• Tribology and Lubricants
• /
• v.35 no.4
• /
• pp.199-205
• /
• 2019

Two-dimensional materials such as graphene, h-BN, and $MoS_2$ have attracted increased interest as solid lubricant and protective coating layer for nanoscale devices owing to their superior mechanical properties and low friction characteristics. In this work, the frictional properties of single-layer graphene, h-BN, and $MoS_2$ are experimentally investigated under various normal forces using atomic force microscope (AFM) tips with a spherical and flat end, with the aim to gain a better understanding of frictional behaviors. The nonlinear relationship between friction and normal force friction was clearly observed for single-layer graphene, h-BN, $MoS_2$ specimens slid against the spherical and flat AFM tips. The results also indicate that single-layer graphene, h-BN, $MoS_2$ exhibit low frictional properties (e.g., friction coefficient below 0.1 under 70~100 nN normal force). In particular, graphene is found to be superior to h-BN and $MoS_2$ in terms of frictional properties. However, the friction of single-layer graphene, h-BN, $MoS_2$ against the flat tip is larger than that against the spherical tip, which may be attributed to the relatively large adhesion. Furthermore, it is shown that the fluctuation of friction is more significant for the flat tip than the spherical tip. The resutls of this study may be helpful to elucidate the feasibility of using two-dimensional materials as solid lubricant and protective coating layer for nanoscale devices.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.31 no.2
• /
• pp.41-49
• /
• 2019

We approximately obtain heights of cnoidal waves overtopping on a porous breakwater using both the one-layer Boussinesq equations (Vu et al., 2018) and the two-layer Boussinesq equations (Huynh et al., 2017). For cnoidal waves overtopping on a porous breakwater, we find through numerical experiments that the heights of cnoidal waves overtopping on a low-crested breakwater (obtained by the Navier-Stokes equations) are smaller than the heights of waves passing through a high-crested breakwater (obtained by the one-layer Boussinesq equations) and larger than the heights of waves passing through a submerged breakwater (obtained by the two-layer Boussinesq equations). As the cnoidal wave nonlinearity becomes smaller or the porous breakwater width becomes narrower, the heights of transmitting waves obtained by the one-layer and two-layer Boussinesq equations become closer to the height of overtopping waves obtained by the Navier-Stokes equations.

• Progress in Superconductivity and Cryogenics
• /
• v.8 no.4
• /
• pp.8-11
• /
• 2006

High temperature superconducting coated conductor has various buffer structures on Ni-W alloy. We comparatively studied the growth conditions of a multi buffer layer $(CeO_2/YSZ/CeO_2)$ and a single buffer layer$(CeO_2)$ on textured Ni-W alloy tapes. XRD data showed that the qualities of in-plane and out-of-plane textures of the two type buffer structures were good. Also, we investigated the properties of SmBCO superconducting layer that was deposited on the two type buffer structure. The SmBCO superconducting properties on the single and multi buffer structure showed different critical current values and surface morphologies. FWHM of In-plane and out-of-plane textures were $7.4^{\circ},\;5.0^{\circ}$ in the top CeO2 layer of the multi-buffer layers of $CeO_2/YSZ/CeO_2$, and $7.3^{\circ},\;5.1^{\circ}$ in the $CeO_2$ single buffer layer. $1{\mu}m-thick$ SmBCO superconducting layers were deposited on two type buffer layer. $I_c$ of SmBCO deposited on single and multi buffer were 90 A/cm, 150 A/cm and corresponding $J_c$ were $0.9MA/cm^2,\;1.5MA/cm^2$ at 77K in self-field, respectively.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.28B no.11
• /
• pp.852-858
• /
• 1991

An adaptive hierarchical classifier(AHCL) for Korean character recognition using a neural net is designed. This classifier has two neural nets: USACL (Unsupervised Adaptive Classifier) and SACL (Supervised Adaptive Classifier). USACL has the input layer and the output layer. The input layer and the output layer are fully connected. The nodes in the output layer are generated by the unsupervised and nearest neighbor learning rule during learning. SACL has the input layer, the hidden layer and the output layer. The input layer and the hidden layer arefully connected, and the hidden layer and the output layer are partially connected. The nodes in the SACL are generated by the supervised and nearest neighbor learning rule during learning. USACL has pre-attentive effect, which perform partial search instead of full search during SACL classification to enhance processing speed. The input of USACL and SACL is a directional edge feature with a directional receptive field. In order to test the performance of the AHCL, various multi-font printed Hangul characters are used in learning and testing, and its processing its speed and and classification rate are compared with the conventional LVQ(Learning Vector Quantizer) which has the nearest neighbor learning rule.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.4
• /
• pp.857-864
• /
• 2009

