• 한국분말재료학회지
• /
• 제16권5호
• /
• pp.351-357
• /
• 2009

A two-step recovery method was developed to produce copper powders from copper chloride waste solution as byproducts of MoO$_3$ leaching process. The first step consisted of replacing noble copper ions with external Fe$^{3+}$ ions which were formed by dissolving iron scraps in the copper chloride waste solution. The replaced copper ions were subsequently precipitated as copper powders. The second step was cementation of entire solution mixture to separate (pure) copper powders from aqueous solution of iron chloride. Cementation process variables of temperature, time, and added amount of iron scraps were optimized by using design of experiment method and individual effects on yield and efficiency of copper powder recovery were investigated. Copper powders thus obtained from cementation process were further characterized using various analytical tools such as XRD, SEM-EDS and laser diffraction and scattering methods.Cementation process necessitated further purification of recovered copper powders and centrifugal separation method was employed, which successfully yielded copper powders of more than 99% purity and average 1$\sim$2$\mu$m in size.

• Computers and Concrete
• /
• 제11권1호
• /
• pp.63-73
• /
• 2013

In this study, the effect of reducing cement by proportional addition of waste powder rubber on the performance of concrete under impact three-point bending loading were investigated experimentally and numerically. Concrete specimens were prepared by adding 5%, 10% and 20 % of rubber powder as filler to the mix and decreasing the same percentage of cement. For each case, three beams of $50mm{\times}100mm{\times}500mm$ were loaded to failure in a drop-weight impact machine by subjecting them to 20 N weight from 300mm height, while another three similar beams were tested under static load. The bending load-displacement behavior was analyzed for the plain and rubberized specimens, under static and impact loads. A three dimensional finite-element method simulation was also performed by using LUSAS V.14 in order to study the impact load-displacement behavior, and the predictions were validated with the experimental results. It was observed that, despite decreasing the cement content, the proportional addition of powder rubber until 10% could yield enhancements in impact tup, inertial load and bending load.

• Corrosion Science and Technology
• /
• 제23권1호
• /
• pp.54-63
• /
• 2024

This work investigated the influence of concentration and applied potential on the characteristics of zinc powder (purity, apparent density, morphology, particle size distribution, and particle zeta potential) produced by the electrochemical process from waste brass. High-purity zinc powder is obtained using selective leaching of industrial brass waste in acidic, neutral, and alkaline solutions. The free immersion method with and without voltage using linear polarization technique is used. In the electrochemical process, hydrochloric acid HCl in three different concentrations (0.1, 0.2, and 0.3) M is used. The time and the distance between the electrodes are set to be 30 min and 3 cm, respectively. It has been found that the percentage purity is 98%, 96%, and 94% for the acidic, neutral, and alkaline solutions, respectively. In addition, the morphology of zinc powder analyzed by SEM was dendritic and mossy. It has been recorded that the purity of zinc increases with the increase of the concentration and applied potential. The highest value of purity for zinc powder was %98.58 in 1000 mV and 0.3M concentration for graphite cathode.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 추계 학술논문 발표대회
• /
• pp.65-66
• /
• 2012

The cement used in the construction industry of the manufacturing process, large amounts of the greenhouse gas, CO₂ and is currently being studied for cement substitutes that reduce greenhouse gas issue. Therefore, the this study as a replacement for cement industrial by-product of blast furnace slag, red mud, silica fume and alkali-activator, using only inorganic composites without high-temperature calcination process were manufactured. The waste gypsum board micro powder added to compensate for the shrinkage cracks, the compressive strength and flow, and length change characteristics were investigated. Consequently, The setting time was shortened as GB added And liquidity was reduced. GB 2%, 7 days curing the added strength of specimens was the highest. Came out, and change the length of the Plain least.

• 한국건축시공학회지
• /
• 제4권2호
• /
• pp.143-149
• /
• 2004

The recycle of domestic waste concrete is, however, still in an early stage, and it has been only partially being used for the road fillers. As a counter-plan of activating recycled concrete, we have confirmed the hydration possibility of the waste concrete powder from the experiment on recycling the aggregate powder since 2000. Though that study, we have known that the strength is increasing when the baking time is longer, and baking temperature maintain in $700^{\circ}C$. Also, the quality is lowered because of the fine aggregate powder which has a bad influence on flowability & compression strength by adhesion of mortar on the aggregate face. Therefore, mortar and interfacial separation of aggregate are large in proper quality for concrete recycling is expected that affect. The purpose of this study is to investigate effective aggregate separation and to determine the most suitable production method controlling the duration of baking time for recycled cement from the compressive strength, X-ray diffraction and ingredient analysis test.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 가을 학술논문 발표대회
• /
• pp.107-108
• /
• 2021

In the global trend of countries around the world announcing the declaration of carbon neutrality, the development of low-carbon cement in the cement industry can be seen as a very important issue that can determine the future development of the cement industry in the future. Therefore, this study evaluated the strength characteristics of limestone cement paste with limestone powder of CaCO3 and refinery desulfurization waste catalyst of high Al₂O₃ content, and using a Minitab mixture design to optimize a limestone cement content. As a resuls it was confirmed that limestone cement paste with 5-10% of limestone powder and 1.25-2.5% of the waste catalyst exhibits similar compressive strength to that of OPC.

