• Journal of the Korean Society of Clothing and Textiles
• /
• v.27 no.5
• /
• pp.453-462
• /
• 2003

The pantyhose is a close-fitting garment, and consumers are highly sensitive to any progress made in fitting the garment to their lower body and increasing comfort. However, the pantyhose manufactured in Korea are only one-sized. The purpose of this study is to suggest a sizing system for pantyhose. The results of this study are as follows: 1. As a results of questions regarding the sizing system of pantyhose, 88.2% of people who responded to our questionnaire preferred multi-sized pantyhose. In particular, larger women opposed to thin women expressed some dissatisfaction in the length and the width of the pantyhose. In addition, most of women preferred an indication of the sizing system and the body size of the control dimension (body mass and height). 2. The 13 species of pantyhose that were manufactured abroad are of all sizes, and only one type of pantyhose is one-sized. However, most domestic pantyhose except one, are one-sized. 3. As a result of the experiment, the spandex content in pantyhose was approximately 12∼18%. Moreover, the elongation rate was approximately 200-370%, which differed according to the features of the material. The stretch size of the pantyhose had varies greatly, add has not yet been standardized. 4. The methods for indicating the pantyhose size in this study are the square method and the stair method. The characteristics of the square method are simple, but the coverage is relatively low. The characteristic of the stair method are so complicated that older women have a low preference for this method. However, the coverage rate is high.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.2 no.2
• /
• pp.69-77
• /
• 2009

Small size and low profile antenna for mobile vehicular-top-mounted is needed in satellite communication services such as DBS, Satellite Internet and VSAT. In middle latitudes, the development of an array antenna which has the conformal, low profile and 45 degree beam tilted configuration, and has the high gain with sharp beamwidth, low sidelobe and low loss is required for Ka band satellite communication. In this paper, in order to meet with these performances, an array antenna consisting of the vertical polarized waveguide longitudinal slots based on the leaky-wave mode of traveling wave antenna is proposed. Especially, for the lower sidelobe level the radiation power control using a design method of the different slot width is proposed. An array antenna consisting of 32 leakywave elements is showing 34.4 dBi of gain, 3.6 degree of beamwidth, below than -25 dB of sidelobe level, 43 degree of beam tilt angle in center frequency 20.0 GHz. Feed network designed by waveguide cooperated feed shows good performance of wideband and low loss.

• Journal of Power Electronics
• /
• v.17 no.3
• /
• pp.821-834
• /
• 2017

This paper reports on a single-inductor multiple-output step-up converter with digital control. A systematic analog-to-digital-controller design is explained. The number of digital blocks in the feedback path of the proposed converter has been decreased. The simpler digital pulse-width modulation (DPWM) architecture is then utilized to reduce the power consumption. This architecture has several advantages because counters and a complex digital design are not required. An initially designed unit-delay cell is adopted recursively for the construction of coarse, intermediate, and fine delay blocks. A digital limiter is then designed to allow only useful code for the DPWM. The input voltage is 1.8 V, whereas output voltages are 2 V and 2.2 V. A co-simulation was also conducted utilizing PowerSim and Matlab/Simulink, whereby the 55 nm process was employed in the experimental results to evaluate the performance of the architecture.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.324-327
• /
• 2005

An electrophoretic display using $TiO_2$ particles is the most promising candidate because it offers various advantages such as ink-on-paper appearance, good contrast ratio, wide viewing angle, image stability in the off-state and extremely low power consumption. The core technology of electrophoretic display is the dispersion controlling of $TiO_2$ nano particles in nonaqueous solution. To prepare an ink for electronic paper using electrophoretic properties of $TiO_2$ nano particles, cyclohexane with low dielectric constant and transparency, polyethylene for producing polymer coating layer which reduces apparent gravity of $TiO_2$, and $TiO_2$ powders were mixed together by planetary-mill. The zeta-potential value of $TiO_2$ particles in cyclohexane was measured about -40mV, but was measured over -110mV by dispersant attached to polyethylene-coated $TiO_2$ surface. Prepared electronic ink was filled in cross patterned micro-wall with $200{\mu}m$ in width and $40{\mu}m$ in height on ITO glass designed by photolithography. The response time of electronic paper evaluated by mobility of $TiO_2$ particle between micro-walls was measured 0.067sec, but the drift velocity from reflectance wave form during reverse from of electronic ink was measured 0.07cm/sec.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.9
• /
• pp.552-558
• /
• 2016

Goethite, ${\alpha}$-FeOOH have various applications such as absorbent, pigment and source for magnetic materials. Goethite particles were synthesized in a two step process, where $Fe(OH)_2$ were synthesized in nitrogen atmosphere using $FeSO_4$ as a raw material in the first process, and after that acicular goethite particles were obtained in an air oxidation process of $Fe(OH)_2$ in highly alkaline aqueous solution. Their phase and microstructure were investigated with XRD and FE-SEM. It was found that the morphology of goethite and the ratio of length-to-width (aspect ratio) of acicular goethite are dependent on the some factors such as R value ($OH^-/Fe^{2+}$), air flow rate and pH conditions. In particular, R value has the strongest influence on the synthesized goethite morphology. It is considered that the optimal value R is 4.5 because X-ray diffraction peaks of goethite have the highest intensity at that value. Morphology of goethite particles was controlled by air flow rates, showing that their size and aspect ratio are getting smaller and decrease, respectively as air flow rate increases. The largest goethite particle obtained is about 1,500 nm in length and 150 nm in diameter.

