• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.37 no.4
• /
• pp.693-703
• /
• 2017

Rover wheel's mobility depends on soil's condition and wheel's design. The purpose of this study is to evaluate the effect of soil conditions, which are Jumunjin sand and Korean lunar soil simulant (KLS-1), on wheel's motion performance. The experiments were performed by using a single wheel testbed with a wheel which grouser height is 15mm on Jumunjin sand and KLS-1, respectively. Also the influence of grouser length to wheel's mobility performance was studied. The experimental results of torque, drawbar pull and sinkage relating to slip ratio were discussed and analyzed to evaluate wheel's motion performance. Results showed wheel moving on KLS-1 has high performance than Jumunjin sand. Wheel's mobility performance was influenced by soil's properties of cohesion and frictional angle. In addition, wheel's performance of drawbar pull and Torque increased with the increasing of grouser length.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.311-312
• /
• 2006

In this paper, steering systems for mobile robot with permanent magnet wheels are discussed. The mobile robot with permanent magnet wheels can have three different types of steering and driving configurations; two-wheels, three-wheels, four-wheels. By a Two-WD(Wheel Driving) system, driving and steering characteristics are controlled by ratio of each wheel speeds. Three-WD system is steered by a front wheel and driven by rear wheels. Four-WD system has better stability than two wheel system. Usually the permanent magnet wheel has nearly none slip. Thus turning radius of the mobile robot with three-WD and four-WD System will be increased and the steering and driving system will be complicated. To solve this problem, two magnet wheels with two dummy wheels are used in this study. fuming radius of the developed mobile robot is small and the structure of the robot is simple. It is possible to move forward, backward, to turn left and right, and to rotate freely with two-WD. This study proved that two-WD system is very suitable fur the mobile robot with permanent magnet wheels.

• The Journal of Korea Robotics Society
• /
• v.18 no.4
• /
• pp.427-435
• /
• 2023

This paper proposes a method of estimating the pose of a mobile robot by using a learning model. When estimating the pose of a mobile robot, wheel encoder and inertial measurement unit (IMU) data are generally utilized. However, depending on the condition of the ground surface, slip occurs due to interaction between the wheel and the floor. In this case, it is hard to predict pose accurately by using only encoder and IMU. Thus, in order to reduce pose error even in such conditions, this paper introduces a pose estimation method based on a learning model using data of the wheel encoder and IMU. As the learning model, long short-term memory (LSTM) network is adopted. The inputs to LSTM are velocity and acceleration data from the wheel encoder and IMU. Outputs from network are corrected linear and angular velocity. Estimated pose is calculated through numerically integrating output velocities. Dataset used as ground truth of learning model is collected in various ground conditions. Experimental results demonstrate that proposed learning model has higher accuracy of pose estimation than extended Kalman filter (EKF) and other learning models using the same data under various ground conditions.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.11
• /
• pp.97-108
• /
• 2016

Lunar rover plays an important role in lunar exploration. Especially, performance of rover wheel related to interaction with lunar soil is of great importance when it comes to optimization of rover's configuration. In this study, in order to investigate the motion performance of lunar rover's wheel on Korean Lunar Soil Simulant (KLS-1), a single wheel testbed was developed and used to carry out a series of experiments with two kinds of wheel with grousers and without grousers which were used to perform the experiments. Wheel traction performance was evaluated by using traction parameters such as drawbar pull, torque and sinkage correlated with slip ratio. The results showed that the single wheel testbed was suitable for evaluation of the performance of wheel and rover wheel with grousers which was likely to have higher traction performance than that without grousers in Korean Lunar soil simulant. The experimental results could be utilized in verification of the optimum wheel design and effectiveness of wheel traction for Korean lunar rover.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.6
• /
• pp.407-413
• /
• 2013

