• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.282-287
• /
• 2001

The CSCM Upwind method and Material Transport Analysis (MTA) have been used to predict the thermal response and ablation rate for non-charring material to be used as thermal protection material (TPM) in KSR-III test rocket nozzle. The thermal boundary conditions such as cold wall heat-transfer rate and recovery enthalpy for MTA code are obtained from the upwind Navier-Stokes solution procedure. The heat transfer rate and temperature variations at rocket nozzle wall were studied with shape change of the nozzle surface as time goes by. The surface recession was severely occurred at nozzle throat and this affected nozzle performance such as thrust coefficient substantially.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.2
• /
• pp.280-287
• /
• 2000

Laboratory measurements were made of wall pressure fluctuations in a separated and reattaching flow over a backward-facing step. An array of 32 microphones along the streamwise direction was utilized. Various statistical properties of pressure fluctuations were scrutinized. The main emphasis was placed on the flow inhomogeneity along the streamwise direction. One point statistics such as the streamwise distribution of rms pressure and autospectra were shown to be generally consistent with other studies. The coherences and wavenumber spectra in the streamwise directions were indicative of the presence of dual modes in pressure; one is the large-scale vortical structure in low frequency and the other is the boundary-layer-like decaying mode in high frequency.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.4
• /
• pp.1071-1082
• /
• 1995

Numerical analyses have been performed to obtain the absorption heat and mass transfer coefficients and the absorption mass flux from a falling film of the LiBr aqueous solution which is cooled by cooling air. Heat flux at the wall is specified in terms of the heat transfer coefficient of cooling air and the cooling air temperature. Effects of operating conditions, such as the heat transfer coefficient, the cooling air temperature, the system pressure and the solution inlet concentration have been investigated in view of the local absorption mass flux and the total mass transfer rate. Effects of film thickness and film Reynolds number on the heat and mass transfer coefficients have been also estimated. Analyses for the constant wall temperature condition have been also carried out to examine the reliability of present numerical method by comparing with previous investigations.

• Aerospace Engineering and Technology
• /
• v.7 no.2
• /
• pp.27-30
• /
• 2008

Wall correction method for wind tunnel test is reviewed and applied to the numerical experimental results obtained at the wind tunnel condition. The corrected lift coefficient agrees well with the reference data generated from the grid having very far boundary However the corrected drag coefficient presents some deviation from the reference data.

• Journal of computational fluids engineering
• /
• v.13 no.3
• /
• pp.28-34
• /
• 2008

In engineering application of large eddy simulation, there are still questions as follows grid dependency on numerical results, the effect of upwind scheme against a calculation instability, appropriate boundary conditions dealing with turbulence fluctuation and the performance of SGS models. In this study, in order to develop the LES to the engineering application, large eddy simulation was carried out to investigate the effect of upwind scheme, turbulent subgrid model and the grid dependancy of the flow around a wall-mounted cube in a channel at Re=40,000 based on cubic height and bulk mean velocity. The computed velocities, turbulence quantities, separation and reattachment length were evaluated compared with the experimental results of R. Matinuzzi and C. Tropea.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.4
• /
• pp.24-31
• /
• 2011

Performance of the asymmetric trapezoidal fin with various upper lateral surface slopes is investigated by using the two-dimensional analytic method. For a fin base boundary condition, convection from the inner fluid to the inner wall, conduction from the inner wall to the fin base and conduction through the fin base are considered. Heat loss and fin efficiency are represented as a function of the fin base thickness, base height, inner fluid convection characteristic number, fin tip length and fin shape factor. One of the results shows that heat loss increases while fin efficiency decreases as the fin shape factor increases.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.13 no.4
• /
• pp.237-245
• /
• 2009

A numerical solution is provided for a jet produced by a flow emerging from a slit at the bottom corner of a quarter plane. The flow is characterized by the Froude number F, based on the net volume flux and the width of the slit. We perform the free-surface flow for various values of F and another parameter corresponding to the position of the vertical wall. A jet with back-flow near the edge of the vertical wall is obtained, and the limiting case is a jet with a stagnation point.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.281-285
• /
• 2005

Viscous solutions of supersonic jet impinging on a flat wall in a confined plenum are simulated using three-dimensional Navier-Stokes solver. A confined plenum was designed for simulating the missile launch and analyzing the behavior of the exhaust plume, which were accompanied by complex flow interactions with shock and boundary layer. Concerns of this paper are to show accurate simulation of internal flow in confined plenum and to demonstrate the jet flow structure when the jet interacts with a small opening on the side. Objectives of this numerical simulation are to understand the effect of changing the plume exit area of the plenum. Pressure and temperature rise at certain position in the plenum are traced and compared with test data.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.6
• /
• pp.1259-1265
• /
• 2013

In wireless environment such as wireless LAN, proper location of wireless LAN AP allows us to take an effective coverage to provide good wireless communication service. To simulate wireless environment, FDTD formulation is introduced and Gaussian pulse injection in grid space is considered to be replaced wireless LAN AP. So structural effect corresponding to location of arbitrary obstacle must be considered, and its received gain is estimated. An obstacle in scattering field should be modeled to be conductor and concrete wall and its diffraction effect for some cross wall is evaluated between transmitter and receiver point.

• The Korean Journal of Rheology
• /
• v.5 no.1
• /
• pp.34-48
• /
• 1993

최근 CAD/CAM의 발전과 더불어 사출성형공정은 여러분야에 폭넓게 응용되고 있 다. 사출성형공정은 크게 충전과정(filling stage), 냉각과정(cooling stage), 보압과정(packing stage)로 나누어 지는데 이중 충전과정은냉각과정과 보압과정에서 나타날 물리적인 현상과 최종 성형품의 기계적 성질에 중요한 영향을 끼치게 된다. 충전과정의 수치 해석 방법은 대 표적으로 control volume method, branching flow method, transient moving boun-dary method로 구분된다. 본 연구에서는 격자의 형태를 양호하게 형성시키고 유동선단의 형태를 개선하기위한 기법인 Spline 곡선을 이용한 선단격자 재구성(frontal remeshing using spline curve)과 수치해석에 소요되는 시간을 줄이기 위하여 벽면경계조건 처리를 위한 선단 유동 장생성(frontal flow field construction for wall boun-dary condition treatment)기법을 개발 하고 transient moving voundary method에 적용시켜 원형 평판과 인장 및 굽힘시편 그리고 두께가 변하는 사각 형상을 가진 캐비터에서의 충전과정을 수치해석하였다. 그결과 압력 분 포, 온도분포, 속도장, 유동선단의 진전형태 등이 기존에 제출된 해석결과와 비교하여 볼 때 만족스러운 수치해석결과를 보였다.