• Journal of the Society of Naval Architects of Korea
• /
• v.39 no.1
• /
• pp.38-48
• /
• 2002

Theoretical development to generate the directional extreme waves in model basin is established based on wave focusing method. The effects of associated parameters, such as the directional range, frequency width, and center frequency, are investigated in terms of wave focusing efficiency. The two different spectral models of constant wave amplitude and constant wave slope are applied to control the wave characteristics. The wave packets simulated by theory are compared with numerical results based on Boussinesq equation and FEM. Both controls of direction and frequency spectrum are essential to focus directional waves effectively. It is noticed that wave focusing ability depends on the frequency bandwidth of spectrum rather than center frequency, and both spectral models with same parameters result in the equivalent efficiency of wave focusing.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.107-112
• /
• 2002

Ferritic stainless steels would be the most important alloys under the chloride environment. They are a cheaper alternative to austenitic stainless steels [1]. The present study is related to gas tungsten arc welding (GTAW) characteristics of Type 444 stainless steels. The heat of welding leads to grain coarsening in the HAZ and in the weld metal of ferritic stainless steels because they solidify directly from the liquid to the ferritc phase without any intermediate phase transformation. It is therefore recommended that these alloys be welded with a low heat input and at high welding speeds. Attempts to improve weldability were made by using of direct current straight polarity (DCSP) and pulsed current GTAW processes in this study. Measuring weld bead, grain size and Erichsen test were performed and the effects of heat input, pulse frequency on the weld metal and HAZ were studied. The main results were obtained as followings: decreasing heat input was effective to control the width of weld both in DCSP welding and in pulsed current welding; pulsed current welding was found to refine the grain size effectively and the finest grain size was found at the frequency of 150Hz in pulsed current welding; it was found that decreasing heat input also refine the HAZs effectively and the frequency had no different effect on HAZ at the same heat input; the ductility could be improved effectively in pulsed current welding.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.699-702
• /
• 2000

The automation and control of robotic welding process is a very complex assignment because the system is affected by a number of variables which are very difficult to determine or predict in practice. Not only the optimization of the robotic welding process is considered from the point of view of the time and the cost of manufacturing. as well as quality of the weldment. the human factors of the production and many other factors must taken into consideration. hi order to determine the optimal parameters of robotic welding process, it is necessary to build a computer model representing all parameters influencing the welding process as well as the mutual dependence between them. This paper presents an approach to modeling the robotic welding process in which all parameters affecting the welding process are included using a neural network. A detailed analysis of the simulation results has been carried out to evaluate the proposed neural network model.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.984-999
• /
• 2010

A long-term field demonstration experiment of selected stabilization method to reduce the heavy metal mobility in farmland soil contaminated by heavy metals around abandoned mine site was conducted. Field demonstration experiments were established on the contaminated farmland with the wooden plate(thickness=1cm) which dimension were width=200cm, Length=200cm, height=80cm and filled with treated soil, which was mixed with lime stone and steel refining slag except on control plot. Soil samples in the plots were collected and analyzed during the experiment period(2008. 2~2008. 8) after the installation of the plots. Field demonstration experiments results showed that the application ratio of lime stone 5% was effective for immobilizing heavy metal components in contaminated farmland soil.

• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.2
• /
• pp.38.1-38.1
• /
• 2016

TRAO has been newly equipped with a multi-beam receiver system, 16 pixel MMIC preamplifiers in a $4{\times}4$ array, a FFT spectrometer, and new control computer systems. In our new receiver systems one can make simultaneous observations with two molecular lines maximum 15 GHz apart with a spectral band width of 60 MHz. Typical system temperatures are about 160 - 200 K at 86 ~ 100 KHz and 400 - 500 K at 115 GHz in the dry weather. The new systems using On-The-Fly mode were found to be very efficient in making quick and sensitive maps of large clouds with a high velocity resolution (~0.04 km/s at 100 GHz). TRAO now calls for proposals for 2016 and 2017 observing season for everybody. In the talk we will introduce the current status of TRAO upgrade and its scientific preliminary results.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2011.05b
• /
• pp.99-104
• /
• 2011

