• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.5A
• /
• pp.407-415
• /
• 2010

In Korea, more than 90% of the total number of steel bridges built for 40~70 m span length is a steel box-girder bridge type. A steel box-girder bridge is suitable for long span or curved bridges with outstanding flexural and torsional rigidity as well as good constructability and safety. However, a steel box-girder bridge is uneconomical, requiring many secondary members and workmanship such as stiffeners and ribs requiring welding attachments to flanges or webs. Therefore, in US and Japan, a plate girder bridge, which is relatively cheap and easy to construct is generally used. One type of the plate girder bridge is the two- or three-main girder plate bridge, which is a composite plate girder bridge that minimizes the number of required main girders by increasing the distance between the adjacent girders. Also, for the simplification of girder section, the stiffener which requires attachment to the web is not required. The two-main steel girder plate bridge is a representative type of plate girder bridges, which is suitable for bridges with 10 m effective width and has been developed in the early 1960s in France. To ensure greater safety of two- or three-main girder plate bridges, a larger steel section is used in the bridge domestically than in Europe or Japan. Also, the total number of two- or three-main girder plate bridge constructed in Korea is significantly less than the steel box girder bridge due to a lack of designers' familiarity with more complex design detailing of the bridge compare to that of a steel box girder bridge design. In this study, a new construction method called Turn Over method is proposed to minimize the steel section size used in a two- or three-main girder plate bridge by applying prestressing force to the member using confining concrete section's weight to reduce construction cost. Also, a full scale 20 m Turn Over girder specimen and a Turn Over girder bridge specimen were tested to evaluate constructability and structural safety of the members constructed using Turn Over process.

• Korean Architects
• /
• s.514
• /
• pp.13-13
• /
• 2012

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.11 no.4
• /
• pp.472-483
• /
• 1999

The evaporation heat transfer and pressure drop characteristics for HFC-l34a in flat plate type heat exchangers with enhanced beads were experimentally investigated. Three plate type evaporators with different geometric condition of U-turn area were tested. Mass fluxes were tested over the range of 83kg/$m^2$s to 166kg/$m^2$s, and heat fluxes were varied from 4㎾/$m^2$ to 12㎾/$m^2$. Evaporation temperature was 5$^{\circ}C$ with inlet qualities of 0.1 to 1.0. There was no notable difference in the heat transfer coefficient by geometric variation of U-turn area, but the third plate with cross-ribbed channel at U-turn area was better than others in the evaluation using volume goodness factor comparison. Also, the mixtures of HFC-l34a and PAG oil was tested to determine oil effects on heat transfer and pressure drop. As oil concentration was increased, heat transfer coefficient was increased by 22~48% up to the 3wt.%, but decreased by 14~22% at the 4wt.%. The pressure drop was increased by the maximum of 100% as oil concentration was increased.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.101-105
• /
• 2005

Hemming process, composed of flanging, pre-hemming and main hemming, is the last one of a series of forming processes conducted on the automotive panels, having a great influence on the outward appearance of them. The hem quality can be quantitatively defined by the hemming defects including turn-down, warp and roll-in. However, it is difficult to evaluate and predict the hem quality through the experimental measurement or the numerical calculation since the size of defects is very small. This study is focused on how to simulate in the finite element analysis (FEA) the same conditions as in the experiment. The FEA result on turn-down, that was obtained from a finite element model including the spring element linked to the flanging pad, had a good correlation with the experimental data. It was found that the radius of curvature of the flange deeply affects the final hem quality and therefore high rigidity of forming tools and tight assembling tolerance are highly recommended. An over-stroke of the main hemming punch is also proposed to reduce the turn-down.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.18 no.5
• /
• pp.1-18
• /
• 2019

A short-turn bus is a bus that is operated within a subsection of an existing bus line. Previous studies regarding short-turn buses decided optimal turn-back points for a single bus line rather than a bus network. Also, in-vehicle crowding which has a significant impact on transit convenience was rarely considered. Therefore, this study aimed to develop a methodology to set priorities for the introduction of short-turn buses of bus lines and sections, considering crowding. To achieve this objective, we calculated occupancies and crowding alleviation benefits of existing bus lines overlapping a new short-turn route based on transit card data, before and after the introduction of short-turn strategy. Also, operator and social costs caused by the introduction of short-turn buses were calculated. Those procedures were iterated over bus lines and sections to operate a short-turn service, and a section whose benefit-to-cost ratio (B/C) is the largest in a line was selected to operate a short-turn service in the line. After, priorities of bus lines to introduce short-turn services could be determined based on B/C values, and the optimum total fleet size could be determined when a short-turn strategy is applied in multiple lines.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.3
• /
• pp.50-58
• /
• 2017

