• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.10 s.352
• /
• pp.90-97
• /
• 2006

We report our research work on the millimeter-wave broadband amplifier integrating the shunt peaking technology with the cascode configuration. The millimeter-wave broadband cascode amplifier on MIMIC technology was designed and fabricated using $0.1{\mu}m\;{\Gamma}-gate$ GaAs PHEMT, CPW, and passive library. The fabricated PHEMT has shown a transconductance of 346.3 mS/mm, a current gain cut off frequency ($f_T$) of 113 GHz, and a maximum oscillation frequency ($f_{max}$) of 180 GHz. To prevent oscillation of designed cascode amplifier, a parallel resistor and capacitor were connected to drain of common-gate device. For expansion of the bandwidth and flatness of the gain, we inserted the short stub into bias circuits and the compensation transmission line between common-source device and common-gate device, and then their lengths were optimized. Also, the input and output stages were designed using the matching method to obtain the broadband characteristic. From the measurement, we could confirm to extend bandwidth and flat gain by integrating the shunt peaking technology with the cascode configuration. The cascode amplifier shows the broadband characteristic from 19 GHz to 53.5 GHz. Also, the average gain of this amplifier is about 6.5 dB over the bandwidth.

• Journal of Environmental Science International
• /
• v.26 no.2
• /
• pp.231-238
• /
• 2017

Rapid industrial development has led to a serious problem of pollution in the industrial sector. With the increasing social need for environmental protection, research on air pollution prevention equipment for reducing pollutants in industrial processes is actively being undertaken. The deterioration of existent, installed facilities, their increased emission rates, and the strengthening of the effluent quality standards make complying with permissible emission standards difficult. In fact, installing new electric precipitators or complementing existent facilities is inevitable. The expansion and complementation of the installed electrical precipitators have led to improvements in dust collection efficiency, shorter working times, and lower costs. Because of its easy installation and simple manufacturing process, the production method with the discharge electrode of an electric precipitator is widely used. The following conclusions were reached by classifying discharge electrodes into four types based on the production method and mutually comparing them by their dust collection efficiency. None of the four types used in this study were damaged by impact. However, we were able to confirm some strain from the compression sites of both type A and type B. Both type B and type C are expected to have greater dust collection efficiencies than the other models due to their large vibration transmissibility. Moreover, the high vibrational energy is expected to cause rapping damage during its operation. Particularly, in the case of type B, some of the strain was found at the end of the compression site. The coupling schemes of both type C and type D are out of vibration transmissibility. On the other hand, the ability to maintain straightness and solidity of the side is regarded as outstanding and stable. Type D has outstanding on-site workability, considering the presence of locking, structural stability, and work conditions. From these experiments, we determined that type C is the most ideal connection method of discharge electrode, considering its construction period of renovation. Type C is inferior to type D with regard to on-site workability. However, type C has outstanding dedusting transmission with regard to the straightness, solidity maintenance, and vibration of shearing stress.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.1
• /
• pp.139-145
• /
• 2016

Dumbbell is the most basic topology that can be used in almost all kind of network experiment within it or just by little expansion. While Transmission Control Protocol TCP is the basic protocol that is used for the connectivity among networks and stations. TCP major and basic goal is to provide path and services to different applications for communication. For that reason TCP has to transfer a lot of data through a communication medium that cause serious congestion problem. To calculate the congestion problem, different kind of pre-cure solutions are developer which are Loss Based Variant and Delay Based Variant. While LBV keep track of the data that is going to be passed through TCP protocol, if the data packets start dropping that means congestion occurrence which notify as a symptom, TCP CUBIC use LBV for notifying the loss. Similarly the DBV work with the acknowledgment procedure that is used in when data ACK get late with respect to its set data rate time, TCP COMPOUND/VAGAS are examples of DBV. Many algorithms have been purposed to control the congestion in different TCP variants but the loss of data packets did not completely controlled. In this paper, the congestion control algorithms are implemented and corresponding results are analyzed in Dumbbell topology, it is typically used to analyze the TCP traffic flows. Fairness of throughput is evaluated for different TCP variants using network simulator (NS-2).

• Journal of KIISE:Databases
• /
• v.33 no.2
• /
• pp.239-249
• /
• 2006

Interoperability has been deemphasized from the hospital information system in general, because it is operated independently of other hospital information systems. This study proposes a future-oriented hospital information system through the design and actualization of the HL7 clinical document architecture. A clinical document is generated using the hospital information system by analysis and designing the clinical document architecture, after we defined the item regulations and the templates for the release form and radiation interpretation form. The schema is analyzed based on the HL7 reference information model, and HL7 interface engine ver.2.4 was used as the transmission protocol. This study has the following significance. First, an expansion and redefining process conducted, founded on the HL7 clinical document architecture and reference information model, to apply international standards to Korean contexts. Second, we propose a next-generation web based hospital information system that is based on the clinical document architecture. In conclusion, the study of the clinical document architecture will include an electronic health record (EHR) and a clinical data repository (CDR), and also make possible medical information-sharing among various healthcare institutions.

