• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1168-1170
• /
• 2000

A half bridge time sharing type high frequency resonant inverter to give VVVF function in the inverter used as power source of induction heating at high frequency is presented in this paper, this paper also realize the output control of independence irrespective of the switching frequency using Phase-Shift. The analysis of the proposed circuit is generally described by using the normalized parameters. Also, the principle of basic operation and the its characteristics are estimated by the parameters, such as switching frequency, the variation of phase angle(${\varphi}$) of Phase-Shift. It is certain that the proposed circuit will be used and expanded in the high frequency power supplies like induction heating systems.

• Journal of the Korean Data and Information Science Society
• /
• v.28 no.4
• /
• pp.911-925
• /
• 2017

We investigate the properties of multivariate Shewart control charts with VSI procedure for monitoring simultaneous monitoring mean vector and covariance matrix in term of ANSW (average number of switches), probability of switch and ASI (average sampling interval), ATS (average time to signal). From examining the ANSW values, we know that it does not switch frequently. The VSI control charts are superior to the corresponding FSI control charts in terms of ATS. And, it can be also seen that the VSI procedures have substantially fewer switches for small or moderate shifts of the mean vector and variances.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.12
• /
• pp.2828-2833
• /
• 1997

In this paepr, we have proposed an enhanced TDM with WDM hybrid photonic switching architecture, which has much simpler configuration and requires less hard ware. the basic module consists of arrayed waveguide grating (AWG) for wavelength division, compressor and fiber delay lines for time division. When compared with other systems, we proved that the proposed switch is suitable for large capacity photonic switching system due to less complexity and lower cost in implementation than the previous ones.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.6
• /
• pp.616-623
• /
• 1999

Elevator velocity pattern is basL'C! on combining the time-based velocity pattern according to which the car m trip from starting position to vicinity of target position, and distance-based velocity pattern for precise landing ( of car. To obtain the lide comfortability, the impact caused by velocity pattern switching should be minimizLD b by removing the discontinuity of velocity and acceleration. In this paper, new velocity pattern generation m method which ensure the continuity of velocity and acceleration during pattern switching is proposed. P ProPOSLD velocity pattern also shorten the landing time to the target position.

• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.199-201
• /
• 1994

The switching characteristics of $As_{10}Ge_{15}Te_{75}$ thin film were investigated under dc bias. It was found that the threshold voltage depends on thickness, electrode distance, annealing time and temperature, respectively. The threshold voltage is increased as the thickness and the electrode distance is increased, while the threshold voltage is decreased in proportion to the increased annealing time and temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.22-23
• /
• 2006

Proton irradiation technology was used for improvement of switching characteristics of the PT-IGBT. Proton irradiation was carried out at 5.56 MeV energy with $1{\times}10^{12}/cm^2$ doze from the back side of the wafer. Characterization of the device was performed by I-V, breakdown voltage, threshold voltage, and turn-off delay time measurement. For irradiated device by 5.56 MeV energy, the breakdown voltage and the threshold voltage were 730 V and 6.5~6.6 V, respectively. The turn-off time has been reduced to 170 ns, which was original $6\;{\mu}s$ for the un-irradiated device.

• Macromolecular Research
• /
• v.10 no.6
• /
• pp.345-358
• /
• 2002

The electrical conductivity during vulcanization process was measured as a function of time for the system of TiC loaded styrene-butadiene rubber (SBR) composites. The phenomenon of negative and positive temperature coefficients of conductivity and its conduction mechanism were also studied for the SBR polymeric composites. The current-voltage characteristics of the polymeric composites were non-linear in high voltage and showed a switching effect. The effects of temperature on the thermal conductivity and effective dielectric constant were measured. The measured parameters were found to be dependent on TiC concentration. The electromagnetic wave shielding (EMS) of the SBR-TiC polymeric composite was also examined. The SBR filled with TiC could be expected to be promising novel smart polymeric composites for self-electrical heating, temperature sensor, time delay switching, and electro-magnetic wave shielding effectiveness.

• Korean Journal of Optics and Photonics
• /
• v.9 no.5
• /
• pp.348-352
• /
• 1998

By employing the Berreman's backflow model, we investigated the effect of liquid crystal parameters on the optical switching characteristics of a bistable twisted-nematic liquid crystal cell. We found that d/p is the most important parameter for high speed operation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.4
• /
• pp.302-306
• /
• 2019

We investigated a solution-derived $Y_2O_3$ film treated by ion beam (IB) irradiation as a liquid crystal (LC) alignment layer. With IB irradiation, homogeneous LC alignment was achieved irrespective of the annealing temperature. To verify the effect of IB irradiation, we conducted surface analyses such as X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). As $Y_2O_3$ is a high-k material, the electro-optical properties of the twisted nematic (TN) cells were superior to those of conventional TN cells based on a rubbed polymer, with an LC rising time of 4.1ms and falling time of 2.9ms. The IB-irradiated $Y_2O_3$ is a good alternative as an alignment layer for fast-switching TN LC displays.

• Journal of Integrative Natural Science
• /
• v.12 no.3
• /
• pp.78-84
• /
• 2019

In many cases, the quality of a product is determined by several correlated quality variables. Control charts have been used for a long time widely to control the production process and to quickly detect the assignable causes that may produce any deterioration in the quality of a product. Numerical switching performances of multivariate cumulative sum control chart for simultaneous monitoring all components in the dispersion matrix ${\Sigma}$ under multivariate normal process $N_p({\underline{\mu}},{\Sigma})$ are considered. Numerical performances were evaluated for various shifts of the values of variances and/or correlation coefficients in ${\Sigma}$. Our computational results show that if one wants to quick detect the small shifts in a process, CUSUM control chart with small reference value k is more efficient than large k in terms of average run length (ARL), average time to signal (ATS), average number of switches (ANSW).