• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.4
• /
• pp.142-151
• /
• 1996

This paper presents a new symmetrical routing architecture for FPGA and an efficient routing algorithm for the architecture. The routing architecture adopts the segmented wires and the improved switch modules. Segmetned wires construct routing channels which pass through the chip in vertical and horizontal directions. To maximize the utility of a track, a track in each switch module can be separated in two part using a programmable switch to route two different net. The proposed routing algorithm finds all assignable tracks for a given net and selects the best track from assignable tracks to minimize the number of programmable switches and the unused portion of the wire segments. In order to stabilize the perfomrance of the algorithm, the routing order is defined by weighted sum of the number of wire segment, the length of wire segmetn, and the number of pin. Experimental results show that routability is improved dramatically and the number of crossing switches are reduced about 40% compared with the previous works.

• ETRI Journal
• /
• v.16 no.2
• /
• pp.1-13
• /
• 1994

We have identified two new features related to the coherent transport in the mesoscopic loop structure of aluminum wire, including the autocorrelation of the conductance fluctuations beyond $B_c$ and fine structure in the low-field magnetoresistance curve in the superconducting transition regime, which, to the best of our knowledge, have not been reported in the literature. Since the electrons in Al have a phase coherence length larger than $1\;{\mu}m$ at or below T = 3K, which is comparable to the dimensions of the structure, the wave nature of the electronic transport has been clearly observed: the universal conductance fluctuations, the Aharonov-Bohm oscillations, and the Altshuler-Aronov-Spivak oscillations. Due to the transition of Al to a superconducting state at T = 1.3 K, the coherent phenomena of Cooper pairs, i.e., the Little-Parks oscillations, have also been observed.

• Tribology and Lubricants
• /
• v.24 no.5
• /
• pp.221-227
• /
• 2008

This paper presents a step-by-step design of noncircular gears. From the diagram of angular velocity ratio of a noncircular gear pair, the pitch curves of the two mating gears are determined, and the perimeter of the pitch curve has been divided into equal-length segments by the number of teeth. A master tooth profile, which is a composite curve of circular arcs that represents involute, has been introduced. A noncircular gear pair has been designed by imposing the master tooth on the divided points of the pitch curve, and a full fillet has been achieved between neighbour teeth. Thus, the whole profile of the noncircular gear is a composite curve of arcs only, and consequently NC codes for wire EDM can be easily generated.

• Magazine of the Korea Concrete Institute
• /
• v.11 no.2
• /
• pp.209-220
• /
• 1999

This paper is aimed to evaluate the effectiveness of flexural toughness of slab panel structures($60{\times}60{\times}10$) reinforced by steel fiber instead of wire mesh. Steel fiber used in this study is double hooked Dramix type fiber. And the fiber length is 60mm, diameter is 0.8mm, Various assessment methods of toughness index are used to estimate the proper effectiveness. In this experimental study, we find that Johnston, JCI-SF4 and EFNARC method are more effective to assess the flexural toughness of slab panels than the others. And the steel fiber is very effective alternative material to reinforce slab panel structures instead of wire mesh. Fiber volume fraction of 0.5~0.75% is more useful than the others in enhancing the post-peak energy absorption and toughness index by Johnston's $I_{5.5}$ assessment method. And the slab panels reinforcing with steel fiber are more resistant to crack propagation than wire mesh reinforcing slabs.

• Structural Engineering and Mechanics
• /
• v.61 no.2
• /
• pp.275-282
• /
• 2017

The Fleck-Hutchinson theory on strain gradient plasticity (SGP), proposed in Adv. Appl Mech 33 (1997) 295, has recently been reformulated by adopting the strategy of decomposing the second order strain presented by Lam et al. in J Mech Pays Solids 51 (2003) 1477. The newly built SGP satisfies the non negativity of plastic dissipation, which is still an outstanding issue in other SGP theories. Furthermore, it explicitly shows how elastic strain gradients and corresponding elastic characteristic length scales come into play in general elastic-plastic loading histories. In this study, the relation between elastic length scales and plastic length scales is investigated by taking wire torsion as an example. It is concluded that the size effects arising when two sets of length scales are of the same order are essentially elastic instead of plastic.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.393-398
• /
• 1999

