• Journal of the Korea Concrete Institute
• /
• v.21 no.3
• /
• pp.291-302
• /
• 2009

A compression lap splice can be calculated longer than a tension lap splice in high strength concrete according to current design codes. New criteria for the compression lap splice including the effects of concrete strength are required for practical purpose of ultra-high strength concrete. Characteristics of compression lap splice have been extensively investigated and main parameters are derived. In addition, an experimental study has been conducted with column specimens in concrete strength of 40 and 60 MPa. The strength of the compression lap splice consists of bond and end bearing and two contributors are combined. Therefore, combined action of bond and end bearing should be assessed. Compared with tension splices, concrete strength significantly affects the strength of compression splices due to short splice length and existence of end bearing. Test results show that the splice strength can be evaluated to be proportional to square root of compressive strength of concrete. The stress states of concrete surrounding spliced bars govern the strengths of bond and end bearing. Because the axial stress of the concrete is relatively high, the splice strength is not dependent on clear spacing. End bearing strength is not affected by splice length and clear spacing and is expressed with a function of the square root of concrete strength. The failure mode of specimens is similar to side-face blowout of pullout test of anchors and the strength of end bearing can be evaluated using the equation of side-face blowout strength. Because the stresses developed by bond in compression splices are nearly identical to those in tension splices, strength increment of compression splices is attributed to end bearing only.

• Journal of the Korea Concrete Institute
• /
• v.22 no.5
• /
• pp.659-666
• /
• 2010

Although the compression splice needs not be longer than the tension slice due to existence of end bearing, current design codes impose a longer compression lap splice than a tension lap splice in high strength concrete. Hence, new criteria for the compression lap splice including the effects of concrete strength need to be sought for economical design involving ultra-high strength concrete. An experimental study has been conducted with column specimens in concrete strength of 80 and 100 MPa. Test results show that the splice strength can be evaluated to be proportional to square root of compressive strength of concrete. Bar stress developed by end bearing is not affected by splice length and is expressed with a function of the square root of concrete strength. Mean value of stresses developed by end bearing is 16.5 square root of $f_{ck}$. The stresses developed by bond in compression splices are nearly identical to those in tension splices and, therefore, strength increment of compression splices is attributed to end bearing only. From regression analysis of 58 tests, a design equation is proposed for compression lap splice in 40 to 100 MPa of compressive strength of concrete. By the proposed equation, the anomaly of lap lengths in tension and compression is got rid of. In addition, the equation has a reliability equivalent to those of the specified strengths of materials.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1994.09a
• /
• pp.259-264
• /
• 1994

The 1986 AASHTO Guide for the Design of Pavement Structures introduced the resilient modulus as a definitive material property to characterize roadbed soil. Although the incorporation of resilient modulus represents a significant acvance in pavement design practice, the test procedure for resilient modulus is complicated and time-consuming. Therefore, it is necessary to develop data base of resilient modulus for the soils frequently encountered; and to develop the reliable correlations between resilient properties and parameters from simple routine tests, In this study, resilient modulus tests were performed on five cohesive soils sampled from in-service subgrades. The stress at 1 percent axial strain in unconfined compression test(su1.0%) was found as a good indicator of the resilient modulus, and unique relationship between Mg and Su1.0% was obtained. A simple chart to estimate the resilient modulus at different levels of confining stress and deviator stress was also developed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.605-612
• /
• 2003

In this study, the performance of the cut-off wall with the specific functional adsorption layers(containing SAC), which are formed in order to block harmful materials such as heavy metal ions contained in leachate (or outflow water) from either waste landfills or exhausted mines, was Investigated by determining experimental data such as hydraulic conductivities, unconfined compression strengths, adsorption capacities. The performance was compare to those of the present cut-off wall materials such as clay, bentonite-mixed soil, and soil-cement.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 1998.10a
• /
• pp.388-394
• /
• 1998

In this study, the influence of soil contaminant on the cement solidification treatment was considered. Unconfined compression strength(UCS) test was carried out for solidificated specimen, Setting time was measured for cement slurry that was mixed with leachate and wastewater. It was appeared that treatment effect were affected by the the kind of soil, organic content, component of pore water and its concentration. And UCS of samples which were cured in the leachate were decrease about l/5. Especially for the marine clay, UCS of samples which were cured in leachate during 180 days were smaller than 90 days cured samples in the case of cement mixing ratio 5%, 10%.