Daylighting system is an alternative to the energy crisis and environment change. And it is possible improvement system of Architectural Space Environment. Accordingly, it is very useful system. Because Daylight Duct System of Daylighting System gives high performance for its price, distribution rate is very high. But Daylighting Duct System is hard to accurate control. Accordingly, it is difficult to maintain continuously Daylight Environment in Interior Spaces. Lighting Diffusion System has been developed that it is Applying the principle of Reflector and prism diffuser for maximize the efficiency of lighting of Daylight Duct Systems through this study. And then compare lighting performance of Existing System and new Lighting Diffusion System through producing a mock-up. Thus, this study was carried out for the purpose of verification for excellence. It is that installed Each Daylighting Duct System for performance evaluation in a laboratory of width 4m, length 10m, height 2.5m. And illuminance was measured at noon on winter solstice(December 22) under clean sky. The actual measurement result was in the following. Newly developed lighting Diffusion system was measured maximum illuminance 399, minimum illuminance 221, average illuminance 141. Synthetically, daylight factor, uniformity factor and illuminance distribution were improved more than existing system. As a result, it was confirmed that was improved lighting Environment in Interior Spaces.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.649-652
• /
• 2015

Previous marking policy for the AF service of TCP traffic in the Diffserv network have no sufficient consideration on the effect of RTT and target rate. In this paper, in order to improve fairness Index by the effect RTT difference of TCP traffic, we propose the modified TSW3CDM(Time Sliding Window Three Color Dynamic Marker) based on average transfer rate estimation and the flow state. The proposed algorithm is dynamic marking policy that do allocate band width in proportion to transmission rate. To evaluate the performance of the proposed algorithm, We accomplished a computer simulation using NS-2. From simulation results, the proposed TSW3CDM algorithm improves fairness index by comparison with TSW3CM.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1552-1555
• /
• 2005

We have studied the inkjet patterning of synthesized aqueous silver nano-sol on interface-controlled ITO glass substrate. Furthermore, we designed the conductive ink for direct inkjet patterning on bare ITO glass substrate. The first, the highly concentrated polymeric dispersant-assisted silver nano sol was prepared by variation of molecular weight and control of initial nucleation and growth of silver nanoparticles. The high concentration of batch-synthesized silver nano sol was possible to 40 wt%. At the same time the particle size of silver nanoparticles was below $10{\sim}20nm$. The second, the synthesized silver nano sol was inkjet - patterned on ITO glass substrate. The connectivity and width of fine line depended largely on the wettability of silver nano sol on ITO glass substrate, which was controlled by surfactant. The relationship was understood by wetting angle. The fine line of silver electrode as fine as $50{\sim}100\;{\mu}m$ was successfully formed on ITO glass substrate. The last, the direct inkjet-patternable silver nano sol on bare ITO glass substrate was designed also.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.12
• /
• pp.1264-1270
• /
• 2004

A fast switching thyristor with a superior trade-off property between the on-state voltage drop and the turn-off time could be fabricated by the proton irradiation method. After making symmetric thyristor dies with a voltage rating of 1,600 V from 350 $\mu$m thickness of 60 $\Omega$ㆍcm NTD-Si wafer and 200 $\mu$m width of n-base drift layer, the local carrier lifetime control by the proton irradiation was performed with help of the HI-13 tandem accelerator in China. The thyristor samples irradiated with 4.7 MeV proton beam showed a superior trade-off relationship of $V_{TM}$ = 1.55 V and $t_{q}$ = 15 $\mu$s attributed to a very narrow layer of short carrier lifetime(～1 $\mu$s) in the middle of its n-base drift region. To explain the small increase of $V_{TM}$ , we will introduce the effect of carrier compensation at the low carrier lifetime region by the diffusion current.ffusion current.t.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.11
• /
• pp.865-869
• /
• 2011

A cantilever-type piezoelectric generator has advantages of simple structure, ease of fabrication and large displacement by transverse vibration of a beam. It is easy to control the natural frequency, and also possible to increase the output power by changing the length, width, and thickness of the generator. In particular, the length increases, the natural frequency sharply decreases, and vice versa. Hence, the natural frequency can widely be controlled by using change in the length of elastic body. In this paper, the generator was designed and fabricated to change natural frequency using the slides of the case. In addition, the generating characteristics were confirmed through finite element analyses and vibration experiment. As a result, the maximum output characteristics could be generated due to resonance phenomenon although any frequency of external force was applied.