The main objective of this project is to define the ultimate bond performance of domestic prestressing strands in the precast prestensioned concrete beams. Eight specimens from four different companies were fabricated and tested in this study. Four-point loading tests were performed on the beams of domestic strands with an arbitrary anchorage length. The research has shown, that all seven specimens except one failed in bond are capable of developing their full flexural capacity and the strands within them are fully anchored even with the sudden transfer of frame cutting. Following results are summarized from the tests conducted. 1) All of the specimens are tested at an embedment lengths much shorter than those required by the ACI code, failed in flexure except one failed in bond. 2) It seems that the beam depth can not be an effective variable to estimate the bond length within these sections and length of specimens on this tests. 3) The development length with the stirrup space which are considered for correction factors in the equations of Russel and Paulsgrove, is fully accurate to determine the required length for the beam tested in this research.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.166-169
• /
• 2001

22,000 Ton hydraulic press was developed using wire winding method. The hydraulic press consists of three piece of frame type. The outer layers of yoke-column frame and main cylinder linear were wound with piano wire(1mm${\times}$4mm) under controlled tension and the total length of wound wire was about 450Km. The developed hydraulic press is used for the forming of heat plate with ultra-large size. To obtain large force with relative small apparatus, high pressure of $1,500 Kgf/cm^2$ was supplied to main cylinder through pressure amplification by booster pump. Therefore sealing technique of main cylinder is so crucial that the seals were made of mitre ring type with super-elastic metal. The press total weight is about 150 tons, which is quite light and compact relative to that of conventional hydraulic press.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.1
• /
• pp.8-12
• /
• 2000

The properties variation by deterioration of the 600V grade heat-resistant polyvinyl chloride insulated wire(HIV) was analyzed. The weight variation of the thermal deteriorated HIV was about 42% at 80$0^{\circ}C$ and over. From the analysis result of the metallurgical microscope photographs it shows that the sorface of normal wire showed the elongated structures. However the elongated structures did not appear at $900^{\circ} and over and we could observe that particles were grown. The grown oxidized substances in the thermally deteriorated electric wire were observed by SEM. The CuL, CuK, $CuK_b$, OK and CIK spectra of the thermally deteriorated HIV at $300^{\circ}C$ were uniform regardless of the scanning length, but the spectra of CIK could not found at above $700^{\circ}. At the DTA analysis, the endothermic reactions were occurred around $3006{\circ}C\; and\; 400^{\circ}C$ and the exothermic reactions were occurred around $470^{\circ}, respectively.

• Journal of Welding and Joining
• /
• v.26 no.6
• /
• pp.54-58
• /
• 2008

Laser welding with AZ61 filler wire was carried out to improve formability though reduction of porosity and formation of under fill bead. Optimum welding condition and mechanical properties of butt joint for $400{\times}500{\times}1.3mm$ magnesium sheets were studied. Optimal welding conditions of laser power, welding speed, and defocusing length are 1000W, 3m/min, and 2mm, respectively. Results of tensile test indicated that both tensile strength and elongation of specimens welded with filler wire were improved at room temperature because of reduction of porosity and under-filled bead formation in addition to the precipitation hardening and microstructure refinement by Al-Mn and Mg-Al-Zn precipitates. At elevated temperature of $200{\sim}350^{\circ}C$, fracture location of tensile specimen was shifted from weld metal to base metal, indicating less softening of weld metal than base metal.

• Journal of Powder Materials
• /
• v.23 no.6
• /
• pp.409-413
• /
• 2016

Electrical wire explosion in liquid media is a promising method for producing metallic nanopowders. It is possible to obtain high-purity metallic nanoparticles and uniform-sized nanopowder with excellent dispersion stability using this electrical wire explosion method. In this study, Ni-Fe alloy nanopowders with core-shell structures are fabricated via the electrical explosion of Ni-Fe alloy wires 0.1 mm in diameter and 20 mm in length in de-ionized water. The size and shape of the powders are investigated by field-emission scanning electron microscopy, transmission electron microscopy, and laser particle size analysis. Phase analysis and grain size determination are conducted by X-ray diffraction. The result indicate that a core-shell structured Ni-Fe nanopowder is synthesized with an average particle size of approximately 28 nm, and nanosized Ni core particles are encapsulated by an Fe nanolayer.