• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.2
• /
• pp.94-98
• /
• 2002

QFT(Quantitative Feedback Theory) is a very practical design technique that emphasizes the use of feedback for achieving the desired system performance tolerances in despite of plant uncertainty and disturbance. The gain-phase loop shaping procedure of QFT is employed to design controller, until the bounds at desired frequencies are satisfied. This paper presents a transfer function synthesis using TLS(Total Least Squares) and offers a loop shaping method with the suggested technique. An example illustrates a feasibility of the presented algorithm.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.317-321
• /
• 1989

The FIC(Flat Integrated Circuits)is widely used for good productivity but very difficult for visual identification. The required position tolerance is 0.05mm and orientation tolerance is 0.25 degree for assembly. The research was performed to detect FIC defects and to estimate the placement of FIC within the tolerances. In this study an automatic visual system is developed, which can successfully perform a fine assembly operation using the cartesian robot.

• 제어로봇시스템학회:학술대회논문집
• /
• 1986.10a
• /
• pp.534-539
• /
• 1986

This paper considers the ring rolling process contorl and treats the problem of controlling the pressure roll and conical roll motion which critically affects final quality of the rolled products. Since the process dynamics reveals nonlinear characteristics and parameter uncertainty, an adaptive control scheme was applied. The results show that this proposed adaptive control scheme can produce rolled rings of closer dimensional tolerances as compared with nonadaptive control system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.5
• /
• pp.680-687
• /
• 1999

An extensive study on miniaturized bandpass filter(BPF) appropriate for mobile communication systems is presented in this paper. The miniaturization has been accomplished by incorporating low-loss high-index materials inside a resonating cavity fabricated in silicon substrate using micromachining etching techniques. By use of materials with dielectric constant $\varepsilon_r$=500, filters with volume less than 0.11 $mm^3$ have been designed at the center frequency of 5.8 GHz with 3.3% bandwidth. The electrical performances and design tolerances of these filters for a variety of materials and shapes are discussed and design guidelines are presented herein.

• Journal of Korea Society of Industrial Information Systems
• /
• v.5 no.3
• /
• pp.77-86
• /
• 2000

The main objectives of this dissertation is to propose a forth generation index C for the case where the target value T is not equal to the midpoint of the specification limits (i.e. asymmetric tolerances), and show that this index is more sensitive compared to the standard PCI's in detacting small shifts of the process mean from the target value. In conclusion, in this dissertation , a new methods for estimating a measure of process capability for non-normally distributed variable data is proposed using the percentage nonconforming.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.22 no.49
• /
• pp.33-41
• /
• 1999

The original tolerances, which are assigned by designers on the basis of handbooks and experience, cannot always be expected to be optimal or feasible, because they may yield an unacceptable manufacturing costs. So the systematic tolerance design considering manufacturing costs should be done. Therefore, this research analyzes the tolerance within the tolerance design using Monte-Carlo simulation method and sensitivity analysis and using genetic algorithm by tolerance allocation method. The genetic algorithm was developed for allocation of the optimal tolerance under the manufacturing limitation cost.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.5
• /
• pp.914-923
• /
• 2002

Recently, there has been considerable interest in micro gyroscopes made of silicon chips. It can be applied to many micro-electro-mechanical systems (MEMS): devices for stabilization, general rate control, directional pointing, autopilot systems, and missile control. This paper shows how the mechanical design of the gyroscope can be done using axiomatic design, followed by the application of the Taguchi robust design method to determine the dimensions of the parts so as to accommodate the dimensional variations introduced during manufacturing. Functional requirements are defined twofold. One is that the natural frequencies should have fixed values, and the other is that the system should be robust to large tolerances. According to the Independence Axiom, design parameters are classified into a few groups. Then, the detailed design process is performed fellowing the sequence indicated by the design matrix. The dimensions of the structure are determined to have constant values fur the difference of frequencies without consideration of the tolerances. It is noted that the Taguchi concept is utilized as a unit process of the entire axiomatic approach.

• Journal of Korean Ophthalmic Optics Society
• /
• v.3 no.1
• /
• pp.189-199
• /
• 1998

The system for optical tolerances of completion spectacles was made to sum of the accumulated error - the circumstances on composing prescription, the visual-distance, the tilting angle, the losing of a temple, the vertex distance, the axis of toric lens and the sloping of lens etc. It was given by the relation of allowed values size(T) and power(D), $T=T_0e^{-aD}$. Here, $T_0$ is the size of allowed values of plane-lens with power is 0 and ${\alpha}$ is the factor of allowed values. In case of being adopted to new form s tolerance corresponding to RAL 915, for the tolerance is large direction, the factor of allowed values ${\alpha}$ is $0.166(T_0=5.90)$ and for the tolerance is small direction, the factor of allowed values ${\alpha}$ is $0.166(T_0=2.95)$.

• Journal of Korean Ophthalmic Optics Society
• /
• v.9 no.2
• /
• pp.397-415
• /
• 2004

This study surveyed differences among KS, ISO, JIS and ANSI ophthalmic spectacle lenses standards. These standards applied to several lenses that were in common currency and we checked over problems and improvements in KS. KS corresponded to ISO, for the most part, and ANSI, partly. But terms, definitions, progressive power lenses standards, UV transmittance and base curves clauses did not exist in KS. There was no differences between nominal data and actual data in important clauses estimation-minimum requirements on refractive power, tolerances on the size of lenses, material and surface quality. But tolerances of thickness, base curves, UV and visible transmittance values were not existing, there were differences among several ophthalmic spectacle lenses in the test of these clauses. These requirements will be needed for better and more comfortable vision.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.1
• /
• pp.85-94
• /
• 2014

Tolerance accumulation has serious effect on the performance of an assembled body. This paper proposes the method which analyzes tolerance accumulation using Monte Carlo Simulation. This method can predict tolerance distribution of fully assembled body using the dimensional tolerance distribution of each part to be assembled. In this analysis, it is assumed that the tolerance of each part has the nominal distribution or uniform distribution. This analysis method is applied to ECV(External Control Valve), and the accumulated tolerance of the fully assembled ECV is obtained from the analysis. The results show that initial tolerance given to each part do not meet the design requirement of ECV. Hence, the tolerances of each part are modified and the additional analysis with the modified tolerances yields the results which satisfy the design requirements of ECV.