• Journal of the Korean Society of Safety
• /
• v.14 no.4
• /
• pp.135-141
• /
• 1999

This study is an experimental study to investigate the possibility of the utilization of paper ash as the cover, liner in waste disposal landfill and other construction materials. The sample used in these tests was obtained from Daehan paper mill. A series of tests were peformed to evaluate basic properties, compaction, permeability, compressive strength, consolidation, leaching, and CBR of paper ash. In order to investigate the soil engineering properties of paper ash, the test results were compared with those obtained of fly ash. The results of unconfined compression tests show that paper ash had a larger strength than the fly ash. Also, the maximum dry unit weight of paper ash was approximately 59～76.9% less than that of the fly ash. It was found from the results of leaching test that paper ash is classified as non-detrimental general wastes according to the waste management law.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.55 no.2
• /
• pp.65-75
• /
• 2013

In this study, the engineering characteristics of volcanic ash-cement soil mixtures and zeolite-cement soil mixtures are investigated by using unconfined compression test, freezing-thawing test, SEM and XRD analysis. The samples were mixed with volcanic ash from Mt. Baekdusan or porous zeolite, and cement as the ratios of 3.5:1, 4.0:1, 4.5:1, 5.0:1 with and without metakaolin. It is confirmed that compressive strength degraded with increasing of the amount of volcanic ash or zeolite, and increased with addition of metakaolin as a binder. Moreover, test results suggested that the mixtures provided sufficient freezing-thawing resistance. In addition, ettringite as a product of cement hydration was detected by SEM and XRD, and that possibly contributes to the strength of the mixtures.

• Computers and Concrete
• /
• v.19 no.1
• /
• pp.33-39
• /
• 2017

In this study, two types of aggregate were used for making self-compacting concrete. Standard cubic specimens were exposed to different temperatures. Seventy-two standard cylindrical specimens ($150{\times}300mm$) and Seventy-two cubic specimens (150 mm) were tested. Compressive strengths of the manufactured specimens at $23^{\circ}C$ were about 33 MPa to 40 MPa. The variable parameters among the self-compacting concrete specimens were of sand stone type. The specimens were exposed to 23, 100, 200, 400, 600, and $800^{\circ}C$ and their mechanical specifications were controlled. The heated specimens were subjected to the unconfined compression test with a quasi-static loading rate. The corresponding stress-strain curves and modulus of elasticity were compared. The results showed that, at higher temperatures, Scoria aggregate showed less sensitivity than ordinary aggregate. The concrete made with Scoria aggregate exhibited less strain. The heated self-compacting concrete had similar slopes before and after the peak. In fact, increasing heat produced gradual symmetrical stress-strain diagram span.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2003.10a
• /
• pp.183-186
• /
• 2003

This study was conducted to evaluate effects by adding oil to clay soil and influences of remained oil in soil as time elapsed. Unconfined compression test and direct shear test were performed to analyze strength properties of contaminants in clayey soil. As a results of $q_u$ test for kerosene and diesel contaminated clayey soil indicate that were decreased from near 5% oil content rapidly and the declination of strength were blunt as oil content over 10%. The cohesions(c) and internal friction angle(${\psi}$) of kerosene contaminated clayey soil were not varied as quantities of kerosene in clayey soil increased. In the case of diesel contaminated clayey soil, the cohesions(c) were decreased and the internal friction angle(${\psi}$) were increased.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.49-54
• /
• 2000

Several soil parameters can be calculated for results of Piezocone test; sensitivity, soil classification, OCR, undrained shear strength, coefficient of consolidation etc., and used to analysis geotechnical problems. Particularly, the coefficient of consolidation which is related to degree of consolidation varies according to rigidity index(I/sub r/). In this study, rigidity index(I/sub r/) was analyzed by Roy's formula. Trixial tests and unconfined compression tests data in the ten sites was analyzed. In conclusion, rigidity index(I/sub r/) was suggested such as rigidity index(I/sub r/) = 15∼60, average rigidity index value(I/sub r/) of approximately 33 within a country.