• The Journal of the Korea institute of electronic communication sciences
• /
• v.4 no.2
• /
• pp.87-92
• /
• 2009

In this paper, we designed and fabricated the active amplification block for the integrated antenna module. The fabricated amplification module have a proper gain and low noise figure in the band of AM/FM band, T-DMB band and GPS band, and show good isolation performance for each band. Manufactured circuits satisfied the gain performance 7 dB in AM band, 11 dB in FM band, 10 dB in T-DMB, and 17 dB in GPS band. The integrated amplification block was realized by 35 mm*35 mm size, and was shown as the same sensitivity performance as compared with a conventional reference antennas.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.193-193
• /
• 2008

In this paper, a MMIC diplexer with a low pass and high pass filter are designed and fabricated using an InGaP/GaAs process. The design of this diplexer is based on its stabilization of the low insertion loss since it is important in the in-building system (IBS). The IBS integrates wire and wireless signal between the cable television (CATV) and the personal communication system. In this design, a dual-mode operation of diplexer is fabricated with the frequency of 0 Hz to 900 MHz and 1.7 GHz to 2.2 GHz for CATV and personal communication. respectively. The topolygy of the designed diplexer is based on the L-C filter. This diplexer fabricated by nanoENS Inc. which is foundry service company, was measured by using the facilities of the Kwangwoon University RFIC center. The fabricated chip size is $1.6\times1.4mm^2$ and it has abroad frequency range from 0 Hz to 2.2 GHz.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.4
• /
• pp.950-954
• /
• 2004

According to the rapid advance of computer and communication techniques, the request of mobile internet services is highly increasing. However, the main obstacles for mobile vector map service environments, are large data volume and narrow wireless bandwidth. Among the many possible solutions, spatial data compression technique may contribute to reduce the load of bandwidth and client response time. This thesis proposes two methods for spatial data compression. The one is relative coordinates transformation method, and the other is client coordinates transformation method. And, this thesis also proposes the system architecture for experiments. The two compression methods could be evaluated the compression effect and the response time.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.6B
• /
• pp.573-587
• /
• 2003

Due to the growth of mobile communication and the popularization of Internet, it is expected that wired and wireless communication network of the next generation will be integrated and flourished with IP-based. There have been a great deal of research efforts to provide mobile IP service onthe existing lower layer. The location update and the paging scheme is one of the most challenging technical issues for this topic. In this thesis, a paging method based on the distance-based location update scheme is proposed for IP network to support mobility in layer 3. The proposed scheme is implemented and verified with the OPNET.

• Journal of Positioning, Navigation, and Timing
• /
• v.12 no.1
• /
• pp.43-49
• /
• 2023

In modern wireless communication systems including beamformers or location-based services (LBS), which employ multiple antenna elements, estimating the number of signals is essential for accurately determining the quality of the communication service. Representative signal number estimation algorithms including the Akaike information criterion (AIC) and minimum description length (MDL) algorithms, which are information theoretical criterion models, determine the number of signals based on a reference value that minimizes each criterion. In general, increasing the number of elements mounted onto the array antenna enhances the performance of estimating the number of signals; however, it increases the computational complexity of the estimation algorithm. In addition, various configurations of array antennas for the increased number of antenna elements should be considered to efficiently utilize them in a limited location. In this paper, we introduce an efficient signal number estimation algorithm based on the beamspace based AIC and MDL techniques that reduce the computational complexity by reducing the dimension of a uniform circular array antenna. Since this algorithm is based on a uniform circular array antenna, it presents the advantages of a circular array antenna. The performance of the proposed signal number estimation algorithm is evaluated through computer simulation examples.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.15 no.12
• /
• pp.4584-4599
• /
• 2021

In IEEE 802.11p-based wireless access in vehicular environments (WAVE) communication systems, channel estimation (CE) is one of the important issues to provide stable communication service. It is hard to apply conventional CE schemes based on data pilot to real systems, because error propagation occurs in high mobility and modulation order environments, resulting in degrading the CE performance. In this paper, we propose one data pilot using multiple receive antennas (ODPM) CE scheme based on the weighted sum using update matrix (WSUM) with time-domain averaging (TDA) to overcome this problem. Within the process of WSUM-TDA in the proposed scheme, the maximum ratio combining (MRC) technique is applied so as to create more accurate one data pilot. Moreover, a new reliability test criterion is proposed as the fashion of utilizing MRC, which makes it possible to apply selective TDA that guarantees performance improvement. In simulation results, the packet error rate (PER) performance of the proposed ODPM is compared with that of conventional CE methods and its superiority is demonstrated.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.3A
• /
• pp.383-390
• /
• 2000

In this paper, an adaptive power control algorithm in the DS/CDMA system is proposed. The currently used transmitter/receiver based on IS-95 and the radio propagation channel under mobile communication environments are modeled. Theses are the key features for the simulation to analyse the performance of power control. the distribution of the received SIR(signal to interference ratio)and the bit error probability are the required parameters for the performance analysis. Furthermore the influence of the power control command error on the above parameters are analyzed. By using the performance analysis of IS-95 and the occurrence of burst errors that is characteristic for wireless channels. the new power control algorithm is proposed. The proposed power control algorithm increases the SIR which results in a better service quality and an enhancement in the system capacity.

• Journal of Positioning, Navigation, and Timing
• /
• v.2 no.1
• /
• pp.91-100
• /
• 2013

This paper introduces an indoor sensor fusion wireless communication device which provides the Location Based Service (LBS) using fire prevention facility. The proposed system can provide information in real time by optimizing the hardware of Wi-Fi technology. The proposed system can be applied to a fire prevention facility (i.e., emergency exit) and provide information such as escape way, emergency exit location, and accident alarm to smart phone users, dedicated terminal holders, or other related organizations including guardians, which makes them respond instantly with lifesaving, emergency mobilization, etc. Also, the proposed system can be used as a composite fire detection sensor node with additional fire and motion detect sensors.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.1181-1184
• /
• 2005

In this paper, we proposed small scale real-time operating system for embedded system. Real-time system is characterized by the severe consequences that result if logical as well as timing correctness properties of system are not met. On real-time system, real-time operating system allows real-time applications to be designed and expanded easily. Functions can be added without requiring major changes to the software. We design small scale real-time operating system for preemptive kernel, and design kernel component such as multitasking, scheduler, task priority, semaphore, inter-task communication, clock tick timer, ISR(Interrupt Service Routine) mechanism has low interrupt latency.

• Electronics and Telecommunications Trends
• /
• v.32 no.5
• /
• pp.85-96
• /
• 2017

The research, design, and development of wireless access technologies using the new 6 to 100GHz band mmWave are actively underway in order to address the frequency shortage problem in the sub-6GHz band and accommodate the 5G technical requirements, such as the increased transmission capacity. Technical elements to efficiently overcome the problems caused by mmWave signal characteristics, support an effective interworking with a conventional communication service, and ensure smooth mobility between mmWave base stations and existing base stations are also being investigated. This paper discusses the technical solutions for an mmWave-based 5G RAN configuration and their considerations under various operational scenarios.