• Clean Technology
• /
• v.27 no.3
• /
• pp.223-231
• /
• 2021

In order to address many issues associated with large volume changes of silicon, which has very low electrical conductivity but offers about 10 times higher theoretical capacity than graphite (Gr), a silicon nanoparticles/hollow carbon (SiNP/HC) composite having bimodal-mesopores was prepared using silica nanoparticles as a template. A control SiNP/C composite without a hollow structure was also prepared for comparison. The physico-chemical and electrochemical properties of SiNP/HC were analyzed by X-ray diffractometry, X-ray photoelectron spectroscopy, nitrogen adsorption/desorption measurements for surface area and pore size distribution, scanning electron microscopy, transmission electron microscopy, galvanostatic cycling, and cyclic voltammetry tests to compare them with those of the SiNP/C composite. The SiNP/HC composite showed significantly better cycle life and efficiency than the SiNP/C, with minimal increase in electrode thickness after long cycles. A hybrid composite, SiNP/HC@Gr, prepared by physical mixing of the SiNP/HC and Gr at a 50:50 weight ratio, exhibited even better cycle life and efficiency than the SiNP/HC at low capacity. Thus, silicon/carbon composites designed to have hollow spaces capable of accommodating volume expansion were found to be highly effective for long cycle life of silicon-based composites. However, further study is required to improve the low initial coulombic efficiency of SiNP/HC and SiNP/HC@Gr, which is possibly because of their high surface area causing excessive electrolyte decomposition for the formation of solid-electrolyte-interface layers.

• Journal of the Korean Institute of Gas
• /
• v.23 no.2
• /
• pp.74-81
• /
• 2019

Expansion turbine system to recover the electricity energy from natural gas transmission stations is a well-known technique. The turbo-expander efficiency depends on the ratio of the natural gas flow rates to the design flow rate of the turbo-expander. However, if there is a big difference of the natural gas flow rate through the pressure letdown station because of seasonal supply pattern, that is, high flow rate in winter while low flow rate in summer, single turbo-expander system is not so efficient as to recover the pressurized energy from the low flow-rate natural gas. Therefore, we have proposed a new concept of double turbo-expander system: one is a big capacity and the other a small capacity. Here we have theoretically computed the electric powers at the pressure reduction from 18.5 bar to 7.5 bar depending on the inlet conditions of temperature and flow rate. The calculated electricity generation has been increased by 30% from 12.4 MW in a single turbo expander to 16.1 MW in the proposed double turbo-expander system when a minimal design efficiency of 0.72 is applied.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.41 no.1
• /
• pp.57-64
• /
• 2021

The speed change lane is installed at the point where the roads are connected on the urban roads, reducing the relative speed to facilitate traffic communication. However, in the case of the speed limit of 30 km/h in accordance with the implementation of the safe speed "5030" in the city, the standard is ambiguous, and there are criticisms about the installation of the transmission lane. This study conducted a pilot study on the traffic patterns of the speed change lanes, focusing on the section where the safe speed "5030" policy was scheduled to be implemented after theoretical consideration of the speed change lanes. After on-site investigation, as a result of analyzing the traffic pattern according to the travel speed of the main road according to road conditions and traffic conditions, the effectiveness of the speed change lane according to the safety speed "5030" was analyzed. In this study, the installation criteria for speed change lane by speed were presented. The criteria is that "speed change lanes should not be installed when the speed limit is 30 km/h, and speed change lanes should be installed when the speed limit is 50 km/h." The criteria will be considered as a reference when establishing engineering standards for connection of other facilities in urban areas in the future. It is expected that unnecessary restrictions on individuals' exercise of private property rights will be minimized, smooth traffic flow and secure safety by the installation of speed change lanes and expansion of turning radius.

• Journal of Cadastre & Land InformatiX
• /
• v.51 no.2
• /
• pp.107-123
• /
• 2021

In recent years, due to the continuous density and urbanization of space, the expansion of awareness of rights, the need for landscape conservation, and the development of construction technology, the conventional flat land use has been deviated from the conventional flat land use, and the transmission line, urban railway, parking lot, communal district, underground shopping mall, pipeline, etc. Although 3D spatial activities are carried out in the form of 3D space, there are considerable difficulties in administration to manage the 3D use of land due to the inadequacy of related regulations. In this background, for the administration that can manage Sectional Superficies, which is a representative case of 3D spatial use of parcels, which is a registered unit of land, first, the law on the establishment and management of spatial information, and cadastral re-examination from the legal and institutional aspects Standardization of 3D space registration through amendments to the Special Act, etc. and the formation of consensus among related departments. Second, in technical and administrative aspects, the registration of Sectional Superficies based on cadastral survey results, establishment of a platform for integrated management of location and attribute data, and registration method was found to be in need of improvement. As suggested in this study, by registering and managing Sectional Superficies, it is possible to manage various 3D land use of not only ground space or surface space but also underground space. It is expected to be able to register and manage lot-based 3D land use efficiently.

