• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.8
• /
• pp.139-145
• /
• 1996

Tapping is one of the most widely used machining operations. There are several methodes of producing external screw threads, e.g. turning, milling with single or multiple cutter, rolling, and grinding, but the methods available for cutting enternal threads are less numerous, and for threads in small holes, tapping is employed almost exclusively. In this study, the tap with the various geometry has been developed in order to tap special workmaterial at considerably higher cutting speed than that of the conventional HSS tap. The experimental tests are run with various cutting speed by using a piezo type tool dynamometer to measure tapping torque. Tapping torque is affected by the design of the tap, which seems to be due to internal friction and shearing of the metal. It is clarified that the process of chip formation strongly depends on rake angle, relief angle, angle of twist.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.11
• /
• pp.1234-1240
• /
• 2004

We studied on the electro-optic characteristics and dynamic stability according to an undesirably defined pretilt angle induced in high step coverage of pixel area for the Twisted Nematic (TN) / Fringe-Field Switching (FFS) mode. In case of the TN mode, LC directors twist reversely near the edges of thin-film-transistor and black matrix where the pretilt angle of the LC is not well defined. Therefore, the voltage-dependent dynamics of the LC in TN mode is unstable and shows the bad electro-optic characteristics. On the other hand, in case of the FFS mode, the LCs are twisted parallel to the bottom substrate by fringe electric field and the electro-optic characteristic is not influenced by the pretilt angle of the LC which is not well defined.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.213-216
• /
• 2006

This paper was a study about noise reduction through flow stabilization in duct using experimental method and numerical analysis at the same time. To determine the fan's type three kinds of fans(axial fan, centrifugal fan, and axial fan with centrifugal type blades) was examined to investigate the suitability for in-line duct. As a result, under the equal number of rotation 2000 RPM, performance of an axial fan with centrifugal type blades was the most superior by 55dBA at 4.3CMM among other fans. After this, analyzed the results of the numerical analysis to find out the optimum design of pitch angle such as $0^{\circ}$, $10^{\circ}$, $15^{\circ}$ and $20^{\circ}$. The intensity of turbulence was low when pitch angle was $15^{\circ}$ and air volume became peak by 5.08 CMM. It was observed that axis component of velocity increased gradually when pitch angle increased from $0^{\circ}$ to $20^{\circ}$, and embodied noise reduction and improvement of air flow rate through flow stabilization.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.479-482
• /
• 2004

We report a method for simultaneous measurements of cell gap, twist angle, birefringence dispersion of liquid crystal (LC) material and alignment directions in filled reflective LC cells. The method is based on spectral measurements of the LC cell reflectivity for three orientations ($0^{\circ},45^{\circ},90^{\circ}$) of the exit polarizer and may be applied for LC cells with low and high gaps.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.122-125
• /
• 1993

The various geometry of tap been developed in order to tap special workmaterial at considerably higher cutting speed than that of the conventional HSS tap. In this paper a piezo type tool dynamomerer is constructed and used to measure the torque. The experimental tests are run with various cutting speed. It is clarified that the process of chip formation strongly depends on rake angle, relief angel, angel of twist.

• Journal of the Optical Society of Korea
• /
• v.15 no.2
• /
• pp.168-173
• /
• 2011

Based on the distinctive characteristics observed in the intensity transmittance of an IPS-LC panel, the previous one-dimensional model is greatly reduced such that only a few data points and their interpolations predict the intensity transmittance of an IPS-LCD with a small error for arbitrary gray levels. Experimental procedure and numerical methods are described in detail.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.290-292
• /
• 2007

A twisted nematic type liquid crystal electro-optic modulator (TN-LC modulator) was developed. The modulator used single polarizer and the reflection on-off ratio was maximized by optimization of twist angle and retardation of liquid crystal cell. The TNLC modulator shows better sensitivity and response time than conventional liquid crystal modulator.

• Korean Journal of Optics and Photonics
• /
• v.22 no.1
• /
• pp.23-29
• /
• 2011

Bistable chiral splay nematic liquid crystal display (BCSN LCD) is a memory type liquid crystal display using splay and $-\pi$ twist states as two stable states. When the cell thickness to pitch (d/p) ratio is 0.25, splay and $-\pi$ twist states have permanent memory time. However, when the transition from $-\pi$ twist state to splay state is caused by a fringe field, pixel regions show that the splay state is not perfect, but rather includes a contribution from the $-\pi$ twist state. In this paper, we propose a reflective BCSN LCD using $-\pi$ twist state in which the two stable states do not coexist. The fabricated reflective BCSN LC cell shows a high contrast ratio of over 30:1 and response times of 950 ms and 450 ms in vertical and fringe field switching, respectively. The proposed cell also shows wide viewing angle characteristics of $180^{\circ}$ in left- and right directions.

• Korean Journal of Applied Biomechanics
• /
• v.19 no.1
• /
• pp.67-75
• /
• 2009

The purpose of this study is to analyze the effects of target position on the bowling motion. Four female high school athletes with more than four years of bowling experiences were recruited to this study. The major results of this study are as follows; When a subject treats the 1st pin, The spin angle of a coxa for the target position is largely kept from the downswing to the backswing peak point. When a subject treats the 7th pin, As the 7th pin exists at the left side for the right shoulder axis of the thrower, the movement of the ball center of the thrower from side to side is the lowest. In addition, the time required and horizontal speed appear the highest in the release section. The slant angle of a shoulder is largely increased as she moves from the backswing peak point to the release section. The twist angle of a shoulder also appears small as a throw motion is made toward the left side. When a subject treats the 10th pin, The spin angle of a shoulder and the twist angle of a body in motion appear the largest in the release section. So, there are the effects of target position on the bowling motion.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.3
• /
• pp.134-137
• /
• 2010

We have proposed a transflective liquid crystal display (LCD) driven by the fringe field using a liquid crystal (LC) with a negative dielectric anisotropy. The device used different twist angles of the liquid crystals (LC) in the transmissive (T) and the reflective (R) regions when voltage is applied. With the optimization of the pixel electrode width and the distance between them, the LC directors in the R- and T-regions can be rotated by about $22.5^{\circ}$ and $45^{\circ}$ on an average, respectively. As a result, a high image quality transflective LCD with a single gap, a single gamma, and a wide viewing angle characteristics in both the R- and T- regions can be realized.