• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.3
• /
• pp.60-66
• /
• 2004

The effects of roll diameter, winding time, winding methods and relative humidity on curl In newsprints(46$g/m^2$, 54 $g/m^2$, and 54 $g/m^2$ SNC) are examined. The larger MD curl appears at smaller roll diameter, with the extension of winding time, and at the treat ment of soft nip calendering. The MD curl shows the back side curl at winding methods with top side as outer side(TSO), and the top side curl with top side as inner side(TSI). While the CD curl in newsprints( 46 $g/m^2$, and 54 $g/m^2$ SNC) treated with calender is hardly influenced by the storage times, roll diameter, and winding methods. However the CD curl in newsprint(54 $g/m^2$) gradually increases to a two weeks, and then hold constant regardless of roll diameter and winding methods.. The CD curl shows always the top side curl regardless of winding methods. At high relative humidity, the CD curl largely reduces, but the MD curl is not nearly changed. Especially, the CD curl in news-prints(54 $g/m^2$ SNC) is little affected by the changes of relative humidity.

• Progress in Superconductivity and Cryogenics
• /
• v.12 no.4
• /
• pp.31-35
• /
• 2010

In superconducting magnet applications, winding methods of the superconducting magnet can be classified into a layer winding and a pancake winding. The superconducting magnet using high temperature superconductor (HTS) with rectangular shape is generally fabricated using the pancake winding method. On the other hand, low temperature superconducting (LTS) magnet may be wound by either a pancake winding or a layer winding. Compared with the layer winding, the pancake winding method has a merit of easy replacement of a damaged pancake module, but it also has a demerit of requirement of splicing between each double pancake modules. In this paper, we investigated characteristics of the layer and pancake winding methods using HTS. Six samples were wound out of BSCCO and Coated Conductors (CCs) by two winding methods and their characteristics were experimentally observed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.413-418
• /
• 1996

Alternate pirn winding is more difficult to control than others because starting points of its traverse strokes are changed alternately through the winding operations. However, the alternate pirn winding is ye useful method because the yarn can be hardly broken when it is unwinded from full packaged bobbin. This paper presents kinematic control algorithm for the alternate pirn. The proposed algorithm can decide the values of control variables such as bobbin speed and traverse speed from the given input parameters and constraints by using the kinematic relations of the winding mechanism. The compute simulations and experimental verifications of the developed winding control algorithm are carried out It is concluded that the proposed algorithm is an efficient and reliable alternative to traditional trial and error control methods.

• Journal of Korea Society of Industrial Information Systems
• /
• v.6 no.1
• /
• pp.70-76
• /
• 2001

The disc type driver with Nd-Fe-B magnet is one of the servo drivers, which have many applications in various fields. For efficient and easy, it is desirable to be small and thin in its size. However, the driver which uses a conventional wire reel is very difficult to be reduced in its volume. one of alternatives to achieve the above goal is the thick film multilayer winding. The winding method will significantly reduce the total volume of the driver. Therefor this paper proposed the thick film multilayer winding methods and consists of parts: design manufactures, properties and applications.

• Progress in Superconductivity and Cryogenics
• /
• v.5 no.1
• /
• pp.66-70
• /
• 2003

In a HTS transformer, the perpendicular component of magnetic flux density ($B_r$) applied to HTS tapes of pancake windings becomes larger than that of solenoid winding, thereby decreasing the critical current in the HTS tapes. This paper introduces several methods to reduce $B_r$ applied to the HTS tapes in the transformer with double pancake windings by changing winding arrangements and the relative permeability of flux diverters. We have conducted a winding design for a single-phase 1MVA 22.9kV/6.6kV HTS transformer. We observed a change of $B_r$ due to a variation of gap-length between the high voltage windings and the low voltage windings, reciprocal arrangement and an increase of the number of the high voltage pancake. We also observed a change of Br on the HTS tapes due to variation of the relative permeability of flux diverters placed between the high voltage winding and the low voltage winding. Finally, we have designed a 1MVA 22.9kV/6.6kV HTS transformer winding using suggested methods and calculated transformer parameters by the 3D finite element method.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.842-843
• /
• 2011

Winding methods of the interior permanent magnet synchronous motor for vehicle traction have two kinds. They are concentrated winding and distributed winding. They have merits and demerits and influence motor performance. Therefore, this paper present designs that concentrated winding and distributed winding motor what they have same capacity. And each motor characteristic was analyzed by finite element analysis.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1104-1107
• /
• 2005

This paper presents a comparison of core losses for the four cases of Switched Reluctance Motors (SRM) with different winding method and switching sequence. With concentrated winding SRM, two kinds of switching sequence are considered for one-phase exciting and two-phase simultaneously exciting driving. With both distributed winding and toroidal winding, two-phase exciting driving is considered. The ratio of calculated core losses to input power is able to be used a guide or reference for deciding the winding method and switching sequence of in the initial design stage of SRM.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.388-390
• /
• 1997

We describe the characteristic of LVI(Low-voltage Impulse) test system and methods to detect the deformation of windings in the power transformers. Any winding deformation will result in a change of capacitance between winding parts and possibly some change in the winding inductance. These changes will then result in a change in the responce to the applied pulse in both the magnitude and period of the resulting oscillations. A results of measured differential method in stead of typical method, the sensitivity is greatly improved by the use of differential methods where the pulse is applied to two identical windings and the response measured with a differential amplifier.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.297-298
• /
• 2006

Water leak for the water-cooled generator stator windings affects seriously the availability and the reliability of power plants. Generally, water absorption test is conducted in the power plant during outage in order to confirm if leak part is in the bars or not. In this paper, it is described that the capacitance of winding bars is measured by using the developed water absorption instrument system and the water absorption of winding bars is evaluated by using the stochastic methods. The good results by proposed diagnosis technique can be got. It is expected that the reliability of diagnosis for water absorption is increased if the proposed methods are applied to evaluate the water absorption of stator winding bars.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.208-211
• /
• 2000

Processing parameters of filament winding were investigated by using design of experiment. To understand 4 main effects(fiber tension, impregnation pressure, processing rate, and temperature) and 3 interactions, $L_{27}(3^{13})$ orthogonal array table was adopted. The used materials were carbon fiber and epoxy resin. Split disk test and short-beam test, which are the general test methods for filament wound composite material, were selected as evaluation methods for a filament would part. The optimal processing parameters for the filament winding were easily found through the analysis of variance of the experimental results.