• Journal of Korean Society of Steel Construction
• /
• v.9 no.2 s.31
• /
• pp.269-275
• /
• 1997

Wind tunnel test results and their interpretations, which were performed to study the aerodynamic stability of tower of self-anchored suspension bridge, are presented in this paper. Tower and full models were tested under smooth and turbulent flow conditions. In the case of the tower with inclined two columns, the vibration due to wakes were occurred at wide velocity zone because the wakes with various frequencies were generated by inclined upstream column. It has to be emphasized that the vibration characteristics of the tower in the self-anchored suspension bridge may be very sensitive to the longitudinal boundary conditions of the girder at the supports. Because of the two natural frequency of the tower, out-of-plane bending and torsional, were not well separated, coupled motions were observed in a wide range of wind velocity. The effectiveness of corner cut, countermeasure to reduce the tower vibrations, was also studied. It has been found that 1:10, comer cut size to column width, may be the most effective ratio for reducing the vibrations.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.1
• /
• pp.35-44
• /
• 1990

Most of the medium-size ships are powered by large-bore, long-stroke, slow-speed and two-stroke diesel engines in order to improve the fuel efficiency. Such a propulsion plant develops low-frequency excitation forces/moments of significant magnitude. A RO/RO car/truck carrier is also one of the cases. In this paper, the rational methods for analysis of vertical and coupled horizontal-torsional vibrations are presented. Taking account of unusual characteristics of the hull form and structural systems, the emphasis is put on modelling methods based on beam analogy, calculation of system parameters such as added mass and its center, polar added-mass moment of inertia, shear coefficient of hull sections and coupling degree in antisymmetric modes, and modal analysis of forced vibrations.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2005.04a
• /
• pp.548-555
• /
• 2005

Since soil-structure interactions are one of the most important subjects in the structural/foundation engineering, much study concerning the soil-structure interactions had been carried out. One of typical structures related to the soil-structure interactions is the strip foundation which is basically defined as the beam or strip rested on or supported by the soils. At the present time, lack of studies on dynamic problems related to the strip foundations is still found in the literature. From these viewpoint, this paper aims to theoretically investigate dynamics of the elliptic strip foundations and also to present the practical engineering data for the design purpose. Differential equations governing the free, out-of-plane vibrations of such sap foundations we derived, in which effects of the rotatory and torsional inertias and also shear deformation are included although the warping of the cross-section is excluded. Governing differential equations subjected to the boundary conditions of free-free end constraints are numerically solved for obtaining the natural frequencies and mode shapes by using the numerical integration technique and the numerical method of non-linear equation.

• Earthquakes and Structures
• /
• v.11 no.2
• /
• pp.347-369
• /
• 2016

The main objective of this paper is the robust multi-objective optimization design of semi-active tuned mass damper (STMD) system using genetic algorithms and fuzzy logic. For optimal design of this system, it is required that the uncertainties which may exist in the system be taken into account. This consideration is performed through the robust design optimization (RDO) procedure. To evaluate the optimal values of the design parameters, three non-commensurable objective functions namely: normalized values of the maximum displacement, velocity, and acceleration of each story level are considered to minimize simultaneously. For this purpose, a fast and elitist non-dominated sorting genetic algorithm (NSGA-II) approach is used to find a set of Pareto-optimal solutions. The torsional effects due to irregularities of the building and/or unsymmetrical placements of the dampers are taken into account through the 3-D modeling of the building. Finally, the comparison of the results shows that the probabilistic robust STMD system is capable of providing a reduction of about 52%, 42.5%, and 37.24% on the maximum displacement, velocity, and acceleration of the building top story, respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• v.5 no.1
• /
• pp.34-51
• /
• 1981

Lately, due to increasing engine output by high supercharging, heavy crankshaft and propeller mass, as well as long strokes attended with the reduced crankshaft axial stiffness, the critical crankshaft axial vibration has frequently appeared in maneuvering range of the engine. Some investigators have developed calculating methods of natural frequencies and resonant amplitudes for crankshaft axial vibrations. But their reliabilities are uncertain as the estimated crankshaft axial stiffness are incorrect. The calculating procedure of these natural frequencies is practically analogous to the classical calculation of torsional vibration frequencies, except for an important difference due to the relationship of the axial stiffness of a crank and the angle between the crank and other, especially the adjacent, cranks. In this paper, 6 calculation formulae of crankshaft axial stiffness already published and a theoretically- developed one by authors are checked by comparing their calculating results with those measured values of one model crankshafat and three full-scale actual crankshafts. Also, the calculating methods of the crankshaft axial free vibration are investigated and their computer programs are developed. Finally, those developed computer programs are applied to calculating one model crankshaft and two full-scale actual crankshafts of ship's propulsion engines and their calculated results are compared with those measured values.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.703-706
• /
• 2005

