• Journal of Korea Society of Industrial Information Systems
• /
• v.28 no.6
• /
• pp.21-27
• /
• 2023

Modern naval ships install an Infra-Red Signature Suppression system (IRSS) in their exhaust pipe to reduce infrared signature emitted to the outside. In addition, naval ships are strategic assets with a very long life cycle, so high reliability of the performance of the equipment on board must be guaranteed. Therefore, equipment such as IRSS is evaluated for performance through model testing at the design stage. A variety of measuring instruments are used in IRSS model testing, and the reliability of these instruments must also be guaranteed. In this paper, a study was conducted to evaluate the reliability of measurement equipment used in IRSS model testing. The test equipment and instruments used were a hot gas wind tunnel, pitot tube, digital differential pressure gauge, thermocouple sensor, and digital recorder. As the fan speed of the hot gas wind tunnel increased, the measurement deviation of the flow decreased, and the temperature output of the thermocouple sensor showed differences in response time and stability depending on the method used.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.4 s.148
• /
• pp.431-439
• /
• 2006

Due to the limitation of size of the test section, blockage effects could not be avoided in the model test of yacht sails for common wind tunnels. In this paper, a numerical analysis is performed to investigate the blockage effects on the lift and drag forces measured from wind tunnel experiments for a 30 feet sloop yacht sail. Complex airflows around the jib and main sails including three-dimensional flow separations are calculated for various close-hauled conditions. It is found that the blockage of a wind tunnel changes the flow separation and consequently the lift and drag forces of the sails, especially the main sail, reduce and increase, respectively, due to the blockage effects.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.3 s.246
• /
• pp.278-286
• /
• 2006

Experiments were conducted to estimate the performance of drag force type vertical axis wind turbine with an opening-shutting rotor. It was operated by the difference in drag force generated on both sides of the blades. The rotational speed was measured by a tachometer in a wind tunnel and the tunnel wind speed was measured by using a pilot-static tube and a micro manometer. The performance test for a prototype was accomplished by calculating power, power coefficient, torque coefficient from the measurement of torque and rpm by a dynamometer controller. Various design parameters, such as the number of blades(B), blade aspect ratio(W/R), angle of blades$(\alpha)$ and drag coefficient acting on a blade, were considered for optimal conditions. At the experiment of miniature model, maximum efficiency was found at N=15, $\alpha=60^{\circ}$ and W/R=0.32. The measured test variables were power, torque, rotational speed, and wind speeds. The data presented are in the form of power and torque coefficients as a function of tip-speed ratio V/U. Maximum power was found in case of $\Omega=0.33$, when the power and torque coefficient were 0.14 and 0.37 respectively. Comparing model test with prototype test, similarity law by advance ratio for vertical axis wind turbine was confirmed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.10
• /
• pp.899-904
• /
• 2007

During the conceptual design phase of fighter class aircraft, the high speed wind tunnel test with 1/20 scale wing-body-tail model has been conducted to investigate the effects of leading edge flap deflection on the supersonic cruise performance of the aircraft. To select the proper leading edge flap deflection for the wind tunnel test, the aerodynamic characteristics due to various leading edge flap deflections have been analyzed by using corrected supersonic panel method. Based on the results obtained from the experimental and numerical approaches, the effects of leading edge flap deflection have shown to be useful to enhance the supersonic cruise performance of fighter class aircraft.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.7
• /
• pp.575-580
• /
• 2007

During the conceptual design phase of a canard type high maneuverable aircraft, the low speed small scale wind tunnel test was conducted to investigate the high angle-of-attack static stability of the aircraft. In this study, 1/50th scale generic canard-body-wing model was used for the small scale wind tunnel test. For the analysis of static stability including high angle-of-attack nonlinear characteristics, the vertical tail effects were studied due to canard deflections. In addition, the nose chine effects were studied at high angle-of-attack. Based on the results obtained from the experimental study, the configuration change effects for canard type aircraft on high angle-of-attack static stability have been able to analyze.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.9
• /
• pp.816-822
• /
• 2011

In this study, a program has been coded to evaluate propeller thrust rapidly following the effects of propeller shapes and the environmental facts. At this time, Semi-infinite Helical Vortices model is used to predict the induction factor which is introduced by Kawada. This program is based on Wrench's Propeller lifting line theory, and it can predict aerodynamic coefficients such as thrust, power, and efficiency. First of all, this program is compared with test results of NACA reports to verify of the reliability. Secondly, subsonic wind tunnel test has been performed following variations of propeller's rpm and inflow velocities.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.4
• /
• pp.291-297
• /
• 2014

A Design of Experiments(DOE) approach to an experimental study of fuselage drag and stability characteristics of a helicopter configuration was applied to achieve an accuracy improvement in the wind tunnel testing. The impact of blocking the test was assessed by comparing the ANOVA table for the blocked and unblocked cases. For a second-order response model, the role of blocking resulted in a substantial increase in the accuracy of test results. These accuracy improvement could be achieved through randomization, blocking, and replication of the data points i.e. a re-ordering of the test sequence where the data were acquired.

• Wind and Structures
• /
• v.8 no.6
• /
• pp.443-454
• /
• 2005

Wind loading is very important, even dominant in some cases, to large-span single-layer reticulated shells. At present, usually equivalent static methods based on quasi-steady assumption, as the same as the wind-resistant design of low-rise buildings, are used in the structural design. However, it is not easy to estimate a suitable equivalent static wind load so that the effects of fluctuating component of wind on the structural behaviors, especially on structural stability, can be well considered. In this paper, the effects of fluctuating component of wind load on the stability of a single-layer reticulated spherical shell model are investigated based on wind pressure distribution measured simultaneously in the wind tunnel. Several methods used to estimate the equivalent static wind load distribution for equivalent static wind-resistant design are reviewed. A new simple method from the stability point of view is presented to estimate the most unfavorable wind load distribution considering the effects of fluctuating component on the stability of shells. Finally, with comparisive analyses using different methods, the efficiency of the presented method for wind-resistant analysis of single-layer reticulated shells is established.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.275-279
• /
• 2005

The vortex convection and induced flow field behind the KARI 3m x 4m LSWT gust generator was computed by using Computational Fluid Dynamics. For the accurate simulation of vortex convection, inviscid, laminar, Spalart-Allmars k-e and k-w turbulence models were tested with the NAL gust generator configuration and Spalart-Allmaras turbulence model was selected for the prediction of induced flow field behind the KARI LSWT gust generator. The wind tunnel test was also carried out at KARI LSWT and the results were compared with CFD prediction.

• International Journal of Aerospace System Engineering
• /
• v.3 no.2
• /
• pp.26-30
• /
• 2016

Experimental study on the unsteady aerodynamics analysis and power consumption of a folding wing is accomplished using a wind tunnel testing. A folding wing model is fabricated and actuated using servo motors. The flapping wing consists of an inboard main wing and an outboard folding wing. The aerodynamic forces and consumed powers of the flapping wing are measured by changing the flapping and folding wings inside a low-speed wind tunnel. In order to calculate the aerodynamic forces, the measured forces are modified using static test data. It was found that the effect of the folding wing on the flapping wing's total lift is small but the effect of the folding wing on the total thrust is larger than the main wing. The folding motion requires the extra use of the servo motor. Thus, the amount of the energy consumption increases when both the wings are actuated together. As the flight speed increases, the power consumption of the folding wing decreases which results in energy saving.