• 한국분말재료학회지
• /
• 제30권6호
• /
• pp.502-508
• /
• 2023

With the increasing demand for electronic products, the amount of multilayer ceramic capacitor (MLCC) waste has also increased. Recycling technology has recently gained attention because it can simultaneously address raw material supply and waste disposal issues. However, research on recovering valuable metals from MLCCs and converting the recovered metals into high-value-added materials remains insufficient. Herein, we describe an electrospinning (E-spinning) process to recover nickel from MLCCs and modulate the morphology of the recovered nickel oxide particles. The nickel oxalate powder was recovered using organic acid leaching and precipitation. Nickel oxide nanoparticles were prepared via heat treatment and ultrasonic milling. A mixture of nickel oxide particles and polyvinylpyrrolidone (PVP) was used as the E-spinning solution. A PVP/NiO nanowire composite was fabricated via E-spinning, and a nickel oxide nanowire with a network structure was manufactured through calcination. The nanowire diameters and morphologies are discussed based on the nickel oxide content in the E-spinning solution.

• 농업과학연구
• /
• 제47권4호
• /
• pp.1021-1027
• /
• 2020

The amount of food waste generated in Republic of Korea has been increasing alongside an increasing population and booming economy as such, research on effective treatment and recycling is required. Food waste recycling is complicated by its inferior characteristics such as high levels of water and concern that its continuous application to farmland can lead to salt accumulation and concomitant damage crops. In the present study, therefore, dehydrated food waste powder (FWP), which contains a large amount of organic matter and nutrients, but which may require additional improvements was mixed in various ratios with organic fertilizers and the mixtures were tested for their effects on the growth of the leaf lettuce. A control was set up with inorganic fertilizers alone while a treatment with only FWP was also included. The mixture of FWP and organic fertilizers produced better leaf lettuce growth in all the treatments than the control and FWP. The fresh weight of the leaf lettuce produced with a mixture containing 60% FWP was 50% higher than that of the control. The results from this study indicate, therefore, that FWP mixed with other organic supplements in appropriate amounts positively impacts crop growth and development.

• 한국지반환경공학회 논문집
• /
• 제12권1호
• /
• pp.35-40
• /
• 2011

제철소에서 용강을 제조할 때에 사용되는 전로(Converter)나 레이들(Ladle) 등의 노체용 내장 내화물로 마그네시아-카본벽돌이 많이 사용되고 있다. 그러나 이렇게 사용되고 있는 마그네시아-카본 벽돌의 경우 교체 이후 전량폐기되고 있다. 이렇게 폐기되는 폐 마그네시아-카본 벽돌을 분쇄하여 활성화재를 이용한 연약지반 및 오염지반의 고화재로 사용함으로써 연약지반 및 오염지반의 고형화를 통하여 연약지반의 강성증가와 함께 오염지반에서 발생하는 중금속 및 기타 유해물질의 용출에 대한 안정화에 영향을 미칠 것으로 판단된다. 본 논문에서는 폐 마그네시아-카본을 이용한 연약지반의 강도 증가에 대한 내용에 대하여 나타내었다.

• 토지주택연구
• /
• 제14권4호
• /
• pp.121-129
• /
• 2023

본 연구에서는 시멘트 클링커 제조에 사용되는 탄산염 광물인 석회석(CaCO₃)을 이산화탄소(CO₂)가 결합되어 있지 않은 탈탄산 원료를 사용하여 제조 공정 중에 발생하는 이산화탄소(CO₂)를 저감하고자 하는 연구로 다양한 산업부산물 중 폐콘크리트에 부착되어 있는 시멘트페이스트를 이용하고자 하였다. 폐콘크리트는 골재에 시멘트페이스트가 부착되어 있는 상태로 일반적인 파·분쇄 방법으로는 효율적으로 분리하지 못하며 원골재 손상없이 시멘트페이스트만을 벗겨내기 위하여 박리·마쇄방법이 유효하다. 박리·마쇄에 영향을 주는 인자로 박리·마쇄시간, 피분쇄물 종류, 피분쇄물양으로 선정하고 실험계획법을 통해 시멘트 크링커 원료로서 탈탄산된 CaO를 함유한 폐콘크리트 미분말 제조를 위한 최적 마쇄 실험 결과, 박리·마쇄시간 7분, 피분쇄물 종류 8mm, 피분쇄물양 0.6이 폐콘크리트 미분말 생산하는데 최적조건인 것을 알 수 있었으며 생산성에 따른 경제성을 고려할 때 피분쇄물의 크기가 크고 양을 많이 할 경우 박리·마쇄시간을 단축할 수 있을 것으로 판단된다.