• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2008년도 정기총회 및 학술발표대회
• /
• pp.241-244
• /
• 2008

The decomposition of incident and reflected wave on the two-dimensional experimental flume is very important to elucidate the phenomena between waves and coastal structure such as submerged breakwater or rubble-mound breakwater. In generally, two or three point methods are widely used to decompose waves. Even though three point method gives more accurate result, it requires more wave gauge to install than two point method. Sometimes, this causes economic or measurement problems. In this study, therefore, the applicability of two point method was investigated by using Eigenfunction expansion method.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.143-148
• /
• 2004

This paper presents the two modes for maximum power point tracking of the photovoltaic system. The method combines the merits of the two methods consisting of the open circuit method and the three point weight comparison method. The maximum point found by this method is exactly than by the open circuit method. By the simulation results, the actual maximum point can be found that is better than the Perturb and Observe (P&O) method or the three point weight method only one method, especially, in the case of non regular pattern of Power-Voltage (P-V) curve.

• 대한기계학회논문집A
• /
• 제28권4호
• /
• pp.475-480
• /
• 2004

Function approximation is one of the most important and active research fields in design optimization. Accurate function approximations can reduce the repetitive computational effort fur system analysis. So this study presents an enhanced two-point diagonal quadratic approximation method. The proposed method is based on the Two-point Diagonal Quadratic Approximation method. But unlike TDQA, the suggested method has two quadratic terms, the diagonal term and the correction term. Therefore this method overcomes the disadvantage of TDQA when the derivatives of two design points are same signed values. And in the proposed method, both the approximate function and derivative values at two design points are equal to the exact counterparts whether the signs of derivatives at two design points are the same or not. Several numerical examples are presented to show the merits of the proposed method compared to the other forms used in the literature.

• 비파괴검사학회지
• /
• 제21권5호
• /
• pp.532-541
• /
• 2001

재료의 노화에 의한 강도 및 인성 감소치를 정량적으로 평가하는 비파괴적 기법의 개발이 시도되고 있으며 전기비저항법도 그 중의 하나이다. 본 연구에서는 전기비저항법의 열화도 평가에의 적용성을 살펴보기 위해 먼저 6종 10 가지의 비자성 금속을 측정시료로 선택하여 직류 two-point probe법(혹은 2탐침법)으로 전기비저항을 계산한 결과와 비접촉식 와전류 방법으로 전기비저항을 측정한 결과를 서로 비교하였다. 또한, 1Cr-1Mo-0.25V강에 대하여 비파괴적 측정 방법인 four-point probe 방법(혹은 4탐침법)을 사용하여 얻은 결과와 기존의 2탐침법을 사용하여 얻은 결과를 서로 비교하여 현장에서의 4탐침 기술의 적용 가능성을 살펴보았다. 1Cr-1Mo-0.25V강에 대하여 2탐침법으로 구한 비저항 값과 4탐침법으로 구한 비저항 측정값의 차이는 0.6%였다. 따라서 4탐침법을 사용하여 현장에서 금속소재의 열화도의 비파괴적 평가가 가능하다고 사료된다.

• Journal of applied mathematics & informatics
• /
• 제31권5_6호
• /
• pp.733-745
• /
• 2013

In this paper, we first propose a new technique of the functional iterative methods VIM (Variational iteration method) and NHPM (New homotopy perturbation method) for solving two-point boundary value problems, and then we compare their numerical results with those of the finite difference method (FDM).

• Journal of Power Electronics
• /
• 제19권1호
• /
• pp.119-133
• /
• 2019

Although the dual modulation wave method can solve the low-frequency neutral point potential (NPP) fluctuation problem for three-level neutral point clamped converters, it also increases the switching frequency and limits the zero-sequence voltage. That makes it harmful when dealing with the NPP drift problem if the converter suffers from a long dead time or asymmetric loads. By introducing two degrees of freedom (2-DOF), an NPP control based on a search optimization method can demonstrate its ability to cope with the above mentioned two types of NPP problems. However, the amount of calculations for obtaining an optimal 2-DOF is so large that the method cannot be applied to certain industrial applications with an inexpensive digital signal processor. In this paper, a novel optimal 2-DOF-based NPP control is proposed. The relationships between the NPP and the 2-DOF are analyzed and a method for directly determining the optimal 2-DOF is also discussed. Using a direct calculation method, the amount of calculations is significantly reduced. In addition, the proposed method is able to maintain the strongest control ability for the two types of NPP problems. Finally, some experimental results are given to confirm the validity and feasibility of the proposed method.

• Journal of applied mathematics & informatics
• /
• 제26권3_4호
• /
• pp.689-706
• /
• 2008

In this paper, a fifth order numerical method is presented for solving singularly perturbed two point boundary value problems with a boundary layer at one end point. The two point boundary value problem is transformed into general first order ordinary differential equation system. A discrete approximation of a fifth order compact difference scheme is presented for the first order system. An asymptotically equivalent first order equation of the original singularly perturbed two point boundary value problem is obtained from the theory of singular perturbations. It is used in the fifth order compact difference scheme to get a two term recurrence relation and is solved. Several linear and non-linear singular perturbation problems have been solved and the numerical results are presented to support the theory. It is observed that the present method approximates the exact solution very well.

• 대한기계학회논문집A
• /
• 제27권6호
• /
• pp.1041-1049
• /
• 2003

In this paper, a new local two-point approximation method which is based on the exponential intervening variable is proposed. This new algorithm, called the Two-Point Convex Approximation(TPCA), use the function and design sensitivity information from the current and previous design points of the sequential approximate optimization to generate a sequence of convex, separable subproblems. This paper describes the derivation of the parameters associated with the approximation and the numerical solution procedure. In order to show the numerical performance of the proposed method, a sequential approximate optimizer is developed and applied to solve several typical design problems. These optimization results are compared with those of other optimizers. Numerical results obtained from the test examples demonstrate the effectiveness of the proposed method.

• Structural Engineering and Mechanics
• /
• 제65권3호
• /
• pp.263-274
• /
• 2018

In this study, we propose a frequency domain spectral element method (SEM) for the vibration analysis of a multi-span beam subjected to a moving point force. This study is an extension of the authors' previous study for a single-span beam subjected to a moving point force, where the two-element model-based SEM was applied. In this study, each span of a multi-span beam is represented by the Timoshenko beam model and the moving point force is transformed into the frequency domain as a series of each stationary point force distributed on the multi-span beam. The span at which a stationary point force is located is represented by two-element model, but all other spans are represented by one-element models. The vibration responses to a moving point force are obtained by superposing all individual vibration responses generated by each stationary point force. The high accuracy and computational efficiency of the proposed SEM are verified by comparing the solutions by SEM with exact analytical solutions by the integral transform method (ITM) as well as the solutions by the finite element method (FEM).

• 대한산업공학회지
• /
• 제21권3호
• /
• pp.429-439
• /
• 1995

The Interior point method in linear programming is classified into two categories the affine-scaling method and the logarithmic barrier method. In this paper, we integrate those methods and implement them in one shared module. First, we analyze the procedures of two interior point methods and then find a unified formula in finding directions to improve the current solution and conditions to terminate the procedure. Second, we build the shared modules which can be used in each interior point method. Then these modules are experimented in NETLIB problems.