• 한국농공학회지
• /
• 제44권3호
• /
• pp.73-84
• /
• 2002

Nominal shear strength of concrete beam is the combined strength of concrete shear strength and steel shear strength in current design code. But Torsional moment strength of concrete is neglected in calculation of the nominal torsional moment strength of reinforced concrete beam in current revised code. Tensile stress of concrete strut between cracks is still in effect due to tension stiffening effect. But the tensile stresses of concrete after cracking are neglected in bending and torsion in design. The torsional behavior is similar to the shear behavior in mechanics. Therefore the torsional moment strength of concrete should be concluded to the nominal torsional moment strength of reinforced concrete beam. To verify the validity of the proposed model, the nominal torsional moment strengths according to CEB, two ACI codes(89, 99) and proposed model are compared to experimental torsional strengths of 55 test specimens found in literature. The nominal torsional moment strengths by the proposed model show the best results.

• Computers and Concrete
• /
• 제29권 5호
• /
• pp.303-321
• /
• 2022

The current design equations for predicting the torsional capacity of RC members underestimate the torsional strength of under-reinforced members and overestimate the torsional strength of over-reinforced members. This is because the design equations consider only the yield strength of torsional reinforcement and the cross-sectional properties of members in determining the torsional capacity. This paper presents an analytical model to predict the thickness of shear flow path in RC beams subjected to pure torsion. The analytical model assumes that torsional reinforcement resists torsional moment with a sufficient deformation capacity until concrete fails by crushing. The ACI 318 code is modified by applying analytical results from the proposed model such as the average stress of torsional reinforcement and the effective gross area enclosed by the shear flow path. Comparison of the calculated and observed torsional strengths of existing 129 test beams showed good agreement. Two design variables related to the compressive strength of concrete in the proposed model are approximated for design application. The accuracy of the ACI 318 code for the over-reinforced test beams improved somewhat with the use of the approximations for the average stresses of reinforcements and the effective gross area enclosed by the shear flow path.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.445-448
• /
• 1999

The minimum shear and torsional reinforcement provisions in ACI 318-95 are still empirical. This paper describes the derivation of a rational approach for minimum shear and torsional reinforcement in beams so as to preclude brittle failure in shear and torsion. This is ensured by specifying that the beam's ultimate capacity of shear and torsion should be greater than its cracking shear and torsion. The formula presented herein for computing minimum shear and torsional reinforcement shows the need for modification of current provision for the minimum shear and torsion reinforcement.

• 콘크리트학회논문집
• /
• 제23권1호
• /
• pp.57-65
• /
• 2011

전단과 비틀림모멘트가 동시에 작용하는 경우에 단면에는 각각의 영향으로 인하여 전단응력이 발생하므로 이 두 응력을 더하여 설계할 수 있다. 그러나 현행 콘크리트구조설계기준에서는 전단과 비틀림모멘트 설계식을 단위가 서로 틀린 단면력으로 표현하여 분포도를 그리기 위해서는 각각의 좌표에 분리해서 그려야만 한다. 만약에 이 두 하중으로 인한 단면력을 응력으로 표현하게 되면 두 전단응력을 더하여 하나의 좌표에 표현할 수 있고, 설계 결과도 동시에 그려 넣을 수 있으므로 쉽게 설계과정을 인식하여 실수를 최소화 할 수 있을 것이다. 게다가 현행 기준에서는 전단과 비틀림모멘트에 대한 설계식을 단위 길이 당 스터럽의 단면적으로 표현되는 $A_{\upsilon}/s$나 $2A_{\upsilon}/s$로 제시하여, 설계과정에서 이 값들의 크기나 상황을 정확하게 인식하기 거의 불가능하게 된다. 설계에서 먼저 스터럽의 종류를 결정하여 단면적 $A_{\upsilon}$나 $A_t$가 결정되므로 설계식들을 스터럽의 간격에 대한 식으로 정리하면 설계과정을 명확하게 인식할 수 있고 또한 여러 설계과정도 간단하게 정리되어 이해하기 쉽도록 할 것이다.

• 콘크리트학회논문집
• /
• 제14권1호
• /
• pp.24-32
• /
• 2002

전단문제에서는 일부 설계기준(AASHTO 1994)에 이미 수정압축장이론이 도입되었다. 그리고 현행 콘크리트 설계기준에는 콘크리트의 전단강도가 철근의 전단강도와 합하여 공칭전단강도를 계산하고 있다. 그러나 최근에 개정된 콘크리트설계기준에는 콘크리트의 비틀림강도가 공칭비틀림강도 계산에서 누락되었다. 콘크리트의 인장응력은 비록 크기가 작으나 균열후에 균열사이의 콘크리트에 존재한다. 그러나 휨과 비틀림문제에서는 균열 후 콘크리트의 인장강성은 생략되고 있다. 역학적으로 콘크리트보의 비틀림거동은 전단거동과 매우 유사하다. 그러므로 균열 후 콘크리트의 비틀림강도를 철근콘크리트 보의 공칭비틀림강도의 계산에 포함시켜야 한다. 본 논문에서는 콘크리트의 평균주인장응력이 이루는 콘크리트의 비틀림강도를 횡방향 비틀림철근의 비틀림강도와 함께 공칭비틀림강도를 구성함을 밝혔으며, 이의 타당성을 검증하기 위해 개정 전후의 ACI 의 설계기준에 의한 공칭비틀림강도와 함께 실험값과 비교하였다. 그 결과 본 논문이 제안한 모델에 의한 공칭비틀림강도가 가장 좋은 결과를 보였다.

