• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.219-223
• /
• 2005

In this work, a hybrid composite proceeding bearing (HCJB) composed of carbon/phenolic laminated composite bush and steel housing was designed for marine vessels because the composite proceeding bearing reduces the possibility of the seizure problem between the proceeding and bearing. The two components of bearing were assembled by interference fit joining method and a series of durability tests were conducted using the laboratory bench with the lubricants of SAE 30 oil, water, and sea water. That the HCJB was found reliable under the interference fitting loads and environmental temperature change.

• Journal of Communications and Networks
• /
• v.16 no.1
• /
• pp.10-17
• /
• 2014

This work investigates two important performance metrics of underlay cooperative cognitive radio (CR) networks: Interference cumulative distribution function of licensed users and outage probability of unlicensed users. These metrics are thoroughly analyzed in realistic operating conditions such as imperfect fading channel information and strict transmit power constraint, which satisfies interference power constraint and maximum transmit power constraint, over Nakagami-m fading channels. Novel closed-form expressions are derived and subsequently validated extensively through comparisons with respective results from computer simulations. The proposed expressions are rather long but straightforward to handle both analytically and numerically since they are expressed in terms of well known built-in functions. In addition, the offered results provide the following technical insights: i) Channel information imperfection degrades considerably the performance of both unlicensed network in terms of OP and licensed network in terms of interference levels; ii) underlay cooperative CR networks experience the outage saturation phenomenon; iii) the probability that the interference power constraint is satisfied is relatively low and depends significantly on the corresponding fading severity conditions as well as the channel estimation quality; iv) there exists a critical performance trade-off between unlicensed and licensed networks.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.6 no.2
• /
• pp.15-20
• /
• 2004

These days are referred to as 'the times of textile fashion,' owing to the emphasis on textile design in the fashion industry. Accordingly, apparel companies have increased their interests in developing new types of textiles to overcome the limits of style and silhouette. Now the ultra-fashion of textile, a new way of process and design development, is given much more attention. A Moire interference pattern has a longer wavy circle of interference, an effect of intensity interference, than one made by piling more than one reflecting plate or transmitting plate. Till now, Moire interference patterns have been used to confirm scientific theory and to measure the structure of a body or a subject in areas such as physics and medical science. Work has also been done on the Moire interference effects on TV screens said to cause dizziness and eye strain. This study focuses on the new types of textiles by creating the appearance of the Moire phenomena. Contrary to the present usual stationary patterns of textiles, it is a varying pattern according to the different gratings, different angles, piling gratings, and the movements of the human bodies. In the preceding study, we observed Moire fringes formed by overlapping two different or same kinds of gratings such as parallel line gratings, square gratings, conic gratings and semicircular gratings and tried to find a promising possibility of new textiles through the method of clothes design simulation.

• Journal of Computing Science and Engineering
• /
• v.5 no.2
• /
• pp.131-140
• /
• 2011

Different cores typically share the last-level cache in a multi-core processor. Threads running on different cores may interfere with each other. Therefore, the multi-core worst-case execution time (WCET) analyzer must be able to safely and accurately estimate the worst-case inter-thread cache interference. This is not supported by current WCET analysis techniques that manly focus on single thread analysis. This paper presents a novel approach to analyze the worst-case cache interference and bounding the WCET for threads running on multi-core processors with shared L2 instruction caches. We propose to use an interference matrix to model inter-thread interference, on which basis we can calculate the worst-case inter-thread cache interference. Our experiments indicate that the proposed approach can give a worst-case bound less than 1%, as in benchmark fib-call, and an average 16.4% overestimate for threads running on a dual-core processor with shared-L2 cache. Our approach dramatically improves the accuracy of WCET overestimatation by on average 20.0% compared to work.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.4 no.2
• /
• pp.16-23
• /
• 2005

This study is intended to find out the reason of interference phenomenon of a machine tool when it operates for 5-axises working. The researcher made a Virtual Machine which has same figures of the 5 axises machine tool and Virtual Manufacturing System which has both Software factors - controller and NC code data to manipulate the movement characteristics of the machine - and Hardware factors - fixtures, workpiece, tools, holders and so on. With these virtual tools, this study is designed to find out the relation between the movement and the interference or collision, and also intended to verify the simulation and work-processing. In this study, the researcher found out, in case of the vertical 5 axises type, that it has more chances to have interference between the fixture, the workpiece and the main spindle including the tool holder due to the tilting kinetics of the main spindle. In case of the horizontal 5 axises type, on the other hand, the researcher found out that it has more possibility to have the interference between the main spindle and the rotary shaft.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.15 no.3
• /
• pp.111-118
• /
• 2020

We investigate the optimization problem of transmit power control and MMSE Receiver filter for multi access points environment. Previous work showed that increasing the number of access points decreases the transmit power consumption. Accordingly, transmit power control algorithm was developed in such a way that the transmit power is minimized, while each terminal meets Signal to Interference and Noise Ratio Requirement. In this work, we further reduce the transmit power consumption by optimizing the transmit power level and the MMSE receiver filter together. We showed that the proposed joint optimization algorithm satisfies the necessary and sufficient conditions to be standard interference function, which guarantees convergence and minimum transmit power consumption. We observed that the proposed algorithm outperforms the algorithm which only optimizes the transmit power.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.8 no.1
• /
• pp.18-34
• /
• 2014