• Proceedings of the Botanical Society of Korea Conference
• /
• 1994.09a
• /
• pp.29-39
• /
• 1994

Serious issues about the changes in the environmental conditions on earth associated with human activities have arisen, and the interest in these problems has increased. It is urgent to determine how the expansion of terrestrial UV-B radiation due to the stratospheric ozone depletion influences living matters. In this connection, we have been investigating the effects of UV-B radiation on the growth of rice cultivars (Oryza sativa L.). We report here some physiological and genetic aspects of resistance to inhibitory effects of UV-B radiation on growth of rice cultivars as described below. Elevated UV radiation containing large amount of UV-B and a small amount of UV-C inhibited the development of plant height, the photosynthetic rate and the chlorophyll content in rice plants in a phytotron. Similar results were obtained in experiments, in which elevated UV-V radiation. Similar results were obtained in experiments, in which elevated UV-B radiation (transmission down to 290 nm) was applied instead of UV-B radiation containing a small amount of UV-C. The inhibitory effects of UV radiation was alleviated by the elevated CO2 atmospheric environment or by the exposure to the high irradiance visible radiation. The latter suggested the possibility that the resistance to the effects of UV radiation was either due to a lower sensitivity to UV radiation or to a greater ability to recover from the injury caused by UV radiation through the exposure to visible radiation. The examination of cultivar differences in the resistance to UV radiation-caused injuries among 198 rice cultivars belonging to 5 Asian rice ecotypes (aus, aman, boro, bulu and tjeleh) from the Bengal region and Indonesia and to Japanese lowland and upland rice groups showed the following: Various cultivars having different sensitivities to the effects of UV radiation were involved in the same ecotype and the same group, and that the Japanese lowland rice group and the boro ecotype were more resistant. Among Japanese lowland rice cultivars, Sasanishiki (one of the leading varieties in Japan) exhibited more resistance to UV rakiation, while Norin 1 showed less resistance, although these two cultivars are closely related. It was thus indicated that the resistance to the inhibitory effects of UV radiation of rice cultivars is not simply due to the difference in the geographical situation where rice cultuvars are cultivated. Form the genetic analysis of resistance to the inhibitory effects of UV radiation on growth of rice using F2 plants generated by reciprocally crossing Sasanishiki and Norin 1 and F3 lines generated by self-fertilizing F2 plants, it was evident that the resistance to the inhibitory of elebated UV radiation in these rice plants was controlled by recessive polygenes.

• Korean Journal of Poultry Science
• /
• v.36 no.2
• /
• pp.177-186
• /
• 2009

It is well-known that unregulated over-expression of foreign gene may have unwanted physiological or toxic effects in transgenic animals. To circumvent these problems, we constructed retrovirus vector designed to express the foreign gene under the control of the tetracycline-inducible promoter. However, gene expressions in the tetracycline-inducible expression system (Tet system) are not completely regulated but a little leaky due to the inherent defects in conventional Tet-based systems. A more tightly controllable regulatory system can be achieved when the advanced versions ($rtTA2^SM2$) of rtTA and a minimal promoter in responsive components (pTRE-tight) are used in combination therein. In this study, we tried to produce human thrombopoietin (hTPO) from various target cells and transgenic chickens using the retrovirus vector combined with Tet system. hTPO is the primary regulator of platelet production and has an important role in the survival and expansion of hematopoietic stem cells. In a preliminary experiment in vitro, higher hTPO expression and tighter expression control were observed in chicken embryonic fibroblast (CEF) cells. We also measured the biological activity of the hTPO using Mo7e cells whose proliferation is dependant on hTPO. The biological activity of the recombinant hTPO from CEF was higher than both its commercial counterpart and hTPO from other target cells. The recombinant retrovirus was injected beneath the blastoderm of non-incubated chicken embryos (stage X). Out of 138 injected eggs, 15 chicks hatched after 21 days of incubation. Among them, 8 hatched chicks were hTPO positive. When the Go transgenic chicken was fed doxycycline (0.5 mg per 1 gram of feed), a tetracycline derivative, hTPO concentration of the transgenic chicken blood was 200 ng/mL. Germline transmission of the transgene was confirmed in sperm of the Go transgenic roosters. These results are informative to establish transgenic chickens as bioreactors for the mass production of commercially valuable and biological active human cytokine proteins.