• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.283-284
• /
• 2018

The rear side surface of tiles act have protrusions that helps secure the adhesion between the tile and the mortar for tile setting. Conventional height of the rear side usually ranges between 1 to 1.5 mm, and the molding method is classified in between press type and compression type during the manufacturing process, with most tiles being produced by the former method. In sites where adhesion failures were observed, tiles were taken to examine the cause of defect. It was determined that height was irregular at the rear side surface. Based on these findings, an experiment was conducted to determine the correlation between the rear surface and the bonding strength of tiles.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.2
• /
• pp.83-87
• /
• 1995

Impact-bouncing height of steel balls dropped from 1m height on various floor materials were measured to evaluate impact-bouncing characteristics depending on floor materials and the effect of these properties on walkability and fatigue of humanbody. Stone and tile finished concrete floor showed the highest bouncing height of around 70%, and soil showed the lowest bouncing height of around 3%. The second highest bouncing height was about 40% which corresponded to terazo finished concrete floor and about twice as high as the bouncing height on concrete floor without finishing. The impact-bouncing height could be lowered to 15~20% by using gum tile on concrete floor. Steel showed similar bouncing height to concrete floor, and wood-based materials showed the second lowest bouncing height next to soil. Among wood-based materials, hardwood species having higher specific gravities showed relatively high bouncing height of 8~24%, softwood species having low specific gravities showed relatively lower bouncing height of 5~18%, and wood composites showed bouncing height of 8~18%. Among all the materials used in this study, wood-based floor materials corresponded to the bouncing height of 10~15% which is considered to be best for humanbody. Surface painting on wood-based materials increased the bouncing height, and the number of bouncing of steel balls after dropping from 1m height increased as the bouncing height increased.

• Journal of Korea Game Society
• /
• v.8 no.1
• /
• pp.71-77
• /
• 2008

The geometric structure constructs terrain from height map and non-periodically tiling with Wang tile for the detail description. It will be able to express detail bump using parallax mapping to add decal data together with height data in tile. We solve the problem when the real-time rendering and propose improving of parallax mapping for the terrain.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.257-262
• /
• 2001

A numerical analysis is undertaken to show tile influence of bearing design parameters on tile load capacity of air lubricated spiral grooved thrust bearing. The governing equation derived from the mass balance is solved by the finite difference method. Optimal values for various design parameters are obtained to maximize the load capacity. The design parameters are the groove angle, the groove width ratio, the groove height ratio, arid the seal ratio.

• Korean Journal of Plant Resources
• /
• v.4 no.1
• /
• pp.23-27
• /
• 1991

This experiment was conducted to establish shade-method suited to on tile artificial propagation of Lycoris radiata HERB. The ligilt intensity in the native habitatwas 30 kux in March and 3.2 Klux from June to sept. The average light intensityin tile open area was 137 Klux in June. The plant height and number of Ieaves wasgood at the 35% to 55% shadeing net. Bloonling time of Lycoris radiata HERB was inthe last of Sept. Yeild of bulb was increased in 35% to 55% of shadeing net.

• Journal of the Ergonomics Society of Korea
• /
• v.35 no.6
• /
• pp.503-517
• /
• 2016

Objective: The aim of this study was to evaluate the effectiveness of 3 dimensional contoured pillow through analyzing contact pressure and to suggest its design guidelines through analyzing the posture of head and neck area. Background: The quality of sleep is a very important factor closely related with human's health. To improve the quality of sleep, the verification of design factors affecting the posture of the head and neck is needed, and a pillow design that can induce proper posture is required. Method: This study measured the contact pressures of the two reference groups (bead and cotton pillows) as a method to evaluate the design effectiveness of the contoured pillow. This study proposed 3-dimensional design guidelines by drawing anthropometry (head length) affecting cervical curvature angle (CCA) through the measurement of the participants' cervical curvature angles. Results: In the design effectiveness evaluation, the contact pressure of cervical region was higher than that of a reference group (cotton pillow), and contract area increased, and contract pressure decreased in the shape distributing the occipital region's body pressure. This study proposed pillow's cervical supporting height by percentile of a head length [head length (%tile) (cervical supporting height) affecting the posture of the head and neck: 14.6cm (5%tile) (6.2cm), 15.5cm (25%tile) (6.7cm), 16.4cm (50%tile) (7.1cm), and 19.3cm (75%tile) (8.9cm)]. Conclusion: This study confirmed the contoured pillow's design effectiveness maintaining cervical angle comfortable to sleep with the shape supporting the cervical vertebrae and by reducing the contact load of the occipital region. Also, this study proposed pillow design guidelines based on the 3-dimensional contoured pillow design effectiveness, through which the study laid the foundation for pillow design in a systematic method. Application: The results of this study are expected to be utilized as the basis data by which the optimum pillow type and pillow design according to main percentile can be standardized.

• Journal of ILASS-Korea
• /
• v.10 no.1
• /
• pp.10-16
• /
• 2005

To investigate the effect of shockwave on diesel spray characteristics under ultra high pressure injection, the velocity of spray tip and shock wave were investigated using the visualization of spray by schlieren method. Spray characteristics such as the spray radius, height, and droplets size were analyzed. It is found in this study that shock wave, produced by ultra high injection pressure, propagates faster than spray tip. Spray radius of right side of nozzle tip was shorter than that of left side and spray height of right side of nozzle tip was thicker than that of left side. Droplets sue was increased at 414MPa in injection pressure because of pressure gradient between inner and outer of tile spray caused by shockwave.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.770-774
• /
• 2003

We propose the re-design method of modal parameters to depress the 2nd resonance peak of the ultra-slim-height optical pick-up actuator. With the addition of tile counter mode near the 2nd resonance frequency, we can achieve the gain margin which is sufficient to meet the system requirement. It would alleviate the burden of the additional filter for a high-speed drive.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.7 s.184
• /
• pp.159-167
• /
• 2006

The impact time history of human body with K2 rifle on stand shooting posture is analyzed and compared with experimental results. Analysis model is Korean 50% tile of twenties and height, weight is 174 cm, 62 kgf respectively. The muscle and bone human model of Korean man's twenties 50% tile is applied. ADAMS program is used for kinematic analysis and human model is developed by Life Mod program. The effect of the ground support condition, grip position and human weight factor are studied. Maximum impact force of shoulder is 784 N. The horizontal displacement of K2 rifle muzzle is 2.9 cm.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.374-381
• /
• 2001

Surface roughness plays a significant role in friction, wear, and lubrication in machine components. Most engineering surfaces have tile nogaussian height distrubution. So, in this study, elastic-plastic contact simulations are conducted for not only gaussian surfaces but also nongaussian surfaces. Nongaussian rough surface considering the kurtosis is generated numerically. The contact simulation model takes into account the plastic deformation behaviors of asperities by setting a celing on their contact pressure at material hardness value. It will be shown that the performace variables such as real contact area fraction, plastic area fraction and average gap are sensitive to the characteristics of surface geometry according to kurtosis.