• 한국전산구조공학회논문집
• /
• 제35권5호
• /
• pp.277-286
• /
• 2022

국내의 서비스 수준 지진(SLE)과 최대 고려 지진(MCE)의 두 RC 건물 구조물의 실험 및 해석 결과에서 얻은 탄성 및 비탄성 응답은 비틀림에 대한 전단 및 비틀림 거동에서 저항 메커니즘의 특성을 연구하는데 사용될 수 있다. 불균형 구조의 특성 연구에서는 전단력 및 비틀림 모멘트에 대한 병진 변형 및 비틀림 변형의 상호 작용 효과를 나타내는 방정식이 제안하였다. 탄성과 비탄성 거동에서 힘과 변형 사이에 상관 관계 유무가 다르기 때문에 증분 전단력과 증분 비틀림 모멘트를 최대 벽 프레임 변형을 중심으로 항복, 제하 및 재하중 단계로 구분하여 해당 증분 변형 및 증분 비틀림 변형 측면에서 해석을 수행하였다. 두 가지 주요 지배 모드의 탄성 조합에서 병진 변형은 주로 전단력에 기여하는 반면 비틀림 변형은 전체 비틀림 모멘트에 크게 기여한다. 그러나 비탄성 응답에서는 증분 병진 변형이 증분 전단력과 증분 비틀림 모멘트 모두에 기여하게 된다. 따라서 주어진 방정식을 이용하여 비탄성 응답에서 비틀림의 편심 감소, 비틀림 강성 저하 및 겉보기 에너지 생성과 같은 모든 현상들을 설명하였다.

• Wind and Structures
• /
• 제3권4호
• /
• pp.279-289
• /
• 2000

The main purpose of this paper is to demonstrate the necessity of considering wind load combinations even for low-rise buildings. It first discusses the overall quasi-static wind load effects and their combinations to be considered in structural design of low-rise buildings. It was found that the maximum torsional moment closely correlates with the maximum along-wind base shear. It was also found that the instantaneous pressure distribution causing the maximum along-wind base shear was quite similar to that causing the maximum torsional moment, and that this asymmetric pressure pattern simultaneously accompanies considerable across-wind and torsional components. Secondly, the actual wind pressure distributions causing maximum quasi-static internal forces in the structural frames are conditionally sampled and their typical pressure patterns are presented.

• Earthquakes and Structures
• /
• 제9권1호
• /
• pp.145-171
• /
• 2015

Due to earthquakes, many structures suffered extensive damages that were attributed to the torsional effect caused by mass, stiffness or strength eccentricity. Due to this type of asymmetry torsional moments are generated that are imposed by means of additional shear forces developed at the vertical resisting structural elements of the buildings. Although the torsional effect on the response of reinforced concrete buildings was the subject of extensive research over the last decades, a quantitative index measuring the amplification of the shear forces developed at the vertical resisting elements due to lateral-torsional coupling valid for both elastic and elastoplastic response states is still missing. In this study a reliable index capable of assessing the torsional effect is proposed. The performance of the proposed index is evaluated and its correlation with structural response quantities like displacements, interstorey drift, base torque, shear forces and upper diaphragm's rotation is presented. Torsionally stiff, mass eccentric single-story and multistory structures, subjected to bidirectional excitation, are considered and nonlinear dynamic analyses are performed using natural records selected for three hazard levels. It was found that the proposed index provides reliable prediction of the magnitude of torsional effect for all test examples considered.

• 한국소음진동공학회논문집
• /
• 제15권4호
• /
• pp.499-505
• /
• 2005

In this paper, a new type of pi+ezoelectric stepping motor is designed, manufactured and tested. This motor is composed of piezoelectric torsional actuator and a pair of one-way clutch bearings. The torsional actuator consists of 16-polygonal tube of piezoceramic that can produce an angular displacement associated with shear mode. One-way clutch bearing converts oscillation of torsional actuator into a continuous stepping rotation. The proposed stepping motor does not require any conversion mechanism for stepping motion like any other motors. In the design process, the shear resonance mode of piezoelectric actuator is analyzed by using a commercial finite element analysis program, and the performance of the fabricated torsional actuator is measured. $0.124^{\circ}$ of maximum angular displacement is measured in square wave excitation on the actuator only. The stepping motor is manufactured by assembling a pair of one-way clutch bearings and the torsional actuator. The maximum rotation speed of 72rpm and the blocking torque of 3.136 mNm are measured at 3540 Hz and 100V/mm. Once the proposed piezoelectric stepping motor is miniaturized, it can be used for many compact and precise moving applications.

• 한국철도학회논문집
• /
• 제3권1호
• /
• pp.34-41
• /
• 2000

The analysis of static and dynamic characteristics of reinforced roadbed materials was performed through model and laboratory tests. The strength characteristic of reinforced roadbed materials such as HMS-25 and soil were investigated through the unconfined axial compression test, the model soil box test and the combined resonant column and torsional shear test. The unconfined axial compression strength of HMS-25 shows a steady increasement in strength due to the chemical hardening reaction between HMS-25 and water. The result of model soil box test reveals that railroad roadbed of HMS-25 is better than that of soil in several aspects, such as, bearing capacity and settlement. The combined resonant column and torsional shear test result indicates that shear modulus of HMS-25 and soil increase with the power of 0.5 to the confining pressure and linear relationship to normalized shear modulus and damping ratio.