived based on the performance index which is the weighted summation of the functions of the distances between the goal and current position of each robot, between each pair of robots and between the goal and current position of each robot, between each pair of robots and between obstacles and robots. Also is studied the problem of local minimum and of detour in large radius around obstacles, which is caused by inertia of mobile robots. To show the validity of the proposed method an example is illustrated by computer simulation, in which 6 mobile robots with mass and friction traverse in a workspace with 6 obstacles.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.638-642
• /
• 2005

This research develops the robot for the machining work. For machining work(cutting, milling, grilling, etc.), a robot manipulator is constructed by combining a parallel and a serial mechanism to increase stiffness as well as enlarge workspace. Based on the geometric constraints, this paper develops the formulation for inverse/direct kinematics and Jacobian to design and control a robot. Workspace is also analyzed to prove the advantage of the proposed robot.