In the conventional towing tank, the ordinary towing carriage has a speed barrier which caused not only by the limitation of the length of towing tank but also the limitation of acceleration. Therefore the length of the towing tank should be decided carefully from the planning stage of the towing tank construction. Consequently the acceleration of the towing carriage should be taken less than 0.06g practically to avoid the slip of the wheel on rail. Due to the increasing demand of the high speed experiments on the development of special novel ship, the requirement of the high speed towing carriage is continuously increased recently. When the minimum measuring time of the towing experiment is prescribed as five seconds, the carriage should be accelerated with higher than 0.12 g to get the speed of 18 m/sec even in the towing tank having a length of 400m in length approximately. This means that the requirement of acceleration is bigger than twice of the ordinary practices of carriage acceleration. In such a condition the exerted total power of motor could not converted to traction force for the acceleration of the carriage without slip. To over come these difficulties a pair of horizontal traction wheels are reinforced to each of the ordinary vertical carrier wheel and appropriate suspension system has been devised for the towing tank of super high speed operation. It is believed that the design of novel suspension system adaptable for the high speed acceleration of towing carriage will play a important role as a reference for the remodeling of the towing tank for high speed experiment.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.6
• /
• pp.731-738
• /
• 2013

This paper describes a fault-tolerant driving control strategy for an independent steer-by-wire system in sixwheel-drive/six-wheel-steering vehicles. An algorithm has been designed to realize vehicle maneuverability that is as close as possible to that of non-faulty vehicles by inducing high slip ratio of the wheel through a faulty steer-by-wire system in order to reduce the lateral tire force, which is resistant to the yaw motion. Considering the transition of the longitudinal tire force of a wheel with a faulty steer-by-wire component, the longitudinal tire forces are optimally distributed to the other wheels. Fault-tolerant driving performance has been investigated via computer simulations. Simulation studies show that the proposed algorithm can significantly improve the maneuverability of a vehicle with a faulty steer-by-wire system as compared to the optimal traction distribution method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.2
• /
• pp.428-436
• /
• 1998

A TCS slip control system improves acceleration capability and steerability on slippery roads through engine torgue and/or brake torque control. This research mainly deals with the engine control algorithm via the adjustment of the engine throttle angle. The following new control strategy is proposed and investigated ; the TCS slip controller whose input is the difference between the desired driving wheel speed corresponding to the optimum slip ratio and the actual speed yields the target engine torque and then estimates the throttle angle based on the engine performance curve. Various simulation and hardware-in-the-loop simulation have been carried out. The results show the proposed strategy may compensate for the inherent nonlinearity between variation of the throttle angle and variation of the engine torque and produce better performance than the previous strategies without the engine map, especially in the high speed region.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.189-190
• /
• 2002

Rolling-sliding friction was investigated for three SBR (styrene-butadiene rubber) specimens including silica-filled, HAF carbon black-filled, and SAF carbon black-filled SBR. When a rubber wheel was rolled against a glass disk, the coefficient of friction varied with the slip ratios. The coefficient of friction for the silica-tilled SBR showed the highest value of the rubber specimens examined under various slip ratios. The contact areas of silica-filled SBR were larger than those of the carbon black-filled SBRs, as indicated the modulus of the silica-filled SBR showing the lowest value. The contact area during rolling-sliding friction was always smaller than those during the static contact. The friction force at the unit contact area for the silica-filled SBR under braking and driving was higher than those of carbon black-filled SBRs.

• Journal of Mechanical Science and Technology
• /
• v.14 no.8
• /
• pp.836-844
• /
• 2000

In this research any abnormal motion of a vehicle is detected by utilizing the difference between the reference and actual yaw velocities as sell as the information on vehicle slip angle and slip angular velocity. This information is then used as a criterion for execution of the yaw moment control. A yaw moment control algorithm based on the brake control is proposed for improving the directional stability of the vehicle. The controller executes brake controls to provide each wheel with adequate brake pressures, which generate the needed yaw moment. It is shown that the proposed yaw moment control logic can provide excellent cornering capabilities even on low friction roads. This active control scheme can prevent a vehicle from behaving abnormally, and can assist normal drivers in coping with dangerous situations as well as experienced drivers.

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.3
• /
• pp.306-313
• /
• 1999

To measure the accurate position of mobile robot, dead-reckoning method using the encoder attached to each wheel is conventionally used, since it is easy to compute and inexpensive to develop. However, that method is useless when slip occurs and error is accumulated with time. This paper proposes a position estimation method using encoder trailer composed of 2 encoders only(ET-2). This method provides accurate position information even when slip occurs, and can reduce accumulated error if we select the proper link lengths of encoder trailer. Experimental results show the performance of ET-2 when slip occurs. Finally, accumulated systematic error from encoder resolution is analyzed in comparison with an existing method with encoder trailer composed of 3 encoders. (As a matter of convenience, we will call the existing encoder trailer ‘ET-3’)