• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.4
• /
• pp.374-383
• /
• 2011

A numerical model based on a mode method coupling beams and a rectangular plate is proposed to estimate radiation characteristics of an edge-clamped rectangular plate. The radiation efficiency and radiation power in the audio frequency range including the critical frequency can be predicted. The proposed model is rather simple and straightforward and gives reliable results comparing to the previous studies. The estimated radiation characteristics are compared to those of the pinned condition plates and also to those based on the formulae proposed by Maidanik. The radiation efficiency of the clamped plate seems a little higher than that of the pinned plate in the frequency range of corner and edge modes. It is explicitly shown that the power as well as efficiency at high frequencies is not influenced by these edge boundary conditions.

• Journal of Mechanical Science and Technology
• /
• v.18 no.12
• /
• pp.2148-2157
• /
• 2004

The paper deals with the vibration and dynamic stability of cantilevered pipes conveying fluid on elastic foundations. The relationship between the eigenvalue branches and corresponding unstable modes associated with the flutter of the pipe is thoroughly investigated. Governing equations of motion are derived from the extended Hamilton's principle, and a numerical scheme using finite element methods is applied to obtain the discretized equations. The critical flow velocity and stability maps of the pipe are obtained for various elastic foundation parameters, mass ratios of the pipe, and structural damping coefficients. Especially critical mass ratios, at which the transference of the eigenvalue branches related to flutter takes place, are precisely determined. Finally, the flutter configuration of the pipe at the critical flow velocities is drawn graphically at every twelfth period to define the order of the quasi-mode of flutter configuration.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.631-636
• /
• 2000

In this paper a transfer method model was introduced in order to analyze critical speeds and vibration modes of a flexible rotor system, whose rotor shaft is cupped into and fitted with a thin-walled cylinder at its end. The computed analysis results were compared with those of the experimental modal test. Both results show good agreement each other. Furthermore the free-run(or run-down) test result for the real rotor system also shows that the proposed transfer matrix method modelling can be successfully applicable to analyzing accurate critical speeds(or natural frequencies) of the rotor system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.3
• /
• pp.318-324
• /
• 2004

The stability of a simply supported straight pipe is investigated. The time dependent flow is assumed to vary harmonically about a constant mean velocity. Stability conditions and dynamic reponses of a governing equation are conducted by use of multiple scale mettled. Parametric resonances and combination resonances are investigated. Stability boundaries are analytically determined. The resulted stability conditions show that instabilities exist when the frequency of flow fluctuation is close to two times the natural frequency or to the sum of any two natural frequencies. In case that the fluctuated flow frequency is close to zero or to the difference of two natural frequencies, however, instabilities are not found up to the first order of perturbation. Stability charts are numerically Presented fir the first two vibration modes.

• Journal of Advanced Marine Engineering and Technology
• /
• v.11 no.1
• /
• pp.63-71
• /
• 1987

The measuring of acoustic intensity has been investigated by many researchers and practicians during the last several decades. But due to the lack of measurement accuracy, they have had no practical use. In recent years, the two microphone acoustic intensity method has been developed by the advancement of FFT analysis technique and the digital data processing equipment. This new method of using two microphones gives informations on the noise source survey and the acoustic power of sound radiation source without the anechoic room. In this paper, theoretical formulae for the two microphone acoustic intensity method and the sound transmission loss are checked. The obtained results for the acoustical enclosure of gas heat pump were compared with the classical field incidence mass law. The surface vibration modes for a panel of enclosure were also estimated.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.3
• /
• pp.356-363
• /
• 2011

Vibrations and noise in electrical machines are directly related to the characteristics of the radial forces on one hand, and mechanical behavior on the other [1, 4]. The characteristics of these forces depend on the air gap flux density, which is also influenced by other factors, such as stator slots and poles, saturation level, winding type, and certain faults. The aim of this work is to investigate the effect of eccentricity and demagnetization faults on electromagnetic noise generated by the external surface of Permanent Magnet Synchronous Machine [PMSM]. For this purpose, an analytical electromagnetic vibroacoustic model is developed. The results confirm the effect of eccentricity and demagnetization fault in generating some low modes radial forces.

• Proceedings of the KIEE Conference
• /
• 2002.04a
• /
• pp.58-60
• /
• 2002

In this paper the bending vibration analysis of stator for a ring type ultrasonic motor is described. Considering the electromechanical coupling effect, the concepts of generalized stress and strain are explained in detail using the generalized piezoelectric equations, which is the relationship between generalized stress and strain, the differential motion equation were derived. The vibration modes and resonance frequencies of the stator were calculated using the finite element code ATILA.

• Journal of Astronomy and Space Sciences
• /
• v.14 no.2
• /
• pp.367-374
• /
• 1997

Slewing maneuver and vibration suppression control of flexible spacecraft model by Lyapunov stability theory are considered. The specific model considered in this paper consists of a rigid hub with an elastic appendage attached to the central hub and tip mass. Attitude control to point and stabilize single axis using reaction wheel type device is tested. To control all flexible modes is so critical to designing an active control law. We therefore considered an direct output feeback control design by using Lyapunov stability theory. It is shown that the ouput feedback control law design with proposed configuration gives satisfactory result in slewing performance and vibration suppression control.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.9
• /
• pp.849-855
• /
• 2010

Damping may change the response characteristics of nonlinear oscillations due to the parametric excitation of a thin cantilever beam. When the natural frequencies of the first bending and torsional modes are of the same order of magnitude, we can observe the one-to-one combination resonance in the perturbation analysis depending on the characteristic parameters. The nonlinear behavior about the combination resonance reveals a chaotic motion depending on the natural frequencies and damping ratio. We can analyze the chaotic dynamics by using the eigenvalue analysis of the perturbed components. In this paper, we derived the equations for autonomous system and solved them to obtain the characteristic equation. The stability analysis was carried out by examining the eigenvalues. Numerical integration gave the physical behavior of each mode for given parameters.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.90-95
• /
• 2000

This study is to choose the most proper model for AGV throughout simulation of behavior of suspension to reduce trial and error because there is no AGV treating heavy weight at harbor loading and unloading at home. Therefore, we estimate the vibration modes of the various suspension applied to AGV, which is over 75 ton included the weight of two containers on 5G using the Matlab, one of the simulation programs