This study aimed at developing the two stage and dual filtration system. It has a sand + activated carbon layer above the underdrain system and a sand layer above the middledrain system for pretreatment. When retrofitting an old filter bed or designing a new one, this technology can substitute the existing sand filter bed without requiring a new site. In order to extend the filtering duration, the upper layer of the filter bed consists of the rapid sand filtration with large particles which pre-treats and removes coarse particles and turbidity matters. The middle layer has biological activated carbon(BAC) and granular activated carbon(GAC) to eliminate dissolved organic matters, disinfection by-products precursors etc. The lower layer consists of the sand filtration for the post filtering mode. In this study, a pilot plant of two stage and dual filtration system was operated for 4 months in the S water treatment plant in Kyounggi-Do. The stability of turbidity was maintained below 1NTU. The TOC, THMFP and HAAFP were removed about 90% by two stage and dual filtration system, which is almost 2 times higher than S WTP. From analysis result of HPC along the depth of activated carbon + sand layer at 2nd stage, microorganism was mostly not detected, however, increment of HPC was shown as it becomes deeper. It indicates that growth of microorganism is occurred at activated carbon layer.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.71-76
• /
• 2001

In general, it is known that the wear rate of the abrasive and the removal rate of the metal bond of the grinding wheel should be balanced to maintain the depth of the insulating surface layer to an appropriate level. In order to accomplish, the high quality ELID grinding, therefore, it is necessary to measure the depth of the insulating layer in real-time and then to control the electrolytic conditions to keep the depth to a certain level. In this study, an in-process measurement system of the insulated layer using two gap sensors - a capacitor type and an eddy current type - developed and the change of the status of the insulated layer during ELID grinding is detected. And from the experimental data, we have chosen the best mathematical model to predict the depth of the insulating layer.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.190-196
• /
• 1999

Hot forgeability of STD 61 steel was boronzed in boronizing paste mainly consisted of B4C and Na2B4O7 at various temperatures and times. Microhardness and thickness of boride layers were measured and distributions of B, Si, Cr and V on the cross section of specimen were observed by EPMA line analysis. Microscopic examination and results of EPMA showed that the boride layer consisted of two layers outer layer of FeB and inner layer of Fe2B. Microhardness of these boride layers was in the range of Hv 1800~2300. Thickness of boride layer increased with times and temperatures. Si-rich $\alpha$ layer was formed between boride layer and matrix. Element such as Cr concentration as Cr23(B, C)6 beneath the boride layer.

• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.219-222
• /
• 2001

Nondestructive nonlinear acoustic method in two dimensions is suggested as a useful tool for detecting defects in a composite layer-structured material. Spectrum level changes in fundamental and harmonic frequencies are observed in the presence of a layer type defect compared with in the absence of such a defect. It is proposed in this study that such spectrum changes we due to the mode conversion. The layer type defect makes different normal modes due to different boundary conditions in the thickness direction for the Lamb waves propagating in a layer-structured material. Specifically, the normal mode with the fundamental frequency in the case of the water-layer gap is converted to the normal mode with the second harmonic frequency in the case of the air-layer gap.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.2
• /
• pp.616-623
• /
• 1996

This paper investigates the linear stability of reacting mixing layers with special emphasis on the existence of multiple unstable modes. The governing equations for laminar flows are from two-dimensional compressible boundary-layer equations. The chemistry is a finite rate single step irreversible reaction with Arrhenius kinetics. For the incompressible reacintg mixing layer with variable density. A necessary condition for instability has been derived. The condition requires that the angular momentum, not the vorticity, to have a maximum in the flow domain. New inflectional modes of instability are found to exist in the outer part of the mixing layer. For the compressible reacting mixing layer, supersonic unstable modes may exist in the abscence of a generalized inflection point. The outer modes at high Mach numbers in the reacting mixing layer are continuations of the inflectional modes of low Mach number flows. However, the generalized inflection point is less important at supersonic flows.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05c
• /
• pp.208-211
• /
• 2002

$Bi_2Sr_2CuO_x$(Bi-2201) thin films were fabricated by atomic layer-by-layer deposition using an ion beam sputtering method. 10 wt% and 90 wt% ozone mixed with oxygen were used with ultraviolet light irradiation to assist oxidation. At early stages of the atomic layer by layer deposition, two dimensional epitaxial growth which covers the substrate surface would be suppressed by the stress and strain caused by the lattice misfit, then three dimensional growth takes place. Since Cu element is the most difficult to oxidize, only Sr and Bi react with each other predominantly, and forms a buffer layer on the substrate in an amorphous-like structure, which is changed to $SrBi_2O_4$ by in-situ anneal.