It is widely believed that cognitive radio (CR) networks have an opportunistic nature and therefore can only support best-effort traffics without quality-of-service (QoS) guarantees. In this paper, we propose a centralized CR network that adopts interference averaging techniques to support QoS guaranteed traffics under interference outage constraints. In such a CR network, a CR user adaptively adjusts its transmit power to compensate for the channel loss, thereby keeping the receive signal power at the CR base station (BS) at a constant level. The closed-form system capacity of such a CR network is analyzed and derived for a single cell with one CR BS and multiple CR users, taking into account various key factors such as interference outage constraints, channel fading, cell radius, and locations of primary users. The accuracy of the theoretical results is validated by Monte Carlo simulations. Numerical and simulation results show promising capacity potential for deploying QoS-guaranteed CR networks in frequency bands with fixed primary receivers. Our work can provide theoretical guidelines for the strategic planning of centralized CR networks.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.13 no.3
• /
• pp.1238-1259
• /
• 2019

Saving energy is a big challenge for Wireless Sensor Networks (WSNs), which becomes even more critical in large-scale WSNs. Most energy waste is communication related, such as collision, overhearing and idle listening, so the schedule-based access which can avoid these wastes is preferred for WSNs. On the other hand, clustering technique is considered as the most promising solution for topology management in WSNs. Hence, providing interference-free clustering is vital for WSNs, especially for large-scale WSNs. However, schedule management in cluster-based networks is never a trivial work, since it requires inter-cluster cooperation. In this paper, we propose a clustering method, called Interference-Free Clustering Protocol (IFCP), to partition a WSN into interference-free clusters, making timeslot management much easier to achieve. Moreover, we model the clustering problem as a multi-objective optimization issue and use non-dominated sorting genetic algorithm II to solve it. Our proposal is finally compared with two adaptive clustering methods, HEED-CSMA and HEED-BMA, demonstrating that it achieves the good performance in terms of delay, packet delivery ratio, and energy consumption.

• Nuclear Engineering and Technology
• /
• v.47 no.6
• /
• pp.729-737
• /
• 2015

Wireless communication technologies, especially smartphones, have become increasingly common. Wireless technology is widely used in general industry and this trend is also expected to grow with the development of wireless technology. However, wireless technology is not currently applied in any domestic operating nuclear power plants (NPPs) because of the highest priority of the safety policy. Wireless technology is required in operating NPPs, however, in order to improve the emergency responses and work efficiency of the operators and maintenance personnel during its operation. The wired telephone network in domestic NPPs can be simply connected to a wireless local area network to use wireless devices. This design change can improve the ability of the operators and personnel to respond to an emergency situation by using important equipment for a safe shutdown. IEEE 802.11 smartphones (Wi-Fi standard), Internet Protocol (IP) phones, personal digital assistant (PDA) for field work, notebooks used with web cameras, and remote site monitoring tablet PCs for on-site testing may be considered as wireless devices that can be used in domestic operating NPPs. Despite its advantages, wireless technology has only been used during the overhaul period in Korean NPPs due to the electromagnetic influence of sensitive equipment and cyber security problems. This paper presents the electromagnetic verification results from major sensitive equipment after using wireless devices in domestic operating NPPs. It also provides a solution for electromagnetic interference/radio frequency interference (EMI/RFI) from portable and fixed wireless devices with a Wi-Fi communication environment within domestic NPPs.

• KIEAE Journal
• /
• v.12 no.6
• /
• pp.77-84
• /
• 2012

The current architectural design of unit modular has been based on 2D of CAD program, so unit modular character which needs unit information management, as a dried-member system, has no effect on design process. The purpose of this study is We have developed a suitable BIM design process, according to various works of construction, then tried to contribute to supply and activation of the urban-life-housing based on unit modular. The BIM modeling process based on unit modular has been in order of unit combination with preparing manual classification, and, it has been constructed, at construction site, from housing foundation to roof finish by Bottom-up method. At a manufacturing factory, it has been produced in order of 1) grouping materials and parts, 2) fabricating unit boxes, and 3) interference examination of unit boxes, and each order has been classified as housing structure, architecture, plumbing process separately. At a construction site, the fabrication has been done in order of, like as a real housing construction scenario, 1) RC foundation work 2) unit module job-site-fabrication work, 3) roof truss work, 4) plumbing and HVAC work, and 5) housing interior finish work. After modeling process, the interference examination on each work of construction has finally completed modeling. The Unit modular utilizing BIM modeling can make easy housing maintenance through systematic control with preparing manual of unit module information, and securing accurate and speedy construction information. And it will promote design credibility and create maximum effect of unit modular construction method, such as construction period reduction and upgrade of construction quality, etc., through the computer simulation as real as construction environment in cyber space, and with the interfering examination.