• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.236-237
• /
• 2005

The structural properties of $(Bi,Ce)_4Ti_3O_{12}(BCT)$ thin films with post-annealing temperature were investigated. $(Bi,Ce)_4Ti_3O_{12}(BCT)$ thin films were deposited by RF sputtering method on Pt/Ti/$SiO_2$/Si substrates with optimum deposition condition. The $(Bi,Ce)_4Ti_3O_{12}(BCT)$ thin films was post-annealed at 600$^{\circ}C$, 650$^{\circ}C$, 700$^{\circ}C$, 750$^{\circ}C$, 800$^{\circ}C$ in furnace,respectively. Increasing the post-annealing temperature, the grain size, density and peak intensity of (117) and c-axis orientation were increased. The $(Bi,Ce)_4Ti_3O_{12}(BCT)$ thin films that annealed at 750$^{\circ}C$ exhibited well crystallized phase and had no vacancy and grain was uniform. but there are some secondary phases observed. At this time, the average thickness of $(Bi,Ce)_4Ti_3O_{12}(BCT)$ thin films was 2000 ${\AA}$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.357-360
• /
• 2000

Ferroelectric 0.05PZN-xPZT(90/10)-(0.95-x)PZT(10/90) (x=0.65, 0.85) specimens were fabricated by the mixed-oxide method and cold-pressing method using sol-gel derived PZT(90/10) and PZT(10/90) powders. All specimens show a uniform ferroelectric grain without the presence of the pyrocholre phase. Average grain size increased with an increase in sintering temperature, the value for the x=0.65 specimen sintered at 125$0^{\circ}C$ was 14.4${\mu}{\textrm}{m}$. The dielectric constant and dielectric loss of the x=0.65 specimen sintered at 125$0^{\circ}C$ were 1247, 2.05%, respectively. All specimens showed fairly good temperature and frequency stability of dielectric constant with the range from -2$0^{\circ}C$ to 6$0^{\circ}C$ and 100Hz to 10MHz. The coercive electric field and the remanent polarization of x = 0.65 specimen sintered at 125$0^{\circ}C$ were 8.5 kV/cm and 13 $\mu$C/cm$^2$, respectively.

• Journal of the Korean Magnetics Society
• /
• v.5 no.6
• /
• pp.947-951
• /
• 1995

The electromagnetic interference is prevented by the high magnetic loss of the ferrite. The absorbing property of electromagnetic wave could be improved by the ferrite that has a finer and more uniform microstructure. The thermal decomposition of organic acid salt provided the uniform composition and fine powder. The absorbing properties of electromagnetic wave were evaluated by the relative complex permeability, permittivity, and the attenuation which is calculated from the results of network analyzer. The permeability and permittivity were increased with increase of the density and with decrease of the grain size. The matching thickness could be reduced with increasing sintered temperature. The attenuation of the Cu-Ni-Zn ferrite showed over 20dB when the matching thickness and the matching frequency range were 6.75mm and from 160MHz to 640MHz, respectively.

• Journal of Powder Materials
• /
• v.2 no.1
• /
• pp.29-35
• /
• 1995

In this study the calcined condition and characteristic of Cu-Ni-Zn ferrite powder were investigated. The Cu-Ni-Zn ferrite powder has been synthesized by the thermal decomposition of the organic acid salt. This process did not require a strict pH control and provided the uniform composition and fine powder with about 0.3 $\mu\textrm{m}$. The XRD diffraction pattern of this powder showed about 50% spinel phase. The optimum calcination was found to be done at $700^{\circ}C$ for one hour. After the calcination, the amount of spinel increased to 90%. The distribution of the particle size showed bimodal peaks, one was about 0.5 $\mu\textrm{m}$ and the other was about 20 $\mu\textrm{m}$. The large particles of 20 $\mu\textrm{m}$ were the agglomeration of fine Particles. The mean Particle size of the powder was about 0.4 $\mu\textrm{m}$. The powder was compacted under 100 MPa pressure and sintered at 1100~ $1250^{\circ}C$ for one hour in air. The density of ferrites specimen was a function of the sintering temperature. The higher the temperature, the denser the ferrite. The maximum relative density of the sintered ferrite was about 93% at $1250^{\circ}C$. The grain size of sintered specimen at $1200^{\circ}C$ was 5 $\mu\textrm{m}$ and homogeneous.