Since soil structure interactions are one of the most important subjects in the structural/foundation engineering, much study concerning the soil structure interactions had been carried out. One of typical structures related to the soil structure interactions is the strip foundation which is basically defined as the beam or strip rested on or supported by the soils. At the present time, lack of studies on dynamic problems related to the strip foundations is still found in the literature. From these viewpoint this paper aims to theoretically investigate dynamics of the parabolic strip foundations and also to present the practical engineering data for the design purpose. Differential equations governing the free, out o plane vibrations of such strip foundations are derived, in which effects of the rotatory and torsional inertias and also shear deformation are included although the warping of the cross-section is excluded. Governing differential equations subjected to the boundary conditions of free-free end constraints are numerically solved for obtaining the natural frequencies and mode shapes by using the numerical integration technique and the numerical method of nonlinear equation.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.5 no.2
• /
• pp.29-37
• /
• 1996

High speed engines with high power are increasingly on demands and almost engines employ crankshafts Such problems as bending and torsional vibrations become the point at issue in crankshaft analysis and design. In this study to overcome the diffiiculty with the large amount of computation in finite element vibration analysis of a crankshaft, a reduction method based on influence coefficient and lumped parameter is presented. which reduces the computation amount effectively and can be used in vibrational analysis and design of any types of crankshafts Crank journal and pinparts are meodelled as elements with 6degrees of freedom per node. Crank web part is modelled using equivalent mass and stiffness matices . based up on lumped parameter and influence coefficient respectively to reduce total degrees of freedom considerablely. To confirm the scheme of the study the results are compared with the known data and they are coincident. Also a simple crankshaft is designed and manufactured for experiments. The calculated results using reduction method and the experimental results agree well The scheme of this study can be utilized in evaluation results agree well. The calculated result are compared with the known data and they are coincident. Also a simple crankshaft is designed and manufactured for experiments. The calculated results using reduction method and the experimental results agree well. The scheme of this study can be utilized in evaluation and development of high speed engine.

• Wind and Structures
• /
• v.24 no.5
• /
• pp.481-500
• /
• 2017

A novel three-degree-of-freedom (DOF) forced vibration system has been developed for identification of aeroelastic (self-excited) load parameters used in time-domain response analysis of wind-excited flexible structures. This system is capable of forcing sinusoidal motions on a section model of a structure that is used in wind tunnel aeroelastic studies along all three degrees of freedom - along-wind, cross-wind, and torsional - simultaneously or in any combination thereof. It utilizes three linear actuators to force vibrations at a consistent frequency but varying amplitudes between the three. This system was designed to identify all the parameters, namely, aeroelastic- damping and stiffness that appear in self-excited (motion-dependent) load formulation either in time-domain (rational functions) or frequency-domain (flutter derivatives). Relatively large displacements (at low frequencies) can be generated by the system, if required. Results from three experiments, airfoil, streamlined bridge deck and a bluff-shaped bridge deck, are presented to demonstrate the functionality and robustness of the system and its applicability to multiple cross-section types. The system will allow routine identification of aeroelastic parameters through wind tunnel tests that can be used to predict response of flexible structures in extreme and transient wind conditions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.11
• /
• pp.1306-1313
• /
• 2009

Dynamic and static behaviors of a three-dimensional catenary system for a high-speed railway are analyzed by using the finite element method. Considering tensions in the contact wire and the messenger wire, we drive the equations of motion for the catenary system. These equations are for the longitudinal, transverse, vertical and torsional motions. After establishing the weak form, the weak forms are spatially discretized with newly defined two-node beam elements. With the discretized equations, a finite element computer program is developed for the static and dynamic analyses. The static deflections of the catenary system, which are important for good contact between the pantograph and the contact line, are computed when the gravity is applied. On the other hand, we analyze the natural frequencies and the corresponding natural modes of the catenary system. The dynamic responses of the system are also investigated when applying a load to the contact line. For verification of the developed finite element program, vibrations of the catenary system are measured and they are compared to computed time responses.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.6 s.67
• /
• pp.58-63
• /
• 2005

The estimation of springing responses for recent ships is carried out, and application to a ship design is described. To this aim, springing effects on hull girder were re-evaluated, including non-linear wave excitations and torsional vibrations of the hull. The Timoshenko beam model was used to calculate stress distribution on the hull girder, using the superposition method. The quadratic strip method was employed to calculate the hydrodynamic forces and moments on the hull. In order to remove the irregular frequencies, we adopted 'rigid lid' on the hull free surface level, and addedasymptotic interpolation along the high frequency range. Several applications were carried out on the following existing ships: The Bishop and Price's container ship, S-175 container ship, large container, VLCC, and ore carrier. One of them is compared with the ship measurement result, while another with that of the model test. The comparison between the analytical solution and the numerical solution for a homogeneous beam-type artificial ship shows good agreement. It is found that Most springing energy comesfrom high frequency waves for the ships having low natural frequency and North Atlantic route etc. Therefore, the high frequency tail of the wave spectrum should be increased by $\omega$$\^{-3}$ instead of $\omega$$\^{-4}$ or $\omega$$\^{-5}$ for the springing calculation.