TPCLT(Twice Per Cycle Left-turn) operation reduces this left-turn 'spill-over' problem on an as needed basis by servicing the protected left-turn movement as a leading and a lagging left-turn. In this study, to evaluate the effectiveness of TPCLT applied to three-legged signalized intersection in Korea, the analysis was carried out using VISSIM and SSAM model analysis. The study was implemented by three cases which are TPCLT operation, non-TPCLT operation and half-cycle operation using VISSIM program. According to the 9-left-turn volume scenario, total delay and travel times of each case was analyzed by VISSIM program. The study result shows more effective applying TPCLT operaion in the present ~ +50% scenario area at the intersection in terms of total delay.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.11
• /
• pp.9-16
• /
• 2014

The electronic ballast for HID lamps needs high ignition voltage which is consisted of high voltage pulse ignitor. However, In the case of street lamp it is far from a lamp to a ballast, the conventional pulsed high voltage ignitor can not turn on the HID lamps because of reduction of ignition voltage. Therefore, it needs to do the research on a resonant ignition to turn on the HID lamps. However, the resonant circuit which is consisted of LC occurs over current, so the capacity of the ignitor increases. The capacity of the ignitor can be reduced by using the transformer. In this case, the capacitor for resonance is installed to the secondary of the transformer, and the capacitor needs high withstanding voltage. Therefore, it needs to do the research on a resonant ignition to reduce the voltage over the resonant capacitor by dividing the secondary of the transformer.

• Journal of the Society of Naval Architects of Korea
• /
• v.51 no.1
• /
• pp.42-50
• /
• 2014

Lifting lugs are frequently used in shipyard to transportate and turn over blocks. As the shipbuilding technology develops, blocks has become bigger and bigger, and block management technology takes a more important role in shipbuilding to enhance the productivity. For the sake of economic as well as safe design of lug structure, more rigorous analysis is needed. In this study in order to investigate the strength characteristics of two type of lug, that is, D and T type lugs, non-linear strength analysis has been carried out to compare the ultimate strength characteristics of two types of lug varying in-plane and out-of-plane loading directions. Based on the present numerical analysis results, it can be drawn that T type lug is superior to D type lug from view points of ultimate strength and deformation.

• Journal of Korean Society of Steel Construction
• /
• v.25 no.1
• /
• pp.61-70
• /
• 2013

A turn-buckle is capable of adjusting the tensile force by left-hand threads and right-hand threads between tension members. There are different types of turn-buckles according to tension member and connection form but the practical and existing turn-buckles are incapable of measuring the tensile force. A turn-buckle for adjusting and measuring tensile force has therefore been developed. This study shows the ultimate strength and reliability for measurement of the new turn-buckles through finite element analysis of the developed ones. From analytic results of the new turn-buckles which have the measurement limit loads of 100kN, 200kN and 300kN, the ultimate strength is approximately five times stronger than the measurement limit capacity. Additionally, a review of the new turn-buckle, which has the measurement limit load of over 300kN, shows that there is a tendency for the size of turn-buckle to become larger. So the connection devices were designed and the loading test was conducted from the concept that the parallel connection of turn-buckle with 300kN capacity can measure the tensile force of 600kN. The results of parallel loading test show the sufficient possibility. Furthermore, the mock-up test was constructed to investigate the release of initial load and corrosion when the new turn-buckle is installed at the outdoor and exposed to rain and atmosphere.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1547-1549
• /
• 1996

The electrical and optical switching characteristics of gold-doped silicon p-i-n diodes have been investigated. The device shows a dark switching voltage of about 500 V. The switching voltage decreases rapidly when the illumination level is increased. The differential sensitivity of optical gating over linear region is $d(V_{Th}/V_{Tho})/dP_{Ph}$=0.25/uW. The turn-on delay time and the turn-on rise time decrease with increasing optical pulse power. The turn-off delay and the fall time are negligible.