• Advances in materials Research
• /
• v.1 no.3
• /
• pp.233-243
• /
• 2012

Thermal reactive diffusion coating of vanadium carbide on DIN 2714 steel substrate was performed in a molten borax bath at $950-1050^{\circ}C$. The coating formed on the surface of the substrate had uniform thickness ($1-12{\mu}m$) all over the surface and the coating layer was hard (2430-2700 HV), dense, smooth and compact. The influence of the kinetics parameters, temperature and time, has been investigated. Vanadium carbide coating was characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDX) and X-ray diffraction analysis (XRD). The corrosion resistance of the coating was evaluated by potentiodynamic polarization in 3.5% NaCl solution. The results obtained showed that decrease of coating microhardness following increasing time and temperature is owing to the coarsening of carbides and coating grain size.

• Journal of the Korean Ceramic Society
• /
• v.30 no.9
• /
• pp.761-767
• /
• 1993

Electrical and mechanical properties of Pb(Mg, Te, Mn, Nb)O3-PZT ceramics are investigated as a function of CeO2 addition (0 to 0.3wt%), and the output characteristics of piezoelectric transformer are also presented. The grain size decreased and the shapes of particles were more uniform with the addition of CeO2. The coercive electric field(9500V/cm), mechanical quality factor (2500) and bend strength (1065kg/$\textrm{cm}^2$) were improved by addition of CeO2 0.2wt%. After repetition of a number of stress cycles, the degradation of k33 was not found in this sample. The voltage step-up ratio (Vdc/Vrms) of piezoelectric ceramic transformer (half wavevoltage doubler, load resistor 100M.ohm) was about 950 in a linear region, its value was relatively higher than other materials.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.565-568
• /
• 2001

We have fabricated $Bi_{3.25}La_{0.75}Ti_{3}O_{12}(BLT)$ thin(200nm) films on the $Pt/Ti/SiO_{2}/Si$ substrates using a MOD(Metalorganic decomposition) method with annealing temperature from $550^{\circ}C$ to $750^{\circ}C$. The structural properties of the films examined by x-ray diffraction. The layered-perovskite phase obtained above $600^{\circ}C$. Scanning electron micrographs showed uniform surface composed of rodlike grains. The grain size increased with increasing annealing temperature. The BLT thin films showed little polarization fatigue test up to $3.5{\times}10^{9}$ bipolar cycling at a 5V and 100kHz.

• Structural Engineering and Mechanics
• /
• v.59 no.3
• /
• pp.475-502
• /
• 2016

Nanobeams are widely used as a structural element for nanodevices and nanomachines. The development of nano-sized machines depends on proper understanding of mechanical behavior of these nano-sized beam elements. Small length scales such as lattice spacing between atoms, surface properties, grain size etc. are need to be considered when applying any classical continuum model. In this study, Eringen's nonlocal elasticity theory is incorporated into classical beam model considering the effects of axial extension and the shear deformation to capture unique static behavior of the nanobeams under continuum mechanics theory. The governing differential equations are obtained for curved beams and solved exactly by using the initial value method. Circular uniform beam with concentrated loads are considered. The displacements, slopes and the stress resultants are obtained analytically. A detailed parametric study is conducted to examine the effect of the nonlocal parameter, mechanical loadings, opening angle, boundary conditions, and slenderness ratio on the static behavior of the nanobeam.

• Journal of Surface Science and Engineering
• /
• v.30 no.3
• /
• pp.183-190
• /
• 1997

Fabrication and crystallization characteristics of yttria($T_2O_3$) stabilized zirconia(YSZ) thin film by sol-gel process were studied. YSZ sol was synthesized with zirconium n-propoxide($Zr(OC_3H_7)_4)$) and yttrium nitrate pentahydrate ($Y(NO_3)_3.5H_2O$). YSZ film was prepared by depositing the polymeric sol on porous $Al_2O_3$ substrate by spin-coating, and the film characteristics were investigated by FRIR, TG-DTA, XRD, DSC, optical microscopy and SEM. The film topology was uniform and cracks were not found. It was found that the annealing temperature and the concentration of stabilizer affect the crystallization of YSZ film. The YSZ film began to crystallize from amorphous to tetragonal phase at 40$0^{\circ}C$, and it was not converted to cubic structure until $1100^{\circ}C$. It seemed that the grains were formed over $700^{\circ}C$and the average grain size was obtained about 0.2$\mu\textrm{m}$.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.10a
• /
• pp.253-258
• /
• 2002

In this study the confining pressure dependancy of internal friction angle of rock materials are discussed based on the results of a series of large triaxial tests under consolidated-drained condition. The rock materials tested are two kinds of grain-size distribution ;one is well graded, the other poorly graded(a uniform distribution). The obtained results shows that the internal friction angle of rock materials decreases more sharply in low stress level than in high stress level, and the test constants A and b in De Mello's failure criterion on rockfill materials are A =0.683∼l.584, b=0.712∼l.015 for the well graded and A=1.145∼l.523, b=0.788∼0.880 for the poorly graded.