• Korean Journal of Applied Biomechanics
• /
• v.20 no.4
• /
• pp.373-380
• /
• 2010

The purpose of this study was to evaluate the effect of balance training on gait stability. The study population included 17 male high school students who were divided into 3 groups, each of which underwent one of the following types of balance-training programs for 8 weeks: 1 foot standing on cushion foam, trunk muscle training, and inverted body position training. 0, 4, and 8 weeks, the following experiment was performed: The participants were asked to close their eyes and take 17 steps; the stability of forward and sideward movement was determined, and the direction linearity was measured. The results revealed that all the training programs caused a decrease in stride deviation and an increase in the and the stride length, thereby improving the stability of forward movement. All the programs decreased the variation in step width and were thus also effective in improving the stability of sideward movement. The inverted body position training program was considered very effective because the cross point appeared on post hoc graphic analysis after 4 weeks, and the deviation length for 10 m was low, i.e., below 4 cm. All the programs were effective with respect to direction linearity because they decreased the deviation in direction widths. The results indicate that whole-body neurocontrol training is more effective than simple muscle training and local focused balance training, although this neurocontrol training-in the form of inverted body position training-required a longer training period than did the other programs.

• Journal of Korea Soil Environment Society
• /
• v.3 no.1
• /
• pp.21-30
• /
• 1998

The purpose of this study is to assess contaminant transfer and environmental impacts to the surroundings by inadequate control of USTs. Several methodologies can be used to approach for the site assessment depending on the appearance of contaminants on the site and their types. In this case study, randomized and/or triangle matrix techniques were used. As a result, the composition of materials in tank station were appeared in several state. From 1 to 1.5m depth, the soil was composed of reclaimed soils. And 1.8-3.5m depth, silty sand was appeared and about 4m, weathered soil was appeared. Based on the preliminary and actual site investigation by DPT methodologies on the width and depth of the site with analysis of BTEX and TPH, the contamination was found in this tank station and already distributed near areas. Finally, it was found that the hydroflow differences during the season affects the area and depth of contamination.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.365-365
• /
• 2010

Similar to the superhydrophobic surfaces of lotus leaf, water strider leg is attributed to hierarchical structure of micro pillar and nano-hair coated with low surface energy materials, by which water strider can run and even jump on the water surface. In order to mimick its leg, many effort, especially, on the fabrication of nanohairs has been made using several methods such as a capillarity-driven molding and lithography using poly(urethane acrylate)(PUA). However most of those effort was not so effective to create the similar structure due to its difficulty in the fabrication of nanoscale hairy structures with hydrophobic surface. In this study, we have selected a low surface energy polymeric material of polytetrafluoroethylene (PTFE, or Teflon) assisted with surface modification of CF4 plasma treatment followed by hydrophobic surface coating with pre-cursor of hexamethyldisiloxane (HMDSO) using a plasma enhanced chemical vapor deposition (PE-CVD). It was found that the plasma energy and duration of CF4 treatment on PTFE polymer could control the aspect ratio of nano-hairy structure, which varying with high aspect ratio of more than 20 to 1, or height of over 1000nm but width of 50nm in average. The water contact angle on pristine PTFE surface was measured as approximately $115^{\circ}$. With nanostructures by CF4 plasma treatment and hydrophobic coating of HMDSO film, we made a superhydrophobic nano-hair structure with the wetting angle of over $160^{\circ}C$. This novel fabrication method of nanohairy structures has been applied not only on 2-D flat substrate but also on 3-D substrates like wire and cylinder, which is similarly mimicked the water strider's leg.

• Parasites, Hosts and Diseases
• /
• v.58 no.4
• /
• pp.431-443
• /
• 2020

Echinostoma mekongi n. sp. (Digenea: Echinostomatidae) is described based on adult flukes collected from humans residing along the Mekong River in Cambodia. Total 256 flukes were collected from the diarrheic stool of 6 echinostome egg positive villagers in Kratie and Takeo Province after praziquantel treatment and purging. Adults of the new species were 9.0-13.1 (av. 11.3) mm in length and 1.3-2.5 (1.9) mm in maximum width and characterized by having a head collar armed with 37 collar spines (dorsal spines arranged in 2 alternative rows), including 5 end group spines. The eggs in feces and worm uterus were 98-132 (117) ㎛ long and 62-90 (75) ㎛ wide. These morphological features closely resembled those of Echinostoma revolutum, E. miyagawai, and several other 37-collar-spined Echinostoma species. However, sequencing of the nuclear ITS (ITS1-5.8S rRNA-ITS2) and 2 mitochondrial genes, cox1 and nad1, revealed unique features distinct from E. revolutum and also from other 37-collar-spined Echinostoma group available in GenBank (E. bolschewense, E. caproni, E. cinetorchis, E. deserticum, E. miyagawai, E. nasincovae, E. novaezealandense, E. paraensei, E. paraulum, E. robustum, E. trivolvis, and Echinostoma sp. IG). Thus, we assigned our flukes as a new species, E. mekongi. The new species revealed marked variation in the morphology of testes (globular or lobulated), and smaller head collar, collar spines, oral and ventral suckers, and cirrus sac compared to E. revolutum and E. miyagawai. Epidemiological studies regarding the geographical distribution and its life history, including the source of human infections, remain to be performed.

• Journal of the Korea Computer Industry Society
• /
• v.2 no.7
• /
• pp.975-982
• /
• 2001

In this study, a solid-state laser system adopting a new real time multi-discharge (RTMD) method in which three flashlamps are turned on consecutively was designed and fabricated to examine the pulse width and the pulse shape of the laser beams depending upon the changes in the lamp rum-on time. That is, this study shows a technology that makes it possible to make various pulse shapes by turning on three flashlamps consecutively on a real-time basis with the aid of a PIC one-chip microprocessor. With this technique, the lamp turn-on delay time can be varied more diversely from 0 to 10 ms and the real-time control is possible with an external keyboard, enabling various pulse shapes. In addition, longer pulses can be more widely used for industrial